scholarly journals Studies on Spray Pyrolised Nanostructured SnO2 Thin Films for H2 Gas Sensing Application

2014 ◽  
Vol 36 ◽  
pp. 125-141 ◽  
Author(s):  
R.H. Bari ◽  
S.B. Patil
Keyword(s):  
Thin Films ◽  
Gas Sensing ◽  
Spray Pyrolysis Technique ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sensing System ◽  
Gas Sensing Properties ◽  
Structural Surface ◽  
Diffraction Peaks ◽  
Gas Response

The objective of this work is to study the influence of pyrolysis temperature on structural, surface morphology and gas sensing properties of the nanostructured SnO2 thin films prepared by spray pyrolysis technique. These films were characterized for the structural, morphological and elemental composition carried by means of X-ray diffraction (XRD), scanning electron mi­croscopy (SEM) and energy dispersive spectrophotometer (EDAX). The information of crystallite size, dislocation density and microstrain is obtained from the full width-at half- maximum (FWHM) of the diffraction peaks. Effect of sprayed deposition temperature on H2 gas sensing performance and electrical properties were studied using static gas sensing system. The sensor (Tpyr. = 350°C) showed high gas response (S = 1200 at 350 °C) on exposure of 500 ppm of H2 and high selectivity against other gases The results are discussed and interpreted.

A Novel Tungsten Trioxide Based Gas Sensor for Indoor Formaldehyde Detection

2021 ◽  
Vol 16 (3) ◽  
pp. 363-367
Author(s):  
Gaoqi Zhang ◽  
Fan Zhang ◽  
Kaifang Wang ◽  
Tao Tian ◽  
Shanyu Liu ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Gas Sensor ◽  
Indoor Air ◽  
Gas Sensing ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sensing Material ◽  
Transmission Electron ◽  
Gas Sensing Properties ◽  
Gas Response

Accurate and real-time detection of formaldehyde (HCHO) in indoor air is urgently needed for human health. In this work, a ceramic material (WO3·H2O) with unique structure was successfully prepared using an efficient hydrothermal method. The crystallinity, morphology and microstructure of the as-prepared sensing material were analyzed by X-ray diffraction (XRD), field emission scanning electron microscope (FESEM) as well as transmission electron microscope (TEM). The characterization results suggest that the as-prepared sample is composed of square-like nanoplates with uneven surface. Formaldehyde vapor is utilized as the target gas to investigate gas sensing properties of the synthesized novel nanoplates. The testing results indicate that the as-fabricated gas sensor exhibit high gas response and excellent repeatability to HCHO gas. The response value (Ra/Rg) is 24.5 towards 70 ppm HCHO gas at 350 °C. Besides, the gas sensing mechanism was described.

scholarly journals Annealing-Driven Microstructural Evolution and Its Effects on the Surface and Nanomechanical Properties of Cu-Doped NiO Thin Films

Coatings ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 107 ◽  
Author(s):  
San-Ho Wang ◽  
Sheng-Rui Jian ◽  
Guo-Ju Chen ◽  
Huy-Zu Cheng ◽  
Jenh-Yih Juang
Keyword(s):  
Thin Films ◽  
Photoelectron Spectroscopy ◽  
Annealing Temperature ◽  
Film Surface ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nanomechanical Properties ◽  
Glass Substrates ◽  
Structural Surface ◽  
Diffraction Peaks

The effects of annealing temperature on the structural, surface morphological and nanomechanical properties of Cu-doped (Cu-10 at %) NiO thin films grown on glass substrates by radio-frequency magnetron sputtering are investigated in this study. The X-ray diffraction (XRD) results indicated that the as-deposited Cu-doped NiO (CNO) thin films predominantly consisted of highly defective (200)-oriented grains, as revealed by the broadened diffraction peaks. Progressively increasing the annealing temperature from 300 to 500 °C appeared to drive the films into a more equiaxed polycrystalline structure with enhanced film crystallinity, as manifested by the increased intensities and narrower peak widths of (111), (200) and even (220) diffraction peaks. The changes in the film microstructure appeared to result in significant effects on the surface energy, in particular the wettability of the films as revealed by the X-ray photoelectron spectroscopy and the contact angle of the water droplets on the film surface. The nanoindentation tests further revealed that both the hardness and Young’s modulus of the CNO thin films increased with the annealing temperature, suggesting that the strain state and/or grain boundaries may have played a prominent role in determining the film’s nanomechanical characterizations.

