scholarly journals STUDY OF THE TRANSPARENT ARMOR STRENGTH UNDER A HIGH-SPEED IMPACT OF A CYLINDRICAL IMPACTOR BY COMPUTER MODELING METHOD

2020 ◽  
pp. 69-77
Author(s):  
Nikolay N. BELOV ◽  
◽  
Nikolay T. YUGOV ◽  
Anton Yu. SAMMEL ◽  
Evgeniy Yu. STEPANOV ◽  
...  
Keyword(s):  
High Speed ◽  
Numerical Study ◽  
Advanced Materials ◽  
Polycrystalline Materials ◽  
Software Systems ◽  
Tempered Glass ◽  
High Speed Impact ◽  
Transparent Armor ◽  
Threat Level ◽  
The Impact

When manufacturing transparent multilayer armor of high threat level, the reinforced silicate glass and transparent ceramics with protecting back films are usually used. The hardness of the front layer of the shield should be much higher than that of the impactor. A promising option isthe use of a single leucosapphire crystal. However, due to its high cost and the impossibility of providing large-sized samples, the transparent polycrystalline materials are developed. One of the most advanced materials is ALON, which is close to leucosapphire in strength characteristics. The aim of this work is to develop a mathematical model to calculate the impact interaction of fragmentation elements with transparent armor. The numerical study is carried out using proprietary software systems. Calculations of the high-speed impact of the steel cylindrical impactor are implemented for three types of shields made of transparent armor. The first two-layer target is made of 20 mm thick tempered glass and a 4 mm thick polycarbonate layer. The second and third targets are three-layered. The front layer of the second target is made of ALON, and the spinel is used for the third one. The second and third layers in these targets are made of tempered glass and polycarbonate, respectively. The calculated results show that ALON is the most impact-resistant material, while spinel is a little less resistant.

scholarly journals Modeling of the interaction of the layered barrier with a high-speed fragment

2019 ◽  
Vol 221 ◽  
pp. 01042
Author(s):  
Alexandr Ishchenko ◽  
Nikolay Belov ◽  
Viktor Burkin ◽  
Anton Sammel ◽  
Nikolay Yugov ◽  
...  
Keyword(s):  
High Speed ◽  
Experimental Studies ◽  
Software Systems ◽  
Fracture Mechanisms ◽  
Elasticity Limit ◽  
Transparent Armor ◽  
Initial Stage ◽  
Numerical Research ◽  
Shock Wave Pressure ◽  
The Impact

For the manufacture of transparent armor of high class protection, as a rule, reinforced silicate glasses, as well as transparent ceramics, are used. Since these materials are resiliently brittle, they can be used only in transparent multilayered barriers with protective back films for protection against high-speed fragmentation elements and bullets. Plexiglass or polycarbonate is most often used as the back layer. The barrier’s face layer must have a hardness substantially higher than the hardness of the drummer’s material, and the Hugonievskii elasticity limit must exceed the shock-wave pressure arising at the initial stage in the barrier. The purpose of this paper is to develop a mathematical model that allows, within the framework of a porous elastic-plastic medium with regard to various fracture mechanisms, to calculate the impact interaction of fragmentation elements with transparent armor. Numerical research was conducted with the help of copyright software systems. Experimental studies of the collision of transparent armor with a splinter simulator in the speed range of 1500 ... 2500 m / s were carried out with the use of throwing installations of the NRI AMM TSU.

Experimental Calibration of ISV Damage Model Constants for Pure Copper for High-Speed Impact Simulation

2016 ◽  
Author(s):  
Yangqing Dou ◽  
Yucheng Liu ◽  
Wilburn Whittington ◽  
Jonathan Miller
Keyword(s):  
High Speed ◽  
Impact Analysis ◽  
Split Hopkinson Pressure Bar ◽  
Internal State ◽  
Pure Copper ◽  
Damage Model ◽  
Hopkinson Pressure Bar ◽  
Experimental Calibration ◽  
High Speed Impact ◽  
The Impact

Coefficients and constants of a microstructure-based internal state variable (ISV) plasticity damage model for pure copper have been calibrated and used for damage modeling and simulation. Experimental stress-strain curves obtained from Cu samples at different strain rate and temperature levels provide a benchmark for the calibration work. Instron quasi-static tester and split-Hopkinson pressure bar are used to obtain low-to-high strain rates. Calibration process and techniques are described in this paper. The calibrated material model is used for high-speed impact analysis to predict the impact properties of Cu. In the numerical impact scenario, a 100 mm by 100 mm Cu plate with a thickness of 10 mm will be penetrated by a 50 mm-long Ni rod with a diameter of 10mm. The thickness of 10 mm was selected for the Cu plate so that the Ni-Cu penetration through the thickness can be well observed through the simulations and the effects of the ductility of Cu on its plasticity deformation during the penetration can be displayed. Also, that thickness had been used by some researchers when investigating penetration mechanics of other materials. Therefore the penetration resistance of Cu can be compared to that of other metallic materials based on the simulation results obtained from this study. Through this study, the efficiency of this ISV model in simulating high-speed impact process is verified. Functions and roles of each of material constant in that model are also demonstrated.

