scholarly journals Modeling pastille products recipe using unconventional raw materials in accordance with predetermined quality indicators

2016 ◽  
Vol 3 (1(29)) ◽  
pp. 21
Author(s):  
Олена Олександрівна Соколовська
Author(s):  
Е.Е. Ульянченко

Исследовано влияние приема прорезания средней жилки на основные качественные показатели табачного сырья. Исследования проводили на листьях основных сортотипов табака Трапезонд и Остролист по массовым ломкам. Прорезание жилки осуществляли на инновационном оборудовании экспериментальном образце линии подготовки листьев табака к сушке ЛПТС360 (ВНИИТТИ, Краснодар). Качество табачного сырья с прорезанной жилкой определяли по товарным сортам, технологическим и курительным свойствам, химическому составу по методикам лабораторного контроля ВНИИТТИ. Инновационный способ подготовки табака к сушке в едином потоке с применением технологического оборудования, включающего прорезатель, выявил положительный технологический результат. Установлена эффективность приема прорезания средней жилки: срок естественной сушки листьев с прорезанной жилкой сократился в 2,5 раза выход 1го товарного сорта сырья составил 74,60 87,93 выход волокна сырья с прорезанной жилкой превышает минимальное значение технологических норм (75) в 1,15 1,26 раз условный расход сырья на единицу курительных изделий меньше норматива на 6 25 улучшен основной показатель химического состава табачного сырья (число Шмука) в 1,6 4,6 раза у сортотипа Трапезонд, в 1,2 1,5 раза у сортотипа Остролист дегустационные свойства сырья не ухудшились. Инновационный способ подготовки листьев табака к сушке, включающий прием прорезания средней жилки, рекомендуется для применения в производстве табачного сырья. The influence of middle vein cutting method on the main quality indicators of tobacco raw materials is studied. Studies were carried out on the leaves of the main varieties of tobacco Trapezond and Ostrolist, on mass breakdowns. Vein cutting was carried out on the innovative equipment of the line of preparation of tobacco leaves for drying LPTS360 (GNU VNIITTI RAA, Krasnodar). The quality of tobacco raw materials with a cut vein was determined by commercial grades, technological and Smoking properties, chemical composition in accordance with the methods VNIITTI. An innovative method of preparing tobacco for drying in a single stream with the use of technological equipment, including a cutter, revealed a positive technological result. The period of natural drying of leaves with cut veins decreased by 2,5 times. The yield of the 1st commercial grade of raw materials was 74,60 87,93. The output of the fiber raw material with cut vein exceeds the minimum value of technological norms (75) in 1,15 1,26 times. Conditional consumption of raw materials per unit of Smoking products is less than the norm by 6 25. The method of cutting the middle vein of the leaves improves the main indicator in the chemical composition of tobacco raw materials (Schmuck ratio) 1,6 4,6 times in the variety Trapezond and 1,2 1,5 times in the variety Ostrolist. The tasting properties of raw materials have not deteriorated. Analysis of raw material quality indicators showed that the innovative method of cutting the middle vein is effective and recommended for use in the production of tobacco raw materials.


2021 ◽  
Vol 17 (1) ◽  
pp. 70-77
Author(s):  
E. Е. Ulyanchenko ◽  
N. N. Vinevskaya

Cultivation and use of Virginia 202 broadleaf skeletal variety for the production of smoking tobacco has broad prospects. Problems of post-harvest processing of large leaves with a massive midrib consist in high energy costs with an artificial drying method or the provision of facilities for long-term natural drying. The aim of the research is to apply physical method of cutting the leaf midrib to intensify drying and to determine the effect of this technique on the quality indicators of raw materials. It has been found that the technique of cutting the midrib on the Virginia 202 variety contributes to a significant optimization of the drying process without reducing the quality of raw materials. The drying time of leaves with the combined method is reduced by 2,8 times, with the natural method – by 2,3 times, and the quality indicators of raw materials improve. Commercial quality is characterized by the yield of 1 commercial grade, for combined drying the yield of 1 grade has increased in comparison with the control sample by 27% and amounted to 86,5%, with natural drying – the increase in yield is 4%. Cutting the midrib increases the fiber yield by 3–5% and contributes to an increase in the volumetric-elastic properties of the fiber, providing an economical consumption of raw materials for the production of smoking articles, the consumption is 676,8–753,8 g/1000 pcs. The gustatory quality improves, raw materials with a cut midrib have optimal values of the ratio of carbohydrate-protein balance in the range of 1,08–1,5, the strength is preserved due to the lower consumption of nicotine during the shorter drying period, in comparison with drying the leaf without cutting the midrib. Cutting the midrib in Virginia 202 is cost effective.


