Six Degree-of-Freedom Broadband Ground-Motion Observations with Portable Sensors: Validation, Local Earthquakes, and Signal Processing

2020 ◽  
Vol 110 (3) ◽  
pp. 953-969 ◽  
Author(s):  
Shihao Yuan ◽  
Andreino Simonelli ◽  
Chin-Jen Lin ◽  
Felix Bernauer ◽  
Stefanie Donner ◽  
...  
Keyword(s):  
Ground Motion ◽  
Central Italy ◽  
Rigid Base ◽  
Small Scale ◽  
Volcano Seismology ◽  
Source Inversion ◽  
Motion Sensitivity ◽  
Rotation Sensor ◽  
Wide Range ◽  
Portable Sensors

ABSTRACT The additional observation of three components of rotational ground motions has benefits for tilt-seismometer coupling (e.g., ocean-bottom seismometry and volcano seismology), local site characterization, wavefield separation, source inversion, glacial and planetary seismology, as well as the monitoring of structural health. Field applications have been mostly hampered by the lack of portable sensors with appropriate broadband operation range and weak-motion sensitivity. Here, we present field observations of the first commercial portable broadband rotation sensor specifically designed for seismology. The sensor is a three-component fiber-optic gyro strictly sensitive to ground rotation only. The sensor field performance and records are validated by comparing it with both array-derived rotation measurements and a navigation-type gyro. We present observations of the 2018 Mw 5.4 Hualien earthquake and the 2016 central Italy earthquake sequence. Processing collocated rotation and classical translation records shows the potential in retrieving wave propagation direction and local structural velocity from point measurements comparable to small-scale arrays of seismic stations. We consider the availability of a portable, broadband, high sensitivity, and low self-noise rotation sensor to be a milestone in seismic instrumentation. Complete and accurate ground-motion observations (assuming a rigid base plate) are possible in the near, local, or regional field, opening up a wide range of seismological applications.

Multicycle Simulation of Strike-Slip Earthquake Rupture for Use in Near-Source Ground-Motion Simulations

2021 ◽  
Author(s):  
Percy Galvez ◽  
Anatoly Petukhin ◽  
Paul Somerville ◽  
Jean-Paul Ampuero ◽  
Ken Miyakoshi ◽  
...  
Keyword(s):  
Ground Motion ◽  
Stress Drop ◽  
Slip Rate ◽  
Rupture Process ◽  
Earthquake Rupture ◽  
Rupture Velocity ◽  
Source Inversion ◽  
Dynamic Rupture ◽  
Wide Range ◽  
Source Scaling

ABSTRACT Realistic dynamic rupture modeling validated by observed earthquakes is necessary for estimating parameters that are poorly resolved by seismic source inversion, such as stress drop, rupture velocity, and slip rate function. Source inversions using forward dynamic modeling are increasingly used to obtain earthquake rupture models. In this study, to generate a large number of physically self-consistent rupture models, rupture process of which is consistent with the spatiotemporal heterogeneity of stress produced by previous earthquakes on the same fault, we use multicycle simulations under the rate and state (RS) friction law. We adopt a one-way coupling from multicycle simulations to dynamic rupture simulations; the quasidynamic solver QDYN is used to nucleate the seismic events and the spectral element dynamic solver SPECFEM3D to resolve their rupture process. To simulate realistic seismicity, with a wide range of magnitudes and irregular recurrence, several realizations of 2D-correlated heterogeneous random distributions of characteristic weakening distance (Dc) in RS friction are tested. Other important parameters are the normal stress, which controls the stress drop and rupture velocity during an earthquake, and the maximum value of Dc, which controls rupture velocity but not stress drop. We perform a parametric study on a vertical planar fault and generate a set of a hundred spontaneous rupture models in a wide magnitude range (Mw 5.5–7.4). We validate the rupture models by comparison of source scaling, ground motion (GM), and surface slip properties to observations. We compare the source-scaling relations between rupture area, average slip, and seismic moment of the modeled events with empirical ones derived from source inversions. Near-fault GMs are computed from the source models. Their peak ground velocities and peak ground accelerations agree well with the ground-motion prediction equation values. We also obtain good agreement of the surface fault displacements with observed values.