Calculation of Transparent Armor Resistance to a High-Speed Impact by a Spherical Projectile

2021 ◽  
Vol 47 (2) ◽  
pp. 130-134
Author(s):  
A. N. Ishchenko ◽  
S. A. Afanas’eva ◽  
N. N. Belov ◽  
V. V. Burkin ◽  
A. S. D’yachkovskii ◽  
...  
Keyword(s):  
High Speed ◽  
High Speed Impact ◽  
Transparent Armor

High-speed impacts of slender bodies into non-smooth, complex fluids

2018 ◽  
Vol 861 ◽  
Author(s):  
Ishan Sharma
Keyword(s):  
Penetration Depth ◽  
High Speed ◽  
Complex Fluids ◽  
Laboratory Data ◽  
Impact Speed ◽  
High Speed Impact ◽  
Smooth Complex ◽  
Theoretical Predictions ◽  
Slender Bodies ◽  
The Impact

We present a simple hydrodynamical model for the high-speed impact of slender bodies into frictional geomaterials such as soils and clays. We model these materials as non-smooth, complex fluids. Our model predicts the evolution of the impactor’s speed and the final penetration depth given the initial impact speed, and the material and geometric parameters of the impactor and the impacted material. As an application, we investigate the impact of deep-penetrating anchors into seabeds. Our theoretical predictions are found to match field and laboratory data very well.

scholarly journals Effect of different helmet shell configurations on the protection against head trauma

2019 ◽  
Vol 54 (7-8) ◽  
pp. 408-415 ◽  
Author(s):  
Marta Palomar ◽  
Ricardo Belda ◽  
Eugenio Giner
Keyword(s):  
Head Trauma ◽  
High Speed ◽  
Composite Shell ◽  
Human Head ◽  
High Rate ◽  
Finite Element Models ◽  
High Speed Impact ◽  
Full Metal Jacket ◽  
The Impact ◽  
Single Combat

Head trauma following a ballistic impact in a helmeted head is assessed in this work by means of finite element models. Both the helmet and the head models employed were validated against experimental high-rate impact tests in a previous work. Four different composite ply configurations were tested on the helmet shell, and the energy absorption and the injury outcome resulting from a high-speed impact with full metal jacket bullets were computed. Results reveal that hybrid aramid–polyethylene configurations do not prevent bullet penetration at high velocities, while 16-layer aramid configurations are superior in dissipating the energy absorbed from the impact. The fabric orientation of these laminates proved to be determinant for the injury outcome, as maintaining the same orientations for all the layers led to basilar skull fractures (dangerous), while alternating orientation of the adjacent plies resulted in an undamaged skull. To the authors knowledge, no previous work in the literature has analysed numerically the influence of different stack configurations on a single combat helmet composite shell on human head trauma.

Influence of Wave Shape on the Impact of Shallow-Water Waves on Vertical Walls

2006 ◽  
Author(s):  
Claudio Zanzi ◽  
Pablo Go´mez ◽  
Julia´n Palacios ◽  
Joaqui´n Lo´pez ◽  
Julio Herna´ndez
Keyword(s):  
Shallow Water ◽  
Level Set ◽  
Water Waves ◽  
High Speed ◽  
Numerical Study ◽  
Local Level ◽  
Wave Shape ◽  
Shallow Water Waves ◽  
Vertical Walls ◽  
The Impact

A numerical study of the impact of shallow-water waves on vertical walls is presented. The air-liquid flow was simulated using a code for incompressible viscous flow, based on a local level set algorithm and a second-order approximate projection method. The level set transport and reinitialization equations were solved in a narrow band around the interface using an adaptive refined grid. The wave is assumed to be generated by a plunger which is accelerated in an open channel containing water. An arbitrary Lagrangian-Eulerian method was used to take into account the relative movement between the plunger and the end wall of the channel. The evolution of the free surface was visualized using a laser light sheet and a high-speed camera, with a sampling frequency of 1000 Hz. Several simulations were carried out to investigate the influence of the shape of the wave approaching the wall on the relevant quantities associated with the impact. The wave shape just before the impact was changed varying the total length of the channel. The results are compared with experimental results and with results obtained by other authors.

