Room temperature conversion of X0.3V2O5· nH2O phase into X2V6O16· nH2O phase Influence of the nature of the cation X+

2004 ◽  
Vol 848 ◽  
Author(s):  
Olivier Durupthy ◽  
Saïd Es-salhi ◽  
Nathalie Steunou ◽  
Thibaud Coradin ◽  
Jacques Livage
Keyword(s):  
Vanadium Oxide ◽  
Room Temperature ◽  
Interlayer Space ◽  
Water Molecules ◽  
X Ray Diffraction ◽  
X Ray ◽  
Oxide Phases ◽  
New Phase ◽  
Supernatant Solution ◽  
Scanning Electron

ABSTRACTVarious cations (Li+, Na+, K+, NH4+, Cs+, Mg2+, Ca2+, Ba2+) were introduced during the formation of a V2O5. nH2O gel. Cation intercalated Xy V2O5. nH2O (y = 0.3 for X = Li+, Na+, K+, NH4+ or y = 0.15 for Mg2+, Ca2+, Ba2+) were first obtained at room temperature but some of them evolve upon ageing into a new phase: XV3O8. nH2O for X = Na+, K+, NH4+ and Cs+ or XV6O16. nH2O for X = Mg2+, Ca2+, Ba2+. All the vanadium oxide phases were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and infrared spectroscopy (IR); the supernatant solutions were analysed by 51V NMR spectroscopy. These vanadium oxide phases exhibit a layered structure with cations and water molecules intercalated within the interlayer space. The formation of the different phases depends mainly on the pH of the supernatant solution and on the nature of the cation.

scholarly journals A new hydrate of magnesium carbonate, MgCO3·6H2O

2020 ◽  
Vol 76 (3) ◽  
pp. 244-249
Author(s):  
Christine Rincke ◽  
Horst Schmidt ◽  
Wolfgang Voigt
Keyword(s):  
Crystal Structure ◽  
Aqueous Solution ◽  
Diffraction Pattern ◽  
Raman Spectra ◽  
Room Temperature ◽  
Magnesium Carbonate ◽  
Water Molecules ◽  
X Ray Diffraction ◽  
X Ray ◽  
New Phase

During investigations of the formation of hydrated magnesium carbonates, a sample of the previously unknown magnesium carbonate hexahydrate (MgCO3·6H2O) was synthesized in an aqueous solution at 273.15 K. The crystal structure consists of edge-linked isolated pairs of Mg(CO3)(H2O)4 octahedra and noncoordinating water molecules, and exhibits similarities to NiCO3·5.5H2O (hellyerite). The recorded X-ray diffraction pattern and the Raman spectra confirmed the formation of a new phase and its transformation to magnesium carbonate trihydrate (MgCO3·3H2O) at room temperature.

ROOM TEMPERATURE PHOTOLUMINESCENCE OF POLYCRYSTALLINE SIC PREPARED FROM CARBON-SATURATED SI MELT

2002 ◽  
Vol 16 (06n07) ◽  
pp. 1047-1051
Author(s):  
JIANPING MA ◽  
ZHIMING CHEN ◽  
GANG LU ◽  
MINGBIN YU ◽  
LIANMAO HANG ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Uv Light ◽  
X Ray Diffraction ◽  
X Ray ◽  
Room Temperature Photoluminescence ◽  
Composition And Structure ◽  
Light Excitation ◽  
Scanning Electron

Intense photoluminescence (PL) has been observed at room temperature from the polycrystalline SiC samples prepared from carbon-saturated Si melt at a temperature ranging from 1500 to 1650°C. Composition and structure of the samples have been confirmed by means of X-ray photoelectron spectroscopy, X-ray diffraction and scanning electron microscopy. PL measurements with 325 nm UV light excitation revealed that the room temperature PL spectrum of the samples consists of 3 luminescent bands, the peak energies of which are 2.38 eV, 2.77 eV and 3.06 eV, respectively. The 2.38 eV band is much stronger than the others. It is suggested that some extrinsic PL mechanisms associated with defect or interface states would be responsible to the intensive PL observed at room temperature.