2021 ◽  
Vol 296 ◽  
pp. 07009
Author(s):  
Svetlana Gabelko ◽  
Olesya Ionova

When developing a diet for citizens with diseases of the gastrointestinal tract or obesity, it is necessary to adhere to a therapeutic diet in which bakery products and dairy products with berry fillers can be wholesome ingredients. In order to increase the range of berry fillers based on local plant raw materials, the physicochemical quality indicators were studied and the organoleptic evaluation of fillers with various types of thickeners was given.


Author(s):  
Ю.Н. НИКОНОВИЧ ◽  
Н.А. ТАРАСЕНКО

Исследовано влияние гидратированных пшеничных волокон Камецель FW 200 и апельсиновых волокон Citri-Fi 200, внесенных в тесто взамен части кондитерского жира для повышения пищевой и биологической ценности продукта, на свойства мягких вафель. Готовили образцы вафельного теста: контрольный – тесто без добавок, образцы теста с заменой 10, 15 и 20% кондитерского жира на пшеничные волокна Камецель FW 200, образцы теста с заменой 10, 15 и 20% кондитерского жира на апельсиновые волокна Citri-Fi 200 – и определяли технологические свойства изготовленных образцов теста – влажность, плотность и количество оттеков вафельного листа. Установлено, что внесение пищевых волокон Citri-Fi 200 в исследованных дозировках 10, 15 и 20% от массы жира в рецептуру вафельного теста увеличивает количество оттеков выше допустимого уровня, т. е. увеличивает потери сырья. Оптимальные качественные показатели имеет образец вафельного теста с добавкой 15% гидратированных пищевых волокон Камецель FW 200, внесение которых позволит увеличить пищевую ценность кондитерского изделия. The influence of hydrated wheat fibers Kametsel FW 200 and orange fibers Citri-Fi 200, introduced into the dough instead of the confectionery fat to improve the nutritional and biological value of the product on the properties of soft waffles was investigated. Wafer dough samples: control - dough without additives, dough samples with replacement of 10, 15 and 20% confectionery fat by wheat fibers Kametsel FW 200, dough samples with replacement of 10, 15 and 20% confectionery fat by orange fibers Citri-Fi 200 – prepared and determined their technological properties – humidity, density and the number of flows of the wafer sheet. It is established that the introduction of Citri-Fi 200 dietary fibers in the studied dosages of 10, 15 and 20% by weight of fat in the formulation of wafer dough increases the number of flows the dough above the permissible level, i.e. increases the loss of raw materials. A sample of wafer dough with the addition of 15% hydrated dietary fiber Kametsel FW 200 has optimal quality indicators.


2020 ◽  
pp. 36-48
Author(s):  
V.A. Kochetkova

The article provides an overview of the production of binders, sets out the requirements for the quality indicators of colored asphalt, the technology of production of binders, and also considers promising areas in the production of colorless binders. The purpose of the work was to create an affordable organic binder based on light hydrogenated petroleum polymer resins and use the developed binder for colored asphalt. To achieve this goal, we analyzed patents for the production of binders, on the basis of which the composition of raw materials was selected, and studied the physical and mechanical characteristics of the obtained samples on both hydrogenated and non-hydrogenated petroleum polymer resin.


