scholarly journals On-chip ZnO nanofibers prepared by electrospinning method for NO2 gas detection

2018 ◽  
Vol 27 (4) ◽  
pp. 317 ◽  
Author(s):  
Van Hoang Nguyen ◽  
Van Dung Nguyen ◽  
Quang Dat Do ◽  
Thi Minh Nguyet Quan ◽  
Manh Hung Chu ◽  
...  
Keyword(s):  
Gas Sensing ◽  
Hexagonal Wurtzite Structure ◽  
X Ray Diffraction ◽  
Electrospinning Technique ◽  
X Ray ◽  
Electrospinning Method ◽  
Resistance Modulation ◽  
Zno Nanofibers ◽  
On Chip ◽  
Gas Response

In the present study, on-chip ZnO nanofibers were fabricated by means of the electrospinning technique followed by a calcination process at 600 oC towards the gas sensor application. The morphology, composition, and crystalline structure of the as-spun and annealed ZnO nanofibers were investigated by field emission scanning electron microscopy (FESEM), energy dispersive X-ray (EDX), and X-ray diffraction (XRD), respectively. The findings show that spider-net like ZnO nanofibers with a diameter of 60 – 100 nm were successfully synthesized without any incorporation of impurities into the nanofibers. The FESEM images also reveal that each nanofiber is composed of many nanograins. The combination of experimental and calculated X-ray diffraction data indicate that ZnO nanofibers were crystallized in hexagonal wurtzite structure. For the gas sensing device application, the ZnO nanofibers-based sensors were tested with the nitrogen dioxide gas in the temperature range of 200 oC to 350 oC and concentrations from 2.5 ppm to 10 ppm. The sensing property results indicate that at the optimal working temperature of 300 oC, the ZnO nanofibers-based sensors exhibited a maximum response of 30 and 166 times on exposure of 2.5 and 10 ppm NO2 gas, respectively. The presence of nanograins within nanofibers, which results in further intensification of the resistance modulation, is responsible for such high gas response.

Method for synthesizing ZnO of different nanostructures by electrospinning and study of their gas sensing properties

2019 ◽  
Vol 33 (25) ◽  
pp. 1950297
Author(s):  
Xiang-Bing Li ◽  
Shu-Yi Ma ◽  
Fu-Rong Li ◽  
Yu-Xiang Zhao ◽  
Xiao-Bin Liu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Gas Sensing ◽  
Component Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electrospinning Method ◽  
Gas Sensing Properties ◽  
Zno Nanofibers ◽  
Scanning Electron

The properties of nanomaterials usually depend on their microstructures, the same material of different microstructures could be used for various applications. However, most devices could only synthesize a single microstructure, so it is meaningful that the different microstructures were synthesized by one method. In our study, electrospinning was applied to fabricate ZnO nanofibers and nanoparticles. In this approach, Zn(Ac)/PVP composite fibers of different component ratio were synthesized by electrospinning method which was subsequently calcined and formed ZnO nanofibers and nanoparticles. The microstructure, chemical composition and gas sensing were investigated with scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and WS-60A gas sensing measurement system. The synthesis mechanisms of ZnO nanofibers and nanoparticles were discussed in detail.

A Novel Tungsten Trioxide Based Gas Sensor for Indoor Formaldehyde Detection

2021 ◽  
Vol 16 (3) ◽  
pp. 363-367
Author(s):  
Gaoqi Zhang ◽  
Fan Zhang ◽  
Kaifang Wang ◽  
Tao Tian ◽  
Shanyu Liu ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Gas Sensor ◽  
Indoor Air ◽  
Gas Sensing ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sensing Material ◽  
Transmission Electron ◽  
Gas Sensing Properties ◽  
Gas Response

Accurate and real-time detection of formaldehyde (HCHO) in indoor air is urgently needed for human health. In this work, a ceramic material (WO3·H2O) with unique structure was successfully prepared using an efficient hydrothermal method. The crystallinity, morphology and microstructure of the as-prepared sensing material were analyzed by X-ray diffraction (XRD), field emission scanning electron microscope (FESEM) as well as transmission electron microscope (TEM). The characterization results suggest that the as-prepared sample is composed of square-like nanoplates with uneven surface. Formaldehyde vapor is utilized as the target gas to investigate gas sensing properties of the synthesized novel nanoplates. The testing results indicate that the as-fabricated gas sensor exhibit high gas response and excellent repeatability to HCHO gas. The response value (Ra/Rg) is 24.5 towards 70 ppm HCHO gas at 350 °C. Besides, the gas sensing mechanism was described.

