Current state of K-based geopolymer cements cured at ambient temperature

2015 ◽  
Vol 4 (1) ◽  
pp. 125-129 ◽  
Author(s):  
Rishi Gupta ◽  
Harsh M. Rathod
Keyword(s):  
Ambient Temperature ◽  
Current State ◽  
Geopolymer Cements

scholarly journals Complex Maturity Method for Estimating the Concrete Strength Based on Curing Temperature, Ambient Temperature and Relative Humidity

2021 ◽  
Vol 11 (16) ◽  
pp. 7712
Author(s):  
Yelbek Utepov ◽  
Aleksej Aniskin ◽  
Assel Tulebekova ◽  
Aliya Aldungarova ◽  
Shyngys Zharassov ◽  
...  
Keyword(s):  
Relative Humidity ◽  
Ambient Temperature ◽  
Concrete Strength ◽  
Economic Effect ◽  
Curing Temperature ◽  
Coefficient Of Determination ◽  
Complex Method ◽  
Current State ◽  
Maturity Method ◽  
Calibration Dependence

The maturity method is deservedly considered one of the reliable indirect methods for determining the strength at the early stages of concrete curing. The main parameter in the calculation is the internal temperature of concrete that accumulates during the chemical reaction of concrete curing, while external factors such as ambient temperature and relative humidity are fallaciously omitted. In this work, the complex maturity method was developed based on ASTM C1074, accounting for the influence of ambient temperature and relative humidity and coefficients indicating their influence weight. The laboratory testing to measure the concrete strength by compression method and non-destructive sclerometer method were performed on concrete samples according to ASTM C109, GOST 22690, and GOST 10180. According to the calibration dependence of the existing and proposed methods results in comparison with the strength of cubic samples, the highest coefficient of determination R2 = 0.976 was revealed for the complex method of maturity, which indicates its reliability in contrast with sclerometer and traditional maturity methods. The determination of complex maturity allows for an evaluation of the current state of concrete strength, but also reduces the waiting time for concrete curing and increases the economic effect during construction.

Volcanic ash-based geopolymer cements/concretes: the current state of the art and perspectives

2016 ◽  
Vol 24 (5) ◽  
pp. 4433-4446 ◽  
Author(s):  
Jean Noël Yankwa Djobo ◽  
Antoine Elimbi ◽  
Hervé Kouamo Tchakouté ◽  
Sanjay Kumar
Keyword(s):  
Volcanic Ash ◽  
State Of The Art ◽  
Current State ◽  
Geopolymer Cements

SEM of non-coated hepatocellular cytoskeleton of perfused livers

1984 ◽  
Vol 42 ◽  
pp. 306-307
Author(s):  
S.W. French ◽  
N.C. Benson ◽  
C. Davis-Scibienski
Keyword(s):  
Ambient Temperature ◽  
Critical Point ◽  
Protease Inhibitors ◽  
Metal Deposition ◽  
Heat Damage ◽  
Detergent Extraction ◽  
Cytoskeletal Elements ◽  
Triton X ◽  
Excised Tissue

Previous SEM studies of liver cytoskeletal elements have encountered technical difficulties such as variable metal coating and heat damage which occurs during metal deposition. The majority of studies involving evaluation of the cell cytoskeleton have been limited to cells which could be isolated, maintained in culture as a monolayer and thus easily extracted. Detergent extraction of excised tissue by immersion has often been unsatisfactory beyond the depth of several cells. These disadvantages have been avoided in the present study. Whole C3H mouse livers were perfused in situ with 0.5% Triton X-100 in a modified Jahn's buffer including protease inhibitors. Perfusion was continued for 1 to 2 hours at ambient temperature. The liver was then perfused with a 2% buffered gluteraldehyde solution. Liver samples including spontaneous tumors were then maintained in buffered gluteraldehyde for 2 hours. Samples were processed for SEM and TEM using the modified thicarbohydrazide procedure of Malich and Wilson, cryofractured, and critical point dried (CPD). Some samples were mechanically fractured after CPD.