Dynamic Rupture and Ground Motion Modeling of the 2016 M6.2 Amatrice and M6.5 Norcia, Central Italy, Earthquakes Constrained by Bayesian Dynamic Source Inversion

2020 ◽  
Author(s):  
Taufiq Taufiqurrahman ◽  
Alice-Agnes Gabriel ◽  
Frantisek Gallovic ◽  
Lubica Valentova
Keyword(s):  
Ground Motion ◽  
Dynamic Models ◽  
Central Italy ◽  
Foot Wall ◽  
Source Inversion ◽  
Dynamic Rupture ◽  
Highly Efficient ◽  
Starting Point ◽  
Dynamic Source ◽  
Strong Ground

<p>The complex evolution of earthquake rupture during the 2016 Central Italy sequence and the uniquely dense seismological observations provide an opportunity to better understand the processes controlling earthquake dynamics, strong ground motion, and earthquake interaction. </p><p>We here use fault initial stress and friction conditions constrained by a novel Bayesian dynamic source inversion as a starting point for high-resolution dynamic rupture scenarios. The best-fitting forward models are chosen out of ~10<sup>6</sup> highly efficient simulations restricted to a simple planar dipping fault. Such constrained, highly heterogeneous dynamic models fit strong motion data well. Utilizing the open-source SeisSol software (www.seissol.org), we then take into account non-planar (e.g., listric) fault geometries, inelastic off-fault damage rheology, free surface effects and topography which cannot be accounted for in the highly efficient dynamic source inversion. SeisSol is based on the discontinuous Galerkin method on unstructured tetrahedral meshes optimized for modern supercomputers. </p><p>We investigate the effects of including the realistic modeling ingredients on rupture dynamics and strong ground motions up to 5 Hz. Synthetic PGV mapping reveals that specifically fault listricity decreases ground motion amplitudes by  ~50 percent in the extreme near field on the foot-wall. On the hanging-wall shaking is increased by ~150 percent as a consequence of wave-focusing effects within 10 km away from the fault. Dynamic modeling thus suggests that geometrical fault complexity is important for seismic hazard assessment adjacent to dipping faults but difficult to identify by kinematic source inversions.</p>

Integrated Design and Multi-Objective Optimization of a Single Stage Heat-Pump Turbocompressor

2013 ◽  
Author(s):  
J. Schiffmann
Keyword(s):  
Design Optimization ◽  
High Efficiency ◽  
Integrated Design ◽  
Heat Pumps ◽  
Small Scale ◽  
Multi Objective Optimization ◽  
Design Constraints ◽  
Multi Objective ◽  
Wide Range ◽  
Standard Design

Small scale turbomachines in domestic heat pumps reach high efficiency and provide oil-free solutions which improve heat-exchanger performance and offer major advantages in the design of advanced thermodynamic cycles. An appropriate turbocompressor for domestic air based heat pumps requires the ability to operate on a wide range of inlet pressure, pressure ratios and mass flows, confronting the designer with the necessity to compromise between range and efficiency. Further the design of small-scale direct driven turbomachines is a complex and interdisciplinary task. Textbook design procedures propose to split such systems into subcomponents and to design and optimize each element individually. This common procedure, however, tends to neglect the interactions between the different components leading to suboptimal solutions. The authors propose an approach based on the integrated philosophy for designing and optimizing gas bearing supported, direct driven turbocompressors for applications with challenging requirements with regards to operation range and efficiency. Using previously validated reduced order models for the different components an integrated model of the compressor is implemented and the optimum system found via multi-objective optimization. It is shown that compared to standard design procedure the integrated approach yields an increase of the seasonal compressor efficiency of more than 12 points. Further a design optimization based sensitivity analysis allows to investigate the influence of design constraints determined prior to optimization such as impeller surface roughness, rotor material and impeller force. A relaxation of these constrains yields additional room for improvement. Reduced impeller force improves efficiency due to a smaller thrust bearing mainly, whereas a lighter rotor material improves rotordynamic performance. A hydraulically smoother impeller surface improves the overall efficiency considerably by reducing aerodynamic losses. A combination of the relaxation of the 3 design constraints yields an additional improvement of 6 points compared to the original optimization process. The integrated design and optimization procedure implemented in the case of a complex design problem thus clearly shows its advantages compared to traditional design methods by allowing a truly exhaustive search for optimum solutions throughout the complete design space. It can be used for both design optimization and for design analysis.

