High-Temperature Properties of Langasite

1999 ◽  
Vol 604 ◽  
Author(s):  
H. Fritze ◽  
H. L. Tuller ◽  
G. Borchardt ◽  
T. Fukuda

AbstractMaterials such as langasite (La3Ga5SiO14) and related compounds are promising candidates for piezoelectric applications at high temperatures. In particular, langasite does not exhibit phase transformations up to the melting point of 1470 °C. Langasite was investigated with respect to potential applications in high temperature resonator devices. In contrast to current resonator materials, we have observed bulk oscillations at temperatures of up to 750 °C in langasite devices. At 700 °C the mass load response for 0.78 mm thick resonators is approximately 0.10 µg/Hz.At elevated temperatures, the bulk resistivity of the resonator devices cannot be neglected due to attenuation of the resonance signal. Therefore, the temperature dependence of the electrical properties of langasite resonator devices, including bulk resistivity, capacity and resonance frequency were measured and are presented. The electrical conductivity is characterized by an activation energy of 105 kJ/mol. In order to confirm langasites stability with respect to oxidation-reduction reactions, we examined the oxygen diffusivity by measuring 18O tracer profiles by SIMS. The diffusivity along the Y-axis is given by D = 5-10−5 exp(-140 kJ/mol / RT) cm2/s in the temperature range from 500 to 800 °C. Langasite shows low oxygen diffusion coefficients with respect to other materials which might be investigated using a langasite microbalance. This would, for example, enable oxygen diffusion kinetics to be examined in YBa2Cu3O6 at 600 °C by means of 18O/16O exchange.

Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1525
Author(s):  
Hao-ran Qi ◽  
Deng-xiong Shen ◽  
Yan-jiang Jia ◽  
Yuan-cheng An ◽  
Hao Wu ◽  
...  

High-temperature-resistant polymeric adhesives with high servicing temperatures and high adhesion strengths are highly desired in aerospace, aviation, microelectronic and other high-tech areas. The currently used high-temperature resistant polymeric adhesives, such as polyamic acid (PAA), are usually made from the high contents of solvents in the composition, which might cause adhesion failure due to the undesirable voids caused by the evaporation of the solvents. In the current work, electrospun preimidized polyimide (PI) nano-fibrous membranes (NFMs) were proposed to be used as solvent-free or solvent-less adhesives for stainless steel adhesion. In order to enhance the adhesion reliability of the PI NFMs, thermally crosslinkable phenylethynyl end-cappers were incorporated into the PIs derived from 3,3’,4,4’-oxydiphthalic anhydride (ODPA) and 3,3-bis[4-(4-aminophenoxy)phenyl]phthalide (BAPPT). The derived phenylethynyl-terminated PETI-10K and PETI-20K with the controlled molecular weights of 10,000 g mol−1 and 20,000 g mol−1, respectively, showed good solubility in polar aprotic solvents, such as N-methyl-2-pyrrolidinone (NMP) and N,N-dimethylacetamide (DMAc). The PI NFMs were successfully fabricated by electrospinning with the PETI/DMAc solutions. The ultrafine PETI NFMs showed the average fiber diameters (dav) of 627 nm for PETI-10K 695 nm for PETI-20K, respectively. The PETI NFMs showed good thermal resistance, which is reflected in the glass transition temperatures (Tgs) above 270 °C. The PETI NFMs exhibited excellent thermoplasticity at elevated temperatures. The stainless steel adherends were successfully adhered using the PETI NFMs as the adhesives. The PI NFMs provided good adhesion to the stainless steels with the single lap shear strengths (LSS) higher than 20.0 MPa either at room temperature (25 °C) or at an elevated temperature (200 °C).