Evaluation of the Impact Formulae for Rigid Projectile Striking on Concrete Target

2011 ◽  
Vol 368-373 ◽  
pp. 894-900 ◽  
Author(s):  
Hao Wu ◽  
Qin Fang
Keyword(s):  
Penetration Depth ◽  
Empirical Formula ◽  
High Strength Concrete ◽  
High Speed ◽  
High Strength ◽  
Local Damage ◽  
High Speed Impact ◽  
Rigid Projectile ◽  
Semi Empirical ◽  
The Impact

Based on the large amounts of field impact tests with different projectile nosed shapes, the abilities of the existing classical empirical and semi-empirical impact formulae in predicting the local damage of normal and high strength concrete targets (NSCT & HSCT) under the strike of rigid projectile were evaluated. It finds that, firstly, for the penetration depth, the Forrestal and Chen & Li semi-empirical formulae, BRL and Whiffen empirical formulae are advised for the NSCT under the impact of ogive nosed projectile; and Chen & Li semi-empirical formula and ACE empirical formulae are advised for the NSCT under the impact of special nosed projectile; the dimensionless penetration depth of NSCT increases linearly with the non-dimensional impact factor. Secondly, for the penetration depth, Chen & Li semi-empirical formula is advised for the HSCT under the mid-to-high speed impact, and the existing formulae are not applicable while the speed of the projectile was relatively low. Thirdly, for the perforation mode of the target, the BRL and Chang empirical formulae are advised for the NSCT, and the Chen semi-empirical formula, ACE and BRL empirical formulae are advised for the HSCT.

High and Low Speed Impact Characteristics of Nanocomposites

2015 ◽  
Vol 1105 ◽  
pp. 62-66 ◽  
Author(s):  
Saud Aldajah ◽  
Yousef Haik ◽  
Kamal Moustafa ◽  
Ammar Alomari
Keyword(s):  
High Speed ◽  
Impact Resistance ◽  
Absorption Capacity ◽  
Impact Testing ◽  
Energy Absorption Capacity ◽  
Low Speed ◽  
High Speed Impact ◽  
Bulletproof Vest ◽  
Impact Characteristics ◽  
The Impact

Nanocomposites attracted the attention of scientists due to their superior mechanical, thermal, chemical and electrical properties. This research studied the impact of adding carbon nanotubes (CNTs) to the woven Kevlar laminated composites on the high and low speed impact characteristics. Different percentages of CNTs were added to the woven Kevlar-Vinylester composite materials. An in-house developed drop weight testing apparatus was utilized for the low speed impact testing. Two different concentrations of the CNTs were added to a 15-layer woven Kevlar laminates, 0.32 wt% and 0.8 wt%. The results showed that: The 0.32 wt % CNT sample enhanced the interlaminar strength of the composite without enhancing the energy absorption capacity whereas, the 0.8 wt % CNT sample did not improve the impact resistance of the Kevlar composite.For the high speed impact tests, a bulletproof vest was prepared using woven Kevlar, resin, and CNTs at 1.5 w% percentage. The ballistic shooting was carried out by a professional shooter using a 30 caliber and 9 mm bullets for the tests. The CNT bulletproof sample bounced back the 30 caliber copper alloy bullet with no penetration.

Impact Behaviour of Composite Materials by Using Low and High Speed Impact Tests

2012 ◽  
Vol 445 ◽  
pp. 189-194
Author(s):  
Enver Bulent Yalcin ◽  
Volkan Gunay ◽  
Muzeyyen Marsoglu
Keyword(s):  
Composite Materials ◽  
High Speed ◽  
Impact Test ◽  
Woven Fabrics ◽  
Impact Behaviour ◽  
High Speed Impact ◽  
Impact Tests ◽  
Data Acquisition Software ◽  
Damage Process ◽  
The Impact

The study presents the need for instrumented testing to optimizing materials against impact forces. The objective of the study is how the impact behaviour of composite materials is investigated by slow and high speed impact tests. Instron Dynatup 9250HV and Instron Dynatup 8150 Impact test machines (Fig.1.) are used which are located in TUBITAK-MRC, Materials Institute , Impact Test Laboratory". The damage process in composite materials under low and high velocity impact loading and the impact energy-displacement properties of the composite materials were investigated. Composite samples were produced by woven fabrics. The results are given as graphs and tables. The Impulse Data Acquisition software is used to send the data to computer.

Sign in / Sign up

Export Citation Format

Share Document