scholarly journals Transport Cost Estimation Model of the Agroforestry Biomass in a Small-Scale Energy Chain

2020 ◽  
Vol 3 (1) ◽  
pp. 22
Author(s):  
Giulio Sperandio ◽  
Andrea Acampora ◽  
Vincenzo Civitarese ◽  
Sofia Bajocco ◽  
Marco Bascietto
Keyword(s):  
Supply Chain ◽  
Power Plant ◽  
Central Italy ◽  
Biomass Energy ◽  
Transport Cost ◽  
Small Scale ◽  
Economic Sustainability ◽  
Transport Costs ◽  
Energy Chain ◽  
Biomass Power Plant

The delivery of biomass products from the production place to the point of final use is of fundamental importance within the constitution of energy chains based on biomass use as renewable energy source. In fact, transport can be one of the most economically expensive operations of the entire biomass energy production process. In this work, a geographic identification, through remote sensing and photo-interpretation, of the different biomass sources was used to estimate the potential available biomass for energy in a small-scale supply chain. The economic sustainability of transport costs was calculated for different types of biomass sources available close to a biomass power plant of a small-scale energy supply chain, in central Italy. The proposed analysis allows us to highlight and visualize on the map the areas of the territory characterized by greater economic sustainability in terms of lower transport costs of residual agroforestry biomass from the collection point to the final point identified with the biomass power plant. The higher transport cost was around € 40 Mg−1, compared to the lowest of € 12 Mg−1.

scholarly journals A broadbanded pressure differential wave energy converter based on dielectric elastomer generators

2021 ◽  
Author(s):  
Michele Righi ◽  
Giacomo Moretti ◽  
David Forehand ◽  
Lorenzo Agostini ◽  
Rocco Vertechy ◽  
...  
Keyword(s):  
Wave Energy ◽  
Large Deformations ◽  
Dielectric Elastomer ◽  
Wave Energy Converter ◽  
Pressure Differential ◽  
Design Stage ◽  
Small Scale ◽  
Energy Converter ◽  
Wide Range ◽  
The Waves

AbstractDielectric elastomer generators (DEGs) are a promising option for the implementation of affordable and reliable sea wave energy converters (WECs), as they show considerable promise in replacing expensive and inefficient power take-off systems with cheap direct-drive generators. This paper introduces a concept of a pressure differential wave energy converter, equipped with a DEG power take-off operating in direct contact with sea water. The device consists of a closed submerged air chamber, with a fluid-directing duct and a deformable DEG power take-off mounted on its top surface. The DEG is cyclically deformed by wave-induced pressure, thus acting both as the power take-off and as a deformable interface with the waves. This layout allows the partial balancing of the stiffness due to the DEG’s elasticity with the negative hydrostatic stiffness contribution associated with the displacement of the water column on top of the DEG. This feature makes it possible to design devices in which the DEG exhibits large deformations over a wide range of excitation frequencies, potentially achieving large power capture in a wide range of sea states. We propose a modelling approach for the system that relies on potential-flow theory and electroelasticity theory. This model makes it possible to predict the system dynamic response in different operational conditions and it is computationally efficient to perform iterative and repeated simulations, which are required at the design stage of a new WEC. We performed tests on a small-scale prototype in a wave tank with the aim of investigating the fluid–structure interaction between the DEG membrane and the waves in dynamical conditions and validating the numerical model. The experimental results proved that the device exhibits large deformations of the DEG power take-off over a broad range of monochromatic and panchromatic sea states. The proposed model demonstrates good agreement with the experimental data, hence proving its suitability and effectiveness as a design and prediction tool.

scholarly journals A Threat of Farmers’ Suicide and the Opportunity in Organic Farming for Sustainable Agricultural Development in India