Influence of Silicon Nitride on Properties of Corundum Based Castable

2013 ◽  
Vol 634-638 ◽  
pp. 2358-2361
Author(s):  
Jun Cong Wei ◽  
Li Rong Yang
Keyword(s):  
Electron Microscopy ◽  
Thermal Shock ◽  
Thermal Shock Resistance ◽  
Room Temperature ◽  
X Ray Diffraction ◽  
Cold Strength ◽  
X Ray ◽  
Refractory Castables ◽  
Shock Resistance ◽  
Scanning Electron

The effects of Si3N4 addition on the room temperature physical properties and thermal shock resistance properties of corundum based refractory castables were investigated using brown corundum, white corundum and alumina micropowder as the starting materials and pure calcium aluminate as a binder. The phase composition, microstructure, mechanical properties of corundum based castables were investigated by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results showed that as the increase in Si3N4 addition, the bulk density decreased and apparent porosity increased, the cold strength deduced. However, the residual strength rate increased. That is, the thermal shock resistance was improved. This is because even though the introduction of Si3N4 inhibited the sintering of material and deduced the compactness, microcracks were produced in the materials due to a difference in thermal expansion coefficient. So the thermal shock resistance of corundum based castable was improved.

N-type Ba0.2Co4Sb11.5Te0.5: Optimization of thermoelectric properties by different pressures

2019 ◽  
Vol 33 (03) ◽  
pp. 1950027 ◽  
Author(s):  
Jiaxiang Chen ◽  
Xiaopeng Jia ◽  
Yuewen Zhang ◽  
Haiqiang Liu ◽  
Baomin Liu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Seebeck Coefficient ◽  
Room Temperature ◽  
X Ray Diffraction ◽  
Absolute Value ◽  
X Ray ◽  
Coefficient Increase ◽  
Maximum Power Factor ◽  
Scanning Electron

The polycrystalline skutterudite [Formula: see text] were successfully synthesized from 1.5 GPa to 3.5 GPa by the high pressure and high temperature (HPHT) method. Negative Seebeck coefficient confirmed the n-type conductivity of all samples. The phase compositions of samples were investigated by X-ray diffraction (XRD) and the microstructures were observed by scanning electron microscopy (SEM). It was found that the grains appeared smaller and the grain boundaries became more abundant when pressures were higher. We measured the electrical properties from room temperature to 723 K. Both the electrical resistivity and absolute value of Seebeck coefficient increase with the increasing synthetic pressure. At 723 K, the maximum power factor of [Formula: see text] was obtained for the sample synthesized under 3 GPa. The maximum ZT value of 0.61 was reached by [Formula: see text] synthesized under 3 GPa and measured at 723 K.

scholarly journals Mechanical Activation of Smectite-Based Nanocomposites for Creation of Smart Fertilizers

2022 ◽  
Vol 12 (2) ◽  
pp. 809
Author(s):  
Maxim Rudmin ◽  
Santanu Banerjee ◽  
Boris Makarov ◽  
Kanipa Ibraeva ◽  
Alexander Konstantinov
Keyword(s):  
Electron Microscopy ◽  
Interlayer Space ◽  
Soil Leaching ◽  
X Ray Diffraction ◽  
Activation Time ◽  
Release Rates ◽  
X Ray ◽  
Weight Losses ◽  
Transmission Electron ◽  
Scanning Electron