Methanol Sensing Properties of Electrospun SnO2 -ZnO Nanofibers

2011 ◽  
Vol 356-360 ◽  
pp. 565-568
Author(s):  
Shao Hong Wei ◽  
Mei Hua Zhou ◽  
Wei Ping Du
Keyword(s):  
Electron Microscopy ◽  
X Ray Diffraction ◽  
Promoting Effect ◽  
Heterojunction Structure ◽  
X Ray ◽  
Sensing Properties ◽  
Transmission Electron ◽  
Electrospinning Method ◽  
Zno Nanofibers ◽  
Scanning Electron

Pure ZnO and SnO2-ZnO nanofibers were synthesized by electrospinning method and characterized via X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The structure and methanol sensing properties of these fibers were investigated. The results indicate that the 20 wt% SnO2-ZnO sensor exhibits considerable sensitivity, rapid response, and good selectivity against methanol at 200 °C due to the special 1D fibers properties and the promoting effect of SnO2/ZnO heterojunction structure. The methanol sensing mechanism of SnO2-ZnO nanofibers were also discussed.

scholarly journals Sputtered SnO2/ZnO Heterostructures for Improved NO2 Gas Sensing Properties

Chemosensors ◽  
2020 ◽  
Vol 8 (3) ◽  
pp. 67 ◽  
Author(s):  
Bharat Sharma ◽  
Ashutosh Sharma ◽  
Monika Joshi ◽  
Jae-ha Myung
Keyword(s):  
Photoelectron Spectroscopy ◽  
Gas Sensing ◽  
Operating Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Response Recovery ◽  
No2 Gas Sensor ◽  
Highly Sensitive ◽  
Gas Sensing Properties ◽  
Gas Response

A highly sensitive and selective NO2 gas sensor dependent on SnO2/ZnO heterostructures was fabricated using a sputtering process. The SnO2/ZnO heterostructure thin film samples were characterized by field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), Energy-dispersive X-ray spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS). Sensors fabricated with heterostructures attained higher gas response (S = 66.9) and quicker response-recovery (20 s, 45 s) characteristics at 100 °C operating temperature towards 100 ppm NO2 gas efficiently in comparison to sensors based on their mono-counterparts. The selectivity and stability of SnO2/ZnO heterostructures were studied. The more desirable sensing mechanism of SnO2/ZnO heterostructures towards NO2 was described in detail.

Fabrication and optical properties of NiO/ZnO hierarchical nanostructures

2021 ◽  
Vol 15 (1) ◽  
pp. 45-50
Author(s):  
Minh Vuong Nguyen ◽  
◽  
Ngoc Khoa Truong Nguyen ◽  
Keyword(s):  
Open Space ◽  
Visible Region ◽  
Hexagonal Structure ◽  
Nio Nanoparticles ◽  
X Ray Diffraction ◽  
Energy Dispersion Spectroscopy ◽  
Hierarchical Nanostructures ◽  
X Ray ◽  
Electrospinning Method ◽  
Zno Nanofibers

NiO/ZnO hierarchical nanostructures were synthesized by a combination of electrospinning, hydrothermal and ultraviolet (UV)-assisted deposition. Initially, ZnO nanofibers were synthesized by electrospinning method following thermal oxidation. Subsequently, ZnO hierarchical nanostructures were synthesized by hydrothermal method using ZnO nanofibers as templates. Finally, NiO nanoparticles were deposited on ZnO surface by UV-assisted deposition method. Morphology and characteristics of the material were determined by scanning electron microscopy (SEM), energy dispersion spectroscopy (EDS), X-ray diffraction (XRD), X-ray photoelectron spectrum (XPS) and photoluminescence spectrum (PL). The results showed that the NiO/ZnO hierarchical nanostructures with high open space were obtained. NiO/ZnO crystals showed hexagonal structure of ZnO without phase formation of NiO. PL spectra of the NiO/ZnO material showed emission peaks shift towards longer wavelengths in the visible region with increasing the content of NiO nanoparticles.

The Influence of Formula and Process on Physical Properties and the Release Profile of PVA/BSA Nanofibers Formed by Electrospinning Technique

2015 ◽  
Vol 31 ◽  
pp. 103-116 ◽  
Author(s):  
Chandra Risdian ◽  
Muhamad Nasir ◽  
Annisa Rahma ◽  
Heni Rachmawati
Keyword(s):  
Dip Coating ◽  
Differential Scanning Calorimetric ◽  
X Ray Diffraction ◽  
Successful Development ◽  
Electrospinning Technique ◽  
X Ray ◽  
Fourier Transformed Infrared Spectroscopy ◽  
Electrospinning Method ◽  
Coating Method ◽  
Dip Coating Method

Electrospinning is a simple versatile process to produce nanofibers. However, it requires careful approach to form appropriates fibers for different purposes. This report describes aspects influencing successful development of nanofiber containing BSA using electrospinning method. Optical and scanning electron microscopy, energy dispersive X-Ray and Fourier transformed infrared spectroscopy, differential scanning calorimetric, and X-Ray diffraction analysis of nanofiber were performed. Modification of PVA/BSA nanofiber with Eudragit L-100 was conducted by dip coating method. The presence of BSA increased the diameter of the fibers. Modification of PVA/BSA nanofiber with Eudragit L-100 delayed the release of BSA in acidic medium but promoting its release in intestinal mimicking medium.

scholarly journals Effect of Growth Temperature and Time on Morphology and Gas Sensitivity of Cu2O/Cu Microstructures