2019 ◽  
Vol 96 ◽  
pp. 02004
Author(s):  
Tebogo Mashifana

A million tons of Phosphogypsum (PG) is stacked in the environment every year and is progressively considered an asset. South African construction industry is expanding as a result of infrastructural developments in the country, the reuse of PG in this industry is considered for recycling and reducing the stacks in landfills. Phosphogypsum is known for its limited ability to use in cement industry due to its phosphorus and radionuclides impurities. This study was conducted to reduce these impurities and investigate the probability of PG application in building and construction. Leaching of PG with citric acid was conducted whereby a relative proportion of P2O5 and radionuclides was reduced in the material, constituents which contributes to strengths reduction. Optimum moisture Contents and maximum dry densities were determined for various PG content mix designs in which Lime and Fly Ash were added to stabilise PG material. The composites were compacted at various moisture contents and cured at low and elevated temperatures of at 40 °C and 80 °C for 4 days. The results obtained shows that for unconfined compressive strengths; the composites produced from PG, and cured at high temperature qualified for the use in construction industry.


2020 ◽  
Vol 20 (3) ◽  
pp. 1859-1865 ◽  
Author(s):  
Zhongliu Wen ◽  
Wei Zhou ◽  
Lan Long ◽  
Yang Li

As oxidation is inevitable during application of microwave absorbing materials (MAM) exposed to oxygen-containing atmosphere at elevated temperatures. The investigations concerning influences of oxidation on microstructure and microwave absorption (MA) properties are of great significance. Aiming to better regulating MA for Si3N4-based ceramics serviced in high temperature environment, the evolution of MA properties of SiCw/Si3N4 composites (SwSN) after oxidation at 1200 °C in ambient air for short time was studied. It was found that after oxidation for 7.5 h, both the real and imaginary permittivity of SwSN showed only slight decrease due to good oxidation protection provided by dense SiO2 layer formed on the surface. Moreover, SwSN after short-time of oxidation also showed an almost negligible decline in MA properties. SwSN which has good oxidation resistance and stable microwave attenuation abilities was subjected to oxidation at 1200 °C for short time. The results showed its favorable and potential applications in high-temperature microwave absorption fields.


Fuel ◽  
2020 ◽  
Vol 267 ◽  
pp. 117160 ◽  
Author(s):  
Qian Xu ◽  
Zhenwei Zou ◽  
Yushi Chen ◽  
Kang Wang ◽  
Zhiwei Du ◽  
...  

Sensors ◽  
2021 ◽  
Vol 21 (17) ◽  
pp. 5978
Author(s):  
Thierry Aubert ◽  
Ninel Kokanyan ◽  
Omar Elmazria

Langasite crystals (LGS) are known for their exceptional piezoelectric properties at high temperatures up to 1000 °C and more. In this respect, many studies have been conducted in order to achieve surface acoustic wave (SAW) sensors based on LGS crystals dedicated to high-temperature operations. Operating temperatures of more than 1000 °C and 600 °C for wired and wireless sensors, respectively, have been reached. These outstanding performances have been obtained under an air atmosphere since LGS crystals are not stable in high-temperature conditions under a low-oxygen atmosphere due to their oxide nature. However, if the stability of bulk LGS crystals under a high-temperature air atmosphere is well established, the surface deterioration under such conditions has been hardly investigated, as most of the papers dedicated to LGS-based SAW sensors are essentially focused on the development of thin film electrodes that are able to withstand very elevated temperatures to be combined with LGS crystals. Yet, any surface modification of the substrate can dramatically change the performance of SAW sensors. Consequently, the aim of this paper is to study the stability of the LGS surface under a high-temperature air environment. To do so, LGS substrates have been annealed in an air atmosphere at temperatures between 800 and 1200 °C and for durations between one week and one month. The morphology, microstructure, and chemical composition of the LGS surface was examined before and after annealing treatments by numerous and complementary methods, while the surface acoustic properties have been probed by SAW measurements. These investigations reveal that depending on both the temperature and the annealing duration, many defects with a corolla-like shape appear at the surface of LGS crystals in high-temperature prolonged exposure in an air atmosphere. These defects are related to the formation of a new phase, likely an oxiapatite ternary compound, the chemical formula of which is La14GaxSi9−xO39−x/2. These defects are located on the surface and penetrate into the depth of the sample by no more than 1–2 microns. However, SAW measurements show that the surface acoustic properties are modified by the high-temperature exposure at a larger deepness of at least several tens of microns. These perturbations of the LGS surface acoustic properties could induce, in the case of LGS-based SAW sensors operating in the 434 MHz ISM band, temperature measurement errors around 10 °C.