scholarly journals Sputtered SnO2/ZnO Heterostructures for Improved NO2 Gas Sensing Properties

Chemosensors ◽  
2020 ◽  
Vol 8 (3) ◽  
pp. 67 ◽  
Author(s):  
Bharat Sharma ◽  
Ashutosh Sharma ◽  
Monika Joshi ◽  
Jae-ha Myung
Keyword(s):  
Photoelectron Spectroscopy ◽  
Gas Sensing ◽  
Operating Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Response Recovery ◽  
No2 Gas Sensor ◽  
Highly Sensitive ◽  
Gas Sensing Properties ◽  
Gas Response

A highly sensitive and selective NO2 gas sensor dependent on SnO2/ZnO heterostructures was fabricated using a sputtering process. The SnO2/ZnO heterostructure thin film samples were characterized by field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), Energy-dispersive X-ray spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS). Sensors fabricated with heterostructures attained higher gas response (S = 66.9) and quicker response-recovery (20 s, 45 s) characteristics at 100 °C operating temperature towards 100 ppm NO2 gas efficiently in comparison to sensors based on their mono-counterparts. The selectivity and stability of SnO2/ZnO heterostructures were studied. The more desirable sensing mechanism of SnO2/ZnO heterostructures towards NO2 was described in detail.

Mo-W-O thin films for CO sensing

2000 ◽  
Vol 638 ◽  
Author(s):  
Elisabetta Comini ◽  
Matteo Ferroni ◽  
Vincenzo Guidi ◽  
Giuliano Martinelli ◽  
Michele Sacerdoti ◽  
...  
Keyword(s):  
Thin Films ◽  
Gas Sensing ◽  
Weight Ratio ◽  
X Ray Diffraction ◽  
Composite Target ◽  
X Ray ◽  
Structural Characterisation ◽  
Gas Sensing Properties ◽  
Recovery Times ◽  
Response And Recovery

AbstractThe Mo-W-O thin films were deposited by RF reactive sputtering from composite target of W and Mo (20:80 weight ratio). Structural characterisation was carried out by X-ray diffraction spectroscopy and the composition of the film was obtained by Rutherford backscattering analysis. The layers were investigated by volt-amperometric technique for electrical and gas-sensing properties. The films were capable of sensing CO. No effect of poisoning of the surface was recorded and recovery of the resistance was complete. A concentration of CO as low as 15 ppm produced a relative variation in the conductance of 390% with response and recovery times of about 2 minutes at a working temperature of 200°C.

Low-Temperature Synthesis and Gas Sensing Properties of Anatase TiO2 Thin Films

2011 ◽  
Vol 492 ◽  
pp. 300-303
Author(s):  
Fu Jian Ren ◽  
Yi Sun ◽  
Liang Huang ◽  
Yun Han Ling ◽  
Jia You Feng
Keyword(s):  
Thin Films ◽  
Deposition Temperature ◽  
Gas Sensing ◽  
X Ray Diffraction ◽  
Sensing Properties ◽  
Force Microscopy ◽  
Glass Substrates ◽  
Atomic Force ◽  
Gas Sensing Properties ◽  
Gas Response

Crystalline anatase TiO2thin films were obtained on glass substrates at 60°C, 75°C and 90°C, respectively, by liquid phase deposition (LPD) method without subsequent heat treatment. X-ray diffraction (XRD), atomic force microscopy (AFM) and UV-Vis spectrophotometer were used to characterize the as-synthesized TiO2thin films. The H2sensing properties of the TiO2thin films based sensors were investigated. The results show that the gas sensors signal Ra/Rg (Ra: resistance in air, Rg: resistance in a sample gas) decreases with the increasing deposition temperature. The TiO2thin films obtained at deposition temperature of 60°C exhibited the maximum H2gas response at 350°C, and the magnitude of the sensor signal and the response time for 500ppm H2was 1.25 and 17s, respectively.

