scholarly journals Effect of Chemical and Mechanical Degradation on Surface Roughness, Topography, Gloss, and Polish Retention of Three Composites Polished with Five Polishing Systems

2021 ◽  
Author(s):  
Fatemeh Farzaneh ◽  
Mahshid Mohammadi-Bassir ◽  
Mohammad Bagher Rezvani ◽  
Fahimeh Dehestani Ardakani
Keyword(s):  
Surface Roughness ◽  
Composite Resins ◽  
Mechanical Degradation ◽  
P System ◽  
Mean Values ◽  
Before And After ◽  
Ph Cycling ◽  
The Mean ◽  
Level Of Significance ◽  
Surface Gloss

Objective: Finishing and polishing (F/P) of composites is a fundamental step influencing the clinical service of restorations. The aim of this study was to evaluate the effect of different F/P systems on surface roughness, gloss, and polish retention of composite resins. Materials and Methods: One-hundred and five disc-shaped specimens (4×4 mm) were made from nanofilled, microhybrid, and microfilled composites (n=35). The specimens were divided into five subgroups (n=7) for F/P with Sof-Lex (4-step), Shofu (4-step), Cosmedent (3-step), Diacomp Composite-Pro (2-step), and Opti1Step systems. The surface roughness values (Ra and Rz) were measured before and after pH-cycling and simulated toothbrushing. Surface topography was assessed by using a scanning electron microscope (SEM) at three magnifications. For assessment of surface gloss, 45 rectangular specimens (10×8×2 mm) were fabricated from three composites (n=15) and randomly allocated to five subgroups (n=3). Surface gloss was measured before and after aging. The mean values were calculated and analyzed by two-way ANOVA, Tukey, and t-test. Level of significance was set at 0.05.  Results:  The composite type had no significant effect on surface roughness (P>0.05); however, the type of F/P system significantly affected it (P<0.05). The pH-cycling and simulated toothbrushing had no significant effect on gloss or polish retention of the three composites (P>0.05). Conclusion: Type of F/P system had a greater effect on surface roughness and gloss of composite resins than the type of composite.

scholarly journals A novel prediction of simulated fluid responsiveness by echocardiography assessment of tricuspid annulus tissue velocity with passive leg raising

2019 ◽  
Vol 27 (5) ◽  
pp. 270-276
Author(s):  
Erden Erol Ünlüer ◽  
Arif Karagöz ◽  
Serdar Bayata ◽  
Sibel Çatalkaya ◽  
Hüseyin Bozdemir
Keyword(s):  
Cardiac Output ◽  
Fluid Responsiveness ◽  
Vital Signs ◽  
Peak Systolic Velocity ◽  
Passive Leg Raising ◽  
Tricuspid Annulus ◽  
Mean Values ◽  
Before And After ◽  
The Mean ◽  
Level Of Significance

Background: Fluid responsiveness can be predicted by the effect of passive leg raising on cardiac output. Objectives: This research aimed to compare the changes in cardiac output and the peak systolic velocity values of Tricuspid annulus velocity at the free wall (S’) before and after passive leg raising in healthy volunteers. Methods: The study was approved by ethical commission. The desired sample size was 28, and 57 volunteers were included after they signed informed consent. The first measurements, including vital signs, S’, and cardiac output, were taken with the participants lying supine and were performed in the morning after 12 h fast. The participants were then asked to lie in a semirecumbent position for 3 min. After 3 min, the head of the bed was lowered to the supine position and the participants’ legs were elevated at 45°. Secondary measurements were repeated in this position. The differences between vital signs, cardiac output, and S’ measurements before and after passive leg raising were statistically compared. The level of significance was set as p < 0.05. Results: The mean values of cardiac output and S’ before passive leg raising was 9.59 L/min and 11.57 cm/s, respectively; however, those increased to 11.44 L/min and 13.72 cm/s after passive leg raising. The average increases were 16.17% for cardiac output and 15.67% for S’. The changes of cardiac output and S’ were statistically significant. The changes of vital signs before and after passive leg raising were statistically insignificant. Conclusion: This study has demonstrated the concordance of rise in cardiac output with S’ change by passive leg raising in healthy subjects. Further studies are needed to validate the use of S’ values in critically ill subjects.

scholarly journals Effect of Energy Drinks on the Surface Texture of Nanofilled Composite Resin

2013 ◽  
Vol 14 (5) ◽  
pp. 830-835 ◽  
Author(s):  
Khalid H Al-Samadani
Keyword(s):  
Surface Roughness ◽  
Aging Time ◽  
Surface Texture ◽  
Composite Resin ◽  
Energy Drinks ◽  
Composite Resins ◽  
Mean Values ◽  
Before And After ◽  
Bonferroni Test ◽  
Red Bull