Author(s):  
M. Larsen ◽  
R.G. Rowe ◽  
D.W. Skelly

Microlaminate composites consisting of alternating layers of a high temperature intermetallic compound for elevated temperature strength and a ductile refractory metal for toughening may have uses in aircraft engine turbines. Microstructural stability at elevated temperatures is a crucial requirement for these composites. A microlaminate composite consisting of alternating layers of Cr2Nb and Nb(Cr) was produced by vapor phase deposition. The stability of the layers at elevated temperatures was investigated by cross-sectional TEM.The as-deposited composite consists of layers of a Nb(Cr) solid solution with a composition in atomic percent of 91% Nb and 9% Cr. It has a bcc structure with highly elongated grains. Alternating with this Nb(Cr) layer is the Cr2Nb layer. However, this layer has deposited as a fine grain Cr(Nb) solid solution with a metastable bcc structure and a lattice parameter about half way between that of pure Nb and pure Cr. The atomic composition of this layer is 60% Cr and 40% Nb. The interface between the layers in the as-deposited condition appears very flat (figure 1). After a two hour, 1200 °C heat treatment, the metastable Cr(Nb) layer transforms to the Cr2Nb phase with the C15 cubic structure. Grain coarsening occurs in the Nb(Cr) layer and the interface between the layers roughen. The roughening of the interface is a prelude to an instability of the interface at higher heat treatment temperatures with perturbations of the Cr2Nb grains penetrating into the Nb(Cr) layer.


Author(s):  
H. Kung ◽  
T. R. Jervis ◽  
J.-P. Hirvonen ◽  
M. Nastasi ◽  
T. E. Mitchell ◽  
...  

MoSi2 is a potential matrix material for high temperature structural composites due to its high melting temperature and good oxidation resistance at elevated temperatures. The two major drawbacksfor structural applications are inadequate high temperature strength and poor low temperature ductility. The search for appropriate composite additions has been the focus of extensive investigations in recent years. The addition of SiC in a nanolayered configuration was shown to exhibit superior oxidation resistance and significant hardness increase through annealing at 500°C. One potential application of MoSi2- SiC multilayers is for high temperature coatings, where structural stability ofthe layering is of major concern. In this study, we have systematically investigated both the evolution of phases and the stability of layers by varying the heat treating conditions.Alternating layers of MoSi2 and SiC were synthesized by DC-magnetron and rf-diode sputtering respectively. Cross-sectional transmission electron microscopy (XTEM) was used to examine three distinct reactions in the specimens when exposed to different annealing conditions: crystallization and phase transformation of MoSi2, crystallization of SiC, and spheroidization of the layer structures.


Alloy Digest ◽  
2005 ◽  
Vol 54 (12) ◽  

Abstract Wieland K-88 is a copper alloy with very high electrical and thermal conductivity, good strength, and excellent stress relaxation resistance at elevated temperatures. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: CU-738. Producer or source: Wieland Metals Inc.


Alloy Digest ◽  
1956 ◽  
Vol 5 (7) ◽  

Abstract DOWMETAL HZ32XA is a magnesium-thorium-zinc-zirconium alloy having good high temperature creep resistance, and is recommended for applications at elevated temperatures. It is used in the artificially aged condition (T5). This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as creep. It also includes information on high temperature performance as well as heat treating, machining, and joining. Filing Code: Mg-26. Producer or source: The Dow Chemical Company.


Alloy Digest ◽  
1972 ◽  
Vol 21 (7) ◽  

Abstract UDIMET 105 is a nickel-base alloy which was developed for service at elevated temperatures. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as creep. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: Ni-175. Producer or source: Special Metals Corporation.


Sign in / Sign up

Export Citation Format

Share Document