Hydrothermal Synthesis and Gas Sensing Properties of α-Fe2O3 Hollow Microspheres and Nanorods

2011 ◽  
Vol 343-344 ◽  
pp. 177-180
Author(s):  
Xia Lei Ye ◽  
Guo Han Liu ◽  
Yu Zhe Song ◽  
Gen Liang Han ◽  
Qi Hai Lu ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Hydrothermal Synthesis ◽  
Gas Sensing ◽  
Ethylenediaminetetraacetic Acid ◽  
Hollow Microspheres ◽  
X Ray Diffraction ◽  
X Ray ◽  
Gas Sensing Properties ◽  
Gas Response ◽  
Scanning Electron

α-Fe2O3 hollow microspheres and nanorods were synthesized via a hydrothermal method using glucose and ethylenediaminetetraacetic acid (EDTA) as morphology controlled agents, followed by calcination at 500 °C for 4 h in air. The crystal structures of products were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). The results show that the hollow microspheres with diameters of 1-2 μm are consist of nanoparticles (80-100 nm), and the nanorods have a structure in the diameter of 80-100 nm and length about 1 μm. Furthermore, the α-Fe2O3 hollow microspheres show higher gas response to ethanol than that of nanorods and nanoparticles.

Preparation and Gas Sensing Properties of Hierarchical Flower-Shaped Bi2WO6

2016 ◽  
Vol 69 (1) ◽  
pp. 107 ◽  
Author(s):  
Jingkun Xiao ◽  
Chengwen Song ◽  
Wei Dong ◽  
Yanyan Yin ◽  
Chen Li
Keyword(s):  
Photoelectron Spectroscopy ◽  
Gas Sensing ◽  
Fast Response ◽  
X Ray Diffraction ◽  
Fast Recovery ◽  
X Ray ◽  
Sensing Properties ◽  
Sensing System ◽  
Gas Sensing Properties ◽  
20 Nm

Hierarchical flower-shaped Bi2WO6 was obtained by a simple hydrothermal method. Morphology and structure of the Bi2WO6 were characterised by single electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and N2 adsorption techniques. Gas sensing properties of the Bi2WO6 sensor were investigated by a static gas-sensing system. The results show the as-synthesised flower-shaped product is pure orthorhombic Bi2WO6, which is composed of nanosheets with ~10–20 nm in thickness and hundreds of nanometres in planar size. At this optimal operating temperature of 300°C, the Bi2WO6 sensor exhibits ultra-fast response (1-2 s) and fast recovery time (6–12 s) towards ethanol detection, and high selectivity to other gases such as methanol, benzene, dichloromethane, and hexane.

Polyaniline/SnO2 Nanocomposite Sensor for NO2 Gas Sensing at Low Operating Temperature

2015 ◽  
Vol 14 (04) ◽  
pp. 1550011 ◽  
Author(s):  
A. Sharma ◽  
M. Tomar ◽  
V. Gupta ◽  
A. Badola ◽  
N. Goswami
Keyword(s):  
Thin Films ◽  
Gas Sensing ◽  
High Sensitivity ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
Chemical Route ◽  
Sensing Properties ◽  
Response Recovery ◽  
Transmission Electron ◽  
Gas Sensing Properties