Author(s):  
Е.Е. УЛЬЯНЧЕНКО

При производстве табачного сырья важную роль играет сокращение продолжительности сушки табачных листьев. Одним из способов интенсификации сушки свежеубранных табачных листьев является прием прорезания средней жилки (ПСЖ) листьев вдоль волокон. По результатам исследований 2019–2020 гг. была создана база данных табачного сырья, полученного при естественном способе сушки с применением приема ПСЖ, которая может служить информационным материалом для производителей табака. Проведена оптимизация процесса сушки табачного листа ПСЖ по показателям качества табачного сырья для расширенного диапазона сортотипов табака. Объектом исследований были сорта отечественной селекции, включенные в Государственный реестр селекционных достижений, допущенные к использованию: Самсун 85, Вирджиния 202, Юбилейный новый 142, Трапезонд 92, Трапезонд 204, Дюбек 33, Американ 287 и Крупнолистный Ильский (находится в стадии государственных испытаний). Критерием оценки эффективности применения приема ПСЖ на исследованных сортах табака являлся совокупный сравнительный анализ следующих показателей контрольных (без ПСЖ листа) и опытных образцов: уровень интенсификации сушки, показатели товарного качества, технологических свойств и химического состава полученного сырья. Установлено, что ПСЖ позволяет интенсифицировать процесс сушки в 1,3–2,46 раза в зависимости от сорта табака и положительно влияет на технологические свойства сырья, у большинства сортов увеличивается выход волокна и сохраняются объемно-упругие свойства. Динамика сушки оказывает влияние на изменение химического состава сырья. В процессе сушки за счет гидролизации солей никотина и его освобождения путем окисления кислородом воздуха уровень никотина в ряде образцов снижается в пределах 10–30%. Чем выше содержание никотина, тем выше крепость табака, грубее его вкус. Изменения углеводно-белкового соотношения в сторону повышения углеводов улучшают вкусовые характеристики сырья. По каждому исследованному сорту не удалось выявить закономерной зависимости его структуры и характера процесса сушки при ПСЖ с преобразованиями химического состава сырья. На основе анализа технологических и качественных показателей табачного сырья, представленных в разработанной базе данных по интенсификации сушки различных сортов табака с применением приема ПСЖ табачных листьев, можно планировать выбор оптимального способа сушки для каждого сорта табака, позволяющего повысить эффективность использования сырья и улучшить его качественные характеристики. In the production of tobacco raw materials, reducing the drying time of tobacco leaves plays an important role. One of the ways to intensify the drying of freshly harvested tobacco leaves is the method of cutting the middle vein (CMV) of the leaves along the fibers. Based on the results of research in 2019–2020, a database of tobacco raw materials obtained by a natural drying method using CMV reception was created, which can serve as information material for tobacco producers. The optimization of the process of drying the CMV tobacco leaf according to the quality indicators of tobacco raw materials for an expanded range of tobacco variety types was carried out. The object of research was the varieties of domestic selection included in the State Register of Breeding Achievements, approved for use: Samsun 85, Virginia 202, Yubileyny novy 142, Trapezond 92, Trapezond 204, Dubek 33, American 287 and Krupnolistnyy Ilskiy (under state testing). The criterion for evaluating the effectiveness of the use of CMV intake on the studied tobacco varieties was a cumulative comparative analysis of the following indicators of control (without CMV sheet) and experimental samples: the level of drying intensification, indicators of commercial quality, technological properties and chemical composition of the obtained raw materials. It is established that CMV allows to intensify the drying process by 1,3–2,46 times, depending on the tobacco variety and has a positive effect on the technological properties of raw materials, most varieties increase the yield of fiber and retain volume-elastic properties. The dynamics of drying affects the change in the chemical composition of raw materials. During the drying process, due to the hydrolysis of nicotine salts and its release by oxidation with air oxygen, the nicotine level in a number of samples decreases within 10–30%. The higher the nicotine content, the higher the strength of tobacco, it is coarser in taste. Changes in the carbohydrate-protein ratio in the direction of increasing carbohydrates improve the taste characteristics of raw materials. For each studied variety, it was not possible to identify a regular dependence of its structure and the nature of the drying process at CMV with transformations of the chemical composition of raw materials. Based on the analysis of technological and qualitative indicators of tobacco raw materials presented in the developed database on the intensification of drying of various varieties of tobacco using the use of CMV of tobacco leaves, it is possible to plan the choice of the optimal drying method for each variety of tobacco, which allows to increase the efficiency of using raw materials and improve its quality characteristics.