Formation of Dislocation Channels in Neutron Irradiated Molybdenum

1972 ◽  
Vol 30 ◽  
pp. 672-673
Author(s):  
S. Mahajan
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Ambient Temperature ◽  
Room Temperature ◽  
Channel Formation ◽  
Early Stages ◽  
Transmission Electron ◽  
Three Stages ◽  
Two Stages ◽  
Polycrystalline Molybdenum

The evolution of dislocation channels in irradiated metals during deformation can be envisaged to occur in three stages: (i) formation of embryonic cluster free regions, (ii) growth of these regions into microscopically observable channels and (iii) termination of their growth due to the accumulation of dislocation damage. The first two stages are particularly intriguing, and we have attempted to follow the early stages of channel formation in polycrystalline molybdenum, irradiated to 5×1019 n. cm−2 (E > 1 Mev) at the reactor ambient temperature (∼ 60°C), using transmission electron microscopy. The irradiated samples were strained, at room temperature, up to the macroscopic yield point.Figure 1 illustrates the early stages of channel formation. The observations suggest that the cluster free regions, such as A, B and C, form in isolated packets, which could subsequently link-up to evolve a channel.

Crystallographic Characterization of Dislocation Loops in Irradiated Tungsten

1968 ◽  
Vol 26 ◽  
pp. 290-291
Author(s):  
Robert C. Rau
Keyword(s):  
Electron Microscope ◽  
Ambient Temperature ◽  
Dislocation Loops ◽  
Polycrystalline Specimen ◽  
Post Irradiation ◽  
Neutron Fluences

Previous work has shown that post-irradiation annealing, at temperatures near 1100°C, produces resolvable dislocation loops in tungsten irradiated to fast (E > 1 MeV) neutron fluences of about 4 x 1019 n/cm2 or greater. To crystallographically characterize these loops, tilting experiments were carried out in the electron microscope on a polycrystalline specimen which had been irradiated to 1.5 × 1021 n/cm2 at reactor ambient temperature (∼ 70°C), and subseouently annealed for 315 hours at 1100°C. This treatment produced large loops averaging 1000 Å in diameter, as shown in the micrographs of Fig. 1. The orientation of this grain was near (001), and tilting was carried out about axes near [100], [10] and [110].

Voids in Quenched Nickel

1968 ◽  
Vol 26 ◽  
pp. 266-267
Author(s):  
J. J. Laidler
Keyword(s):  
Electron Beam ◽  
Ambient Temperature ◽  
Cooling Rate ◽  
Three Dimensional ◽  
Cooling Curve ◽  
Polycrystalline Nickel ◽  
Quenching Temperature ◽  
Long Tail ◽  
Diffusion Pump

The presence of three-dimensional voids in quenched metals has long been suspected, and voids have indeed been observed directly in a number of metals. These include aluminum, platinum, and copper, silver and gold. Attempts at the production of observable quenched-in defects in nickel have been generally unsuccessful, so the present work was initiated in order to establish the conditions under which such defects may be formed.Electron beam zone-melted polycrystalline nickel foils, 99.997% pure, were quenched from 1420°C in an evacuated chamber into a bath containing a silicone diffusion pump fluid . The pressure in the chamber at the quenching temperature was less than 10-5 Torr . With an oil quench such as this, the cooling rate is approximately 5,000°C/second above 400°C; below 400°C, the cooling curve has a long tail. Therefore, the quenched specimens are aged in place for several seconds at a temperature which continuously approaches the ambient temperature of the system.

ESEM - A multipurpose surface Electron Microscope

1986 ◽  
Vol 44 ◽  
pp. 632-633 ◽  
Author(s):  
G.D. Danilatos
Keyword(s):  
Electron Microscope ◽  
Room Temperature ◽  
Environmental Scanning ◽  
Gas Composition ◽  
Saturated Water Vapor ◽  
Surface Electron ◽  
Current State ◽  
Saturated Water ◽  
New Type ◽  
Temperature And Pressure

Over recent years a new type of electron microscope - the environmental scanning electron microscope (ESEM) - has been developed for the examination of specimen surfaces in the presence of gases. A detailed series of reports on the system has appeared elsewhere. A review summary of the current state and potential of the system is presented here.The gas composition, temperature and pressure can be varied in the specimen chamber of the ESEM. With air, the pressure can be up to one atmosphere (about 1000 mbar). Environments with fully saturated water vapor only at room temperature (20-30 mbar) can be easily maintained whilst liquid water or other solutions, together with uncoated specimens, can be imaged routinely during various applications.