In this paper gas sensing properties of 0.5–3% polyaniline (PAni) doped SnO 2 thin films sensors prepared by chemical route have been studied towards the trace level detection of NO 2 gas. The structural, optical and surface morphological properties of the PAni doped SnO 2 thin films were investigated by performing X-ray diffraction (XRD), Transmission electron microscopy (TEM) and Raman spectroscopy measurements. A good correlation has been identified between the microstructural and gas sensing properties of these prepared sensors. Out of these films, 1% PAni doped SnO 2 sensor showed high sensitivity towards NO 2 gas along with a sensitivity of 3.01 × 102 at 40°C for 10 ppm of gas. On exposure to NO 2 gas, resistance of all sensors increased to a large extent, even greater than three orders of magnitude. These changes in resistance upon removal of NO 2 gas are found to be reversible in nature and the prepared composite film sensors showed good sensitivity with relatively faster response/recovery speeds.

scholarly journals Chemically synthesized PbS Nano particulate thin films for a rapid NO2 gas sensor

2016 ◽  
Vol 34 (1) ◽  
pp. 204-211 ◽  
Author(s):  
Vishal V. Burungale ◽  
Rupesh S. Devan ◽  
Sachin A. Pawar ◽  
Namdev S. Harale ◽  
Vithoba L. Patil ◽  
...  
Keyword(s):  
Thin Films ◽  
Gas Sensor ◽  
Gas Sensing ◽  
Operating Temperature ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
Gas Sensitivity ◽  
Silar Method ◽  
Layer Adsorption ◽  
Gas Sensing Properties

AbstractRapid NO2 gas sensor has been developed based on PbS nanoparticulate thin films synthesized by Successive Ionic Layer Adsorption and Reaction (SILAR) method at different precursor concentrations. The structural and morphological properties were investigated by means of X-ray diffraction and field emission scanning electron microscope. NO2 gas sensing properties of PbS thin films deposited at different concentrations were tested. PbS film with 0.25 M precursor concentration showed the highest sensitivity. In order to optimize the operating temperature, the sensitivity of the sensor to 50 ppm NO2 gas was measured at different operating temperatures, from 50 to 200 °C. The gas sensitivity increased with an increase in operating temperature and achieved the maximum value at 150 °C, followed by a decrease in sensitivity with further increase of the operating temperature. The sensitivity was about 35 % for 50 ppm NO2 at 150 °C with rapid response time of 6 s. T90 and T10 recovery time was 97 s at this gas concentration.

X-ray Line Broadening Analysis of Tl-Superconducting Films

1989 ◽  
Vol 33 ◽  
pp. 145-151
Author(s):  
M. O. Eatough ◽  
D. S. Ginley ◽  
B. Morosin
Keyword(s):  
Thin Films ◽  
Superconducting Films ◽  
Electron Beam Evaporation ◽  
Superconducting Thin Films ◽  
Line Broadening ◽  
X Ray Diffraction ◽  
X Ray ◽  
Current Densities ◽  
Diffraction Peaks ◽  
Sequential Electron

AbstractSuperconducting thin films (0.3-0.7μm) in the TI-Ca-Ba-Cu-0 system have been prepared on various single crystal substrates by sequential electron beam evaporation followed by appropriate sintering and annealing. Oxygen-annealed films show Tc as high as 110K and critical current densities to 600,000 A/cm2. X-ray diffraction analyses of these films show predominantly the Tl2Ca2Ba2Cu2O10 phase (c-parameter near 36Å), but some also contain up to 50 at% of the Tl2CaBa2Cu2O8 phase (c-parameter near 30Å). The complete absence of hkl reflections other than 00I demonstrates the highly oriented nature of the films as well as the absence of other Tl phases. The diffraction peaks are noticeably broader for the 36Å phase than for the 30Å phase. For a 0.7μm film such broadening is consistent with coherent sizes along the c-axis of 1200 - 1400Å and 500Å, respectively, for the 30Å and 36Å phases, and of strain values near 1.4-1.8 x 10-3 for both phases.

Sign in / Sign up

Export Citation Format

Share Document