2011 ◽  
Vol 312-315 ◽  
pp. 1198-1203 ◽  
Author(s):  
A.N. Dmitriev ◽  
Yu.A. Chesnokov ◽  
G.Yu. Arzhadeeva ◽  
Yu.P. Lazebnaya

The iron ore raw materials and coke quality is the basic reserve of improvement of blast furnace technology. Some of the quality indicators of iron ore raw materials and coke and their influence on the main parameters of the blast furnace smelting are considered in this paper.


Author(s):  
Yurii Polievoda ◽  
Alla Solomon

The development of modern equipment and technology leads to healthy competition, which in turn allows you to freely choose a machine or installation for the separation of liquid inhomogeneous systems. Each production when choosing equipment takes into account the relevant factors and its specifics. Mathematical and statistical planning of a multifactorial experiment was used to refine the glycerin quality indicators and determine their weight. The article constructs the response surfaces of the optimization criteria, which allow us to clearly illustrate the dependences of the values of the mass fraction of pure glycerin and energy consumption on individual optimization parameters. The research method includes the selection of optimal modes of operation of the vibrocentric machine for purification of liquid glycerol-containing raw materials according to technical and economic criteria for evaluation and determination of quality indicators of purified glycerol with variation of processing time, process temperature, etc. During the study, special attention was paid to the main operating parameters of this vibrating machine, namely: amplitude-frequency, power and energy. The efficiency of the process of vibration-based purification of crude glycerol was evaluated on such parameters as vibration control, angular rate of flow, rate of temperature. The recommendations of the second basic parameters of the lateral period were determined in accordance with the second set of the second order. Analyzing the results of studies of vibration-centrifugal separation of liquid inhomogeneous raw materials, it can be argued that the most influential factors in the separation of these products are the rotor speed, vibration shaft speed, oscillation amplitude, power, temperature and processing time.


2020 ◽  
Vol 50 (1) ◽  
pp. 79-86
Author(s):  
Elena Verboloz ◽  
Marina Ivanova ◽  
Vera Demchenko ◽  
Sergey Fartukov ◽  
Nikita Evona

Introduction. Rose hips are rich in macro- and micronutrients. Unfortunately, heat treatment destroys most nutrients. Ultrasonic technologies make it possible to reduce the drying time and lower the temperature regime. The research objective was to adjust ultrasound technology to rose hip production in order to reduce the loss of vitamins and improve the quality indicators of the dried product. Study objects and methods. The research featured rose hips of the Rosa canina species collected in the south of Kazakhstan. This subspecies of wild rose is poor in vitamin C. Nevertheless, this shrub is extremely common in Russia and other countries of the Commonwealth of Independent States. The raw material was dried according to standard methods. One group of samples was treated with ultrasound, while the other served as control. Both groups underwent a sensory evaluation and were tested for moisture and vitamin C. Results and discussion. The rose hips were dried in a combination steam oven with a built-in ultrasonic wave generator. The research revealed the following optimal parameters of the ultrasound drying process: frequency of ultrasonic vibrations – 22 kHz, processing time – 2.5 h, temperature in the combination steam oven – +56°C, initial moisture content – 30%. The resulting product met the requirements of State Standard. The loss of moisture was 57%. According to State Standard 1994-93, the initial moisture content should be 15% or less. Time decreased from 360 min to 160 min, and the initial moisture was 13%. The experiment confirmed the initial hypothesis that ultrasonic treatment improves the drying process by improving quality indicators and preserving vitamin C in raw materials using. Conclusion. Ultrasound treatment during moisture removal from rose hips provides a resource-saving technology that fulfills an economically and socially important function.


2020 ◽  
Vol 1 (27(54)) ◽  
pp. 8-11
Author(s):  
A.D. Dzhamakeeva

The work is devoted to the study of the possibility of using functional vegetable ingredients in the technology of meatsemi-finished products andthe study of their influence on the functional and technological properties of chopped mea, and nutritional value of finished products. The modeling and optimization of the meat-vegetable semi-finished products recipes was carried out using the Smart Lab program. The quality indicators of finished products, confirming the feasibility of introducing vegetable raw materials into the recipes of semi-finished product, were investigated. The proposed technologies of the meat-vegetablesemi-finished products hasbeen tested at the meat-processing enterprise «Barkad»


Sign in / Sign up

Export Citation Format

Share Document