Recent applications of TEM to the study of interfaces

1990 ◽  
Vol 48 (4) ◽  
pp. 308-309
Author(s):  
C. Barry Carter
Keyword(s):  
High Resolution ◽  
Sample Preparation ◽  
Grain Boundaries ◽  
Diffuse Scattering ◽  
Imaging Techniques ◽  
Amorphous Material ◽  
Contrast Imaging ◽  
Current State ◽  
Actual Nature ◽  
High Resolution Images

This paper will review the current state of understanding of interface structure and highlight some of the future needs and problems which must be overcome. The study of this subject can be separated into three different topics: 1) the fundamental electron microscopy aspects, 2) material-specific features of the study and 3) the characteristics of the particular interfaces. The two topics which are relevant to most studies are the choice of imaging techniques and sample preparation. The techniques used to study interfaces in the TEM include high-resolution imaging, conventional diffraction-contrast imaging, and phase-contrast imaging (Fresnel fringe images, diffuse scattering). The material studied affects not only the characteristics of the interfaces (through changes in bonding, etc.) but also the method used for sample preparation which may in turn have a significant affect on the resulting image. Finally, the actual nature and geometry of the interface must be considered. For example, it has become increasingly clear that the plane of the interface is particularly important whenever at least one of the adjoining grains is crystalline.A particularly productive approach to the study of interfaces is to combine different imaging techniques as illustrated in the study of grain boundaries in alumina. In this case, the conventional imaging approach showed that most grain boundaries in ion-thinned samples are grooved at the grain boundary although the extent of this grooving clearly depends on the crystallography of the surface. The use of diffuse scattering (from amorphous regions) gives invaluable information here since it can be used to confirm directly that surface grooving does occur and that the grooves can fill with amorphous material during sample preparation (see Fig. 1). Extensive use of image simulation has shown that, although information concerning the interface can be obtained from Fresnel-fringe images, the introduction of artifacts through sample preparation cannot be lightly ignored. The Fresnel-fringe simulation has been carried out using a commercial multislice program (TEMPAS) which was intended for simulation of high-resolution images.

Proteasome inhibitors as therapeutics

2005 ◽  
Vol 41 ◽  
pp. 205-218
Author(s):  
Constantine S. Mitsiades ◽  
Nicholas Mitsiades ◽  
Teru Hideshima ◽  
Paul G. Richardson ◽  
Kenneth C. Anderson
Keyword(s):  
Multiple Myeloma ◽  
Drug Class ◽  
Proteasome Inhibitors ◽  
Cell Cycle Regulators ◽  
Current State ◽  
Intracellular Mechanism ◽  
Ubiquitin Proteasome ◽  
Proteasome Pathway ◽  
Hodgkin's Lymphomas ◽  
Clinical Research Data

The ubiquitin–proteasome pathway is a principle intracellular mechanism for controlled protein degradation and has recently emerged as an attractive target for anticancer therapies, because of the pleiotropic cell-cycle regulators and modulators of apoptosis that are controlled by proteasome function. In this chapter, we review the current state of the field of proteasome inhibitors and their prototypic member, bortezomib, which was recently approved by the U.S. Food and Drug Administration for the treatment of advanced multiple myeloma. Particular emphasis is placed on the pre-clinical research data that became the basis for eventual clinical applications of proteasome inhibitors, an overview of the clinical development of this exciting drug class in multiple myeloma, and a appraisal of possible uses in other haematological malignancies, such non-Hodgkin's lymphomas.

Behavioral Genetics: Concepts for Research and Practice in Language Development and Disorders

1995 ◽  
Vol 38 (5) ◽  
pp. 1126-1142 ◽  
Author(s):  
Jeffrey W. Gilger
Keyword(s):  
Language Development ◽  
Behavioral Genetics ◽  
State Of The Art ◽  
Genetic Research ◽  
Great Promise ◽  
Behavioral Genetic ◽  
Fine Grained ◽  
Future Goals ◽  
Current State ◽  
Research Designs

This paper is an introduction to behavioral genetics for researchers and practioners in language development and disorders. The specific aims are to illustrate some essential concepts and to show how behavioral genetic research can be applied to the language sciences. Past genetic research on language-related traits has tended to focus on simple etiology (i.e., the heritability or familiality of language skills). The current state of the art, however, suggests that great promise lies in addressing more complex questions through behavioral genetic paradigms. In terms of future goals it is suggested that: (a) more behavioral genetic work of all types should be done—including replications and expansions of preliminary studies already in print; (b) work should focus on fine-grained, theory-based phenotypes with research designs that can address complex questions in language development; and (c) work in this area should utilize a variety of samples and methods (e.g., twin and family samples, heritability and segregation analyses, linkage and association tests, etc.).

Sign in / Sign up

Export Citation Format

Share Document