2019 ◽  
Vol 11 (8) ◽  
pp. 2400 ◽  
Author(s):  
Karthikeyan Mariappan ◽  
Deyi Zhou
Keyword(s):  
Organic Farming ◽  
Tamil Nadu ◽  
Agricultural Development ◽  
Small Scale ◽  
Conventional Farming ◽  
Wide Range ◽  
Significant Difference ◽  
Small Scale Farmers ◽  
The Cost ◽  
Input Cost

Agriculture is the main sources of income for humans. Likewise, agriculture is the backbone of the Indian economy. In India, Tamil Nadu regional state has a wide range of possibilities to produce all varieties of organic products due to its diverse agro-climatic condition. This research aimed to identify the economics and efficiency of organic farming, and the possibilities to reduce farmers’ suicides in the Tamil Nadu region through the organic agriculture concept. The emphasis was on farmers, producers, researchers, and marketers entering the sustainable economy through organic farming by reducing input cost and high profit in cultivation. A survey was conducted to gather data. One way analysis of variance (ANOVA) has been used to test the hypothesis regards the cost and profit of rice production. The results showed that there was a significant difference in profitability between organic and conventional farming methods. It is very transparent that organic farming is the leading concept of sustainable agricultural development with better organic manures that can improve soil fertility, better yield, less input cost and better return than conventional farming. The study suggests that by reducing the cost of cultivation and get a marginal return through organic farming method to poor and small scale farmers will reduce socio-economic problems such as farmers’ suicides in the future of Indian agriculture.

Electromechanical fields in a hollow piezoelectric cylinder under non-uniform load: flexoelectric effect

2021 ◽  
pp. 108128652110207
Author(s):  
Olha Hrytsyna
Keyword(s):  
Analytical Solutions ◽  
Point Group ◽  
The Body ◽  
Small Scale ◽  
Gradient Theory ◽  
Local Mass ◽  
Wide Range ◽  
Mass Displacement ◽  
Local Mass Displacement ◽  
Local Gradient

The relations of a local gradient non-ferromagnetic electroelastic continuum are used to solve the problem of an axisymmetrical loaded hollow cylinder. Analytical solutions are obtained for tetragonal piezoelectric materials of point group 4 mm for two cases of external loads applied to the body surfaces. Namely, the hollow pressurized cylinder and a cylinder subjected to an electrical voltage V across its thickness are considered. The derived solutions demonstrate that the non-uniform electric load causes a mechanical deformation of piezoelectric body, and vice versa, the inhomogeneous radial pressure of the cylinder induces its polarization. Such a result is obtained due to coupling between the electromechanical fields and a local mass displacement being considered. In the local gradient theory, the local mass displacement is associated with the changes to a material’s microstructure. The classical theory does not consider the effect of material microstructure on the behavior of solid bodies and is incapable of explaining the mentioned phenomena. It is also shown that the local gradient theory describes the size-dependent properties of piezoelectric nanocylinders. Analytical solutions to the formulated boundary-value problems can be used in conjunction with experimental data to estimate some higher-order material constants of the local gradient piezoelectricity. The obtained results may be useful for a wide range of appliances that utilize small-scale piezoelectric elements as constituting blocks.

scholarly journals A Comparison of Some Methods of Deriving the Instantaneous Unit Hydrograph

1985 ◽  
Vol 16 (1) ◽  
pp. 1-10 ◽  
Author(s):  
V. P. Singh ◽  
C. Corradini ◽  
F. Melone
Keyword(s):  
Peak Flow ◽  
Central Italy ◽  
Effective Rainfall ◽  
Unit Hydrograph ◽  
Time To Peak ◽  
Wide Range ◽  
Instantaneous Unit Hydrograph ◽  
Similar Accuracy ◽  
Two Parameters ◽  
Range Of Values

The geomorphological instantaneous unit hydrograph (IUH) proposed by Gupta et al. (1980) was compared with the IUH derived by commonly used time-area and Nash methods. This comparison was performed by analyzing the effective rainfall-direct runoff relationship for four large basins in Central Italy ranging in area from 934 to 4,147 km2. The Nash method was found to be the most accurate of the three methods. The geomorphological method, with only one parameter estimated in advance from the observed data, was found to be little less accurate than the Nash method which has two parameters determined from observations. Furthermore, if the geomorphological and Nash methods employed the same information represented by basin lag, then they produced similar accuracy provided the other Nash parameter, expressed by the product of peak flow and time to peak, was empirically assessed within a wide range of values. It was concluded that it was more appropriate to use the geomorphological method for ungaged basins and the Nash method for gaged basins.