This research presents the mechanical creation of smart fertilizers from a mixture of smectite and urea in a 3:2 ratio by using the planetary milling technique. The smectite–urea composites show intercalation between urea and mineral, which increases steadily with increasing activation time. A shift of X-Ray Diffraction basal reflections, intensities of Fourier transform infrared spectroscopy (FTIR) peaks, and weight losses in thermogravimetric analysis (TG) document the systematic crystallo-chemical changes of the composites related to nitrogen interaction with activation. Observations of the nanocomposites by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) corroborate the inference. Nitrogen intercalates with smectite in the interlayer space and remains absorbed either within micro-aggregates or on the surface of activated smectites. Soil leaching tests reveal a slower rate of nitrogen than that of traditional urea fertilizers. Different forms of nitrogen within the composites cause their differential release rates to the soil. The formulated nanocomposite fertilizer enhances the quality and quantity of oat yield.

scholarly journals EFFECT OF OPERATIONAL PARAMETER ON PHOTOCATALYTIC DEGRADATION OF OXAMYL PESTICIDE

2020 ◽  
Vol 4 (12) ◽  
pp. 74-84
Author(s):  
Brijesh Pare ◽  
Satish Piplode ◽  
Vaishali Joshi
Keyword(s):  
Photocatalytic Activity ◽  
Photocatalytic Degradation ◽  
Room Temperature ◽  
Light Irradiation ◽  
Solar Light ◽  
X Ray Diffraction ◽  
Operational Parameter ◽  
X Ray ◽  
Solar Light Irradiation ◽  
Scanning Electron

Flower like bismuth oxy chloride (BiOCl) was successfully synthesized by a simple hydrolytic method at room temperature. The precursor and as-prepared samples were characterized by X-ray diffraction (XRD), High Resolution Field Emission Scanning Electron Microscope (HR FESEM). The results indicated that the as-prepared BiOCl sample is self-assembled hierarchically with nano sheets. The photocatalytic activity of BiOCl was tested on the degradation of the Oxamyl (OM) under solar light irradiation. The results showed that pesticide molecules could be efficiently degraded over BiOCl under solar light irradiation. All the experiment were carried out in the following reaction condition, [OM] = 10-4 mol dm-3, BiOCl NPs= 40mg/50ml, pH= 6.3. Effect of operational parameter such as concentration of H2O2, K2S2O8, FeCl3, Fenton’s reagent (Fe3+/H2O2) and N2, O2 purging on the photocatalytic degradation was observed.

Surface analytical study of uranium exposed to low pressures of hydrogen at ∼ 80°C

2012 ◽  
Vol 1444 ◽  
Author(s):  
Robert M. Harker ◽  
Afiya H. Chohollo
Keyword(s):  
Room Temperature ◽  
Analytical Study ◽  
Treatment Cycle ◽  
X Ray Diffraction ◽  
Standard Samples ◽  
X Ray ◽  
Surface Precipitation ◽  
Pre Treatment ◽  
Low Pressures ◽  
Scanning Electron

ABSTRACTIdentical samples of uranium coupons were prepared and each exposed to hydrogen for different times (where this time is significantly less than a classically understood ‘induction time’). Samples were prepared from rolled depleted uranium stock: as-received oxide was removed on all surfaces and two faces (~12x12 mm) were polished to a sub-micron standard. Samples were individually taken through a Vacuum Thermal Pre-Treatment cycle from room temperature to 200°C to the reaction temperature (80°C) over 40 hours and subsequently exposed to 10 mbar O2 for 24 hours. After O2 was removed, the samples were exposed to hydrogen for pre-determined times of up to 48 minutes. Examination of the samples by Scanning Electron Microscopy (SEM) has, as expected, identified small features protruding from the surface believed to have been caused by sub-surface precipitation of UH3. In general these features are circular and isolated from each other, have a diameter of less than 3μm and appear as either ‘flat-topped’ or ‘domed’ morphology. In addition, longer time exposure samples show a predominance of ‘area attack’ where coalesced sub-surface precipitation appears to be confined to particular metal grains. X-Ray Diffraction (XRD) data show an increase in the quantity of UH3 with time.