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Ling Wu ◽  
Lun Zhang ◽  
Zhipeng Xun ◽  
Guili Yu ◽  
Liwei Shi
Keyword(s):  
Electron Microscopy ◽  
Gas Sensors ◽  
Gas Sensing ◽  
Spherical Particles ◽  
X Ray Diffraction ◽  
Gas Sensitivity ◽  
X Ray ◽  
Transmission Electron ◽  
Wide Range ◽  
Gas Response

A facile hydrothermal synthesis with CuSO4as the copper source was used to prepare micro/nano-Cu2O. The obtained samples have been characterized by X-ray diffraction, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). With increasing the reaction temperature and time, the final products were successively Cu2O octahedron microcrystals, Cu2O/Cu composite particles, and a wide range of Cu spherical particles. The gas sensitivity of products towards ethanol and acetone gases was studied. The results showed that sensors prepared with Cu2O/Cu composites synthesized at 65°C for 15 min exhibited optimal gas sensitivity. The gas sensing mechanism and the effect of Cu in the enhanced gas response were also elaborated. The excellent gas sensitivity indicates that Cu2O/Cu composites have potential application as gas sensors.

scholarly journals Synthesis of CuO by Electrospinning Method for Sensing of Hydrogen and Carbon Monoxide Gases

2021 ◽  
Vol 68 (4) ◽  
pp. 945-954
Author(s):  
Abdollah Fallah Shojaei ◽  
Parisa Fallah Komsari
Keyword(s):  
Carbon Monoxide ◽  
Gas Sensing ◽  
Operating Temperature ◽  
Particle Morphology ◽  
Fast Response ◽  
X Ray Diffraction ◽  
Sem Images ◽  
X Ray ◽  
Electrospinning Method ◽  
Response And Recovery

The pure CuO nanofibers were synthesized via the electrospinning method successfully. The calcinated CuO nanofibers were investigated for sensing hydrogen and carbon monoxide gases. Structural properties of the synthesized calcinated nanofibers were studied using Fourier –transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Energy-dispersive X-ray spectroscopy (EDX), and particle morphology by scanning electron microscopy (SEM). SEM images confirmed string-like structures, nanofibers. The sensor based on the calcinated CuO nanofibers exhibited excellent gas sensing performance at the low operating temperature of 175 °C and the fast response and recovery characteristics at a low concentration. Moreover, good stability, prominent reproducibility, and excellent selectivity are also observed based on the calcinated nanofibers. These results demonstrate the potential application of calcinated CuO nanofibers for sensing hydrogen (10–200 ppm) and carbon monoxide (400–700 ppm) gases.

scholarly journals Studies on Spray Pyrolised Nanostructured SnO2 Thin Films for H2 Gas Sensing Application

2014 ◽  
Vol 36 ◽  
pp. 125-141 ◽  
Author(s):  
R.H. Bari ◽  
S.B. Patil
Keyword(s):  
Thin Films ◽  
Gas Sensing ◽  
Spray Pyrolysis Technique ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sensing System ◽  
Gas Sensing Properties ◽  
Structural Surface ◽  
Diffraction Peaks ◽  
Gas Response

The objective of this work is to study the influence of pyrolysis temperature on structural, surface morphology and gas sensing properties of the nanostructured SnO2 thin films prepared by spray pyrolysis technique. These films were characterized for the structural, morphological and elemental composition carried by means of X-ray diffraction (XRD), scanning electron mi­croscopy (SEM) and energy dispersive spectrophotometer (EDAX). The information of crystallite size, dislocation density and microstrain is obtained from the full width-at half- maximum (FWHM) of the diffraction peaks. Effect of sprayed deposition temperature on H2 gas sensing performance and electrical properties were studied using static gas sensing system. The sensor (Tpyr. = 350°C) showed high gas response (S = 1200 at 350 °C) on exposure of 500 ppm of H2 and high selectivity against other gases The results are discussed and interpreted.

Hydrothermal Synthesis and Gas Sensing Properties of α-Fe2O3 Hollow Microspheres and Nanorods

2011 ◽  
Vol 343-344 ◽  
pp. 177-180
Author(s):  
Xia Lei Ye ◽  
Guo Han Liu ◽  
Yu Zhe Song ◽  
Gen Liang Han ◽  
Qi Hai Lu ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Hydrothermal Synthesis ◽  
Gas Sensing ◽  
Ethylenediaminetetraacetic Acid ◽  
Hollow Microspheres ◽  
X Ray Diffraction ◽  
X Ray ◽  
Gas Sensing Properties ◽  
Gas Response ◽  
Scanning Electron

α-Fe2O3 hollow microspheres and nanorods were synthesized via a hydrothermal method using glucose and ethylenediaminetetraacetic acid (EDTA) as morphology controlled agents, followed by calcination at 500 °C for 4 h in air. The crystal structures of products were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). The results show that the hollow microspheres with diameters of 1-2 μm are consist of nanoparticles (80-100 nm), and the nanorods have a structure in the diameter of 80-100 nm and length about 1 μm. Furthermore, the α-Fe2O3 hollow microspheres show higher gas response to ethanol than that of nanorods and nanoparticles.

Sign in / Sign up

Export Citation Format

Share Document