Observations of Small-Scale Turbulence and Energy Dissipation Rates in the Cloudy Boundary Layer

2006 ◽  
Vol 63 (5) ◽  
pp. 1451-1466 ◽  
Author(s):  
Holger Siebert ◽  
Katrin Lehmann ◽  
Manfred Wendisch
Keyword(s):  
Boundary Layer ◽  
Energy Dissipation ◽  
Wind Velocity ◽  
Turbulence Theory ◽  
Horizontal Wind ◽  
Inertial Subrange ◽  
Intermittent Flow ◽  
Small Scale ◽  
Dissipation Rates ◽  
Wide Range

Abstract Tethered balloon–borne measurements with a resolution in the order of 10 cm in a cloudy boundary layer are presented. Two examples sampled under different conditions concerning the clouds' stage of life are discussed. The hypothesis tested here is that basic ideas of classical turbulence theory in boundary layer clouds are valid even to the decimeter scale. Power spectral densities S( f ) of air temperature, liquid water content, and wind velocity components show an inertial subrange behavior down to ≈20 cm. The mean energy dissipation rates are ∼10−3 m2 s−3 for both datasets. Estimated Taylor Reynolds numbers (Reλ) are ∼104, which indicates the turbulence is fully developed. The ratios between longitudinal and transversal S( f ) converge to a value close to 4/3, which is predicted by classical turbulence theory for local isotropic conditions. Probability density functions (PDFs) of wind velocity increments Δu are derived. The PDFs show significant deviations from a Gaussian distribution with longer tails typical for an intermittent flow. Local energy dissipation rates ɛτ are derived from subsequences with a duration of τ = 1 s. With a mean horizontal wind velocity of 8 m s−1, τ corresponds to a spatial scale of 8 m. The PDFs of ɛτ can be well approximated with a lognormal distribution that agrees with classical theory. Maximum values of ɛτ ≈ 10−1 m2 s−3 are found in the analyzed clouds. The consequences of this wide range of ɛτ values for particle–turbulence interaction are discussed.

scholarly journals Surface kinetic energy transfer in surface quasi-geostrophic flows

2008 ◽  
Vol 604 ◽  
pp. 165-174 ◽  
Author(s):  
XAVIER CAPET ◽  
PATRICE KLEIN ◽  
BACH LIEN HUA ◽  
GUILLAUME LAPEYRE ◽  
JAMES C. MCWILLIAMS
Keyword(s):  
Kinetic Energy ◽  
Surface Velocity ◽  
Small Scale ◽  
Surface Dynamics ◽  
Spectral Flux ◽  
Advection Term ◽  
Wide Range ◽  
Geostrophic Flows ◽  
Scale Range ◽  
Density Variance

The relevance of surface quasi-geostrophic dynamics (SQG) to the upper ocean and the atmospheric tropopause has been recently demonstrated in a wide range of conditions. Within this context, the properties of SQG in terms of kinetic energy (KE) transfers at the surface are revisited and further explored. Two well-known and important properties of SQG characterize the surface dynamics: (i) the identity between surface velocity and density spectra (when appropriately scaled) and (ii) the existence of a forward cascade for surface density variance. Here we show numerically and analytically that (i) and (ii) do not imply a forward cascade of surface KE (through the advection term in the KE budget). On the contrary, advection by the geostrophic flow primarily induces an inverse cascade of surface KE on a large range of scales. This spectral flux is locally compensated by a KE source that is related to surface frontogenesis. The subsequent spectral budget resembles those exhibited by more complex systems (primitive equations or Boussinesq models) and observations, which strengthens the relevance of SQG for the description of ocean/atmosphere dynamics near vertical boundaries. The main weakness of SQG however is in the small-scale range (scales smaller than 20–30 km in the ocean) where it poorly represents the forward KE cascade observed in non-QG numerical simulations.

Sign in / Sign up

Export Citation Format

Share Document