The Influence of Mn Doping on the Dielectric Properties of Ba0.5Sr0.5TiO3 Ceramics

2016 ◽  
Vol 859 ◽  
pp. 18-23 ◽  
Author(s):  
Li Ping Zhao ◽  
Wen Hong Tao ◽  
Xing Hua Fu ◽  
Wen Zhe Cao ◽  
Guo Yuan Cheng ◽  
...  
Keyword(s):  
Dielectric Properties ◽  
Material Properties ◽  
Room Temperature ◽  
Sol Gel ◽  
Barium Nitrate ◽  
Strontium Nitrate ◽  
X Ray Diffraction ◽  
Mn Doping ◽  
X Ray ◽  
Scanning Electron

(Ba0.5Sr0.5)1-xMnxTiO3(x=0,0.01,0.03,0.05)ceramics were prepared via a new sol-gel method with titannium oxide, strontium nitrate, barium nitrate and manganous nitrate as raw materials.The effect of Mn doping on the microstructure and dielectric properties of the BST were characterized by field scanning electron microscopy,x-ray diffraction and impedance analyser.It was found that the dopted ions could not alter the basic crystal strcuture and they only improved the material properties as modified ions when x≤0.3.The (Ba0.5Sr0.5)1-xMnxTiO3 ceramics sintered at 1250°C for 2h exhibited good dielectric properties(er=1330,tand=0.03)at room temperature and f=1KHz when x=0.03 and the grains were regular and uniform ,indicating a dense microstrcture.

scholarly journals Properties of Nanostructure Bismuth Telluride Thin Films Using Thermal Evaporation

2017 ◽  
Vol 2017 ◽  
pp. 1-4 ◽  
Author(s):  
Swati Arora ◽  
Vivek Jaimini ◽  
Subodh Srivastava ◽  
Y. K. Vijay
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Bismuth Telluride ◽  
Room Temperature ◽  
Thermal Evaporation ◽  
Silicon Substrates ◽  
X Ray Diffraction ◽  
Thermal Evaporation Method ◽  
X Ray ◽  
Scanning Electron

Bismuth telluride has high thermoelectric performance at room temperature; in present work, various nanostructure thin films of bismuth telluride were fabricated on silicon substrates at room temperature using thermal evaporation method. Tellurium (Te) and bismuth (Bi) were deposited on silicon substrate in different ratio of thickness. These films were annealed at 50°C and 100°C. After heat treatment, the thin films attained the semiconductor nature. Samples were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM) to show granular growth.

Effect of Au on the Performance of Porous Silicon/V2O5 Nanorods Heterojunctions to NO2 Gas

NANO ◽  
2016 ◽  
Vol 11 (07) ◽  
pp. 1650079 ◽  
Author(s):  
Wenjun Yan ◽  
Ming Hu ◽  
Jiran Liang ◽  
Dengfeng Wang ◽  
Yulong Wei ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Porous Silicon ◽  
Room Temperature ◽  
Au Nanoparticles ◽  
Analytical Techniques ◽  
Heating Process ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

A novel composite of Au-functionalized porous silicon (PS)/V2O5 nanorods (PS/V2O5:Au) was prepared to detect NO2 gas. PS/V2O5 nanorods were synthesized by a heating process of pure vanadium film on PS, and then the obtained PS/V2O5 nanorods were functionalized with dispersed Au nanoparticles. Various analytical techniques, such as field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), have been employed to investigate the properties of PS/V2O5:Au. Herein, the PS/V2O5:Au sample exhibited improved NO2-sensing performances in response, stability and selectivity at room temperature (25[Formula: see text]C), compared with the pure PS/V2O5 nanorods. These phenomena were closely related to not only the dispersed Au nanoparticles acting as a catalyst but also the p-n heterojunctions between PS and V2O5 nanorods. Whereas, more Au nanoparticles suppressed the improvement of response to NO2 gas.

Sign in / Sign up

Export Citation Format

Share Document