ABSTRACT Objective To study the effect of three energy drinks on the surface roughness of nanofilled composite resins after different periods of aging time. Materials and methods Composite resin disks, 6 mm diameter, 3 mm thickness were prepared from Filtec Z350 XT, Tetric EvoCeram and Filtec Z250 XT. Specimens fr/8om each material were tested after aging with Red Bull, Bison and Power Horse energy drinks and distilled water as a control. Specimens were stored at 37°C in dark containers for 1, 3 and 6 months. Surface roughness Ra was assessed using a surface scanning interferometry before and after each storage period. Surface roughness differences ΔRa and Ra among specimens were measured. Mean values were statistically analyzed using multiple repeated measured (ANOVA), variance and multiple comparisons of the mean values were done with Bonferroni test, with p < 0.05 as significance level. Results The surface roughness degradation change ?Ra and Ra value before and after occurred by Red Bull, Bison and Power Horse energy drinks was significantly different for all tested materials at all three times p < 0.05. All specimens showed increase in surface roughness changes after aging periods of 1, 3 and 6 months. The highest total surface roughness difference ΔRa and Ra was found in the Red Bull group after 6 months. Conclusion Energy drinks used in this study had surface degradation effect on the tested composite resin materials. The surface roughness increased with aging time however, it was clinically acceptable in all test groups after 6 months. The effect of energy drinks solutions on the surface roughness parameter of resin composites depends on type of solution and its acidity contents. How to cite this article Al-Samadani KH. Effect of Energy Drinks on the Surface Texture of Nanofilled Composite Resin. J Contemp Dent Pract 2013;14(5):830-835.

scholarly journals Surface roughness of indirect composites using different polishing systems

2013 ◽  
Vol 16 (4) ◽  
pp. 77 ◽  
Author(s):  
Daphne Camara Barcellos ◽  
Alexandre Luiz Souto Borges ◽  
Alessandra Buhler Borges ◽  
Patricia Rondon Pleffken ◽  
Sigmar Mello Rode
Keyword(s):  
Surface Roughness ◽  
Standard Deviation ◽  
Aluminum Oxide ◽  
Composite Resins ◽  
Mean Values ◽  
Indirect Composites ◽  
Dental Polishing ◽  
The Mean

<p><strong>Objective: </strong>The aim of this study was to evaluatethe surface roughness of indirect composites afterpolishing with aluminum oxide (Al2O3) discs. <strong>Materialand Methods</strong>: One-hundred and eighty specimenswere confectioned with 6 indirect composites using aprefabricated matrix, resulting in six groups (n-30):Group SO - Solidex, Group SI - Signum, Group SF- Sinfony, Group OP - Opallis; Group RE - Resilab,Group EP - Epricord, Group AD - Adoro. Each groupwas divided into three subgroups according to thepolishing (n-10): Subgroup C (Control) - withoutpolishing (polyester strip); Subgroup S - polishingwith Sof-Lex discs; Subgroup T - polishing with TDVdiscs. The surface roughness was measured with aprofilometer. <strong>Results: </strong>The results were analyzed byANOVA and Tukey tests (5%), resulting in p = 0.00.The mean values (±standard-deviation) measured inRa (μm) for each Group/Subgroup were: RE/C - 0.14(± 0.14) a; EP/C - 0.18 (± 0.46) ab; SO/C - 0.24 (±0.22) abc; SF/S - 0.24 (± 0.17) abc; SF/C - 0.26 (±2.54)abc; SI/C - 0.30 (± 0.34)abcd; SO/T - 0.33(±0.42) abcd; AD/S - 0.34(± 0.88)abcd; AD/C - 0.37(±0.60)ab; SI/S - 0.37(± 1.39)bcd; SO/S - 0.43(± 0.26)cd; EP/S – 0.44 (± 1.02) cd; RE/S - 0.54(±2.02) de;SI/T - 0.65(± 0.88)ef; RE/T - 0.83 (± 0.54) fg; SF/T- 0.85 (± 0.21) fg; AD/T - 0.88 (± 1.74) fg; EP/T- 0.91(± 0.89) g. <strong>Conclusion: </strong>It is concluded thatpolyester strip resulted in significantly lowest surfaceroughness; polishing with TDV discs resulted insignificantly higher surface roughness compared toSof-Lex discs and that the surface roughness resultsdepend on the composite tested.</p><p>Keywords<br />Composite resins; Dental polishing; Biofilms.</p>

scholarly journals Influence of Apical Patency and Cleaning of the Apical Foramen on Periapical Extrusion in Retreatment

2013 ◽  
Vol 24 (5) ◽  
pp. 482-486 ◽  
Author(s):  
Marili Doro Andrade Deonizio ◽  
Gilson Blitzkow Sydney ◽  
Antonio Batista ◽  
Roberto Pontarolo ◽  
Paulo Ricardo Bittencourt Guimarães ◽  
...  
Keyword(s):  
Material Removal ◽  
Filling Material ◽  
Mean Values ◽  
Filtration System ◽  
Root Canal Retreatment ◽  
Significant Difference ◽  
Before And After ◽  
The Mean ◽  
The Difference ◽  
Removal Technique

This study evaluated the influence of apical patency, root filling removal technique and cleaning of the apical foramen, concerning the amount of debris extruded during root canal retreatment. Forty mandibular incisors were randomly assigned to 4 groups - GIM (n=10), GIIM (n=10), GIPT (n=10) and GIIPT (n=10), which were named according to leaving (I) or not (II) apical patency during canal preparation and filling removal technique (manual - M or ProTaper system - PT). After filling material removal, each specimen of each group had the apical foramen cleaned by sizes 15, 20 and 25 instruments, generating 12 subgroups: GIM15, GIM20, GIM25, GIIM15, GIIM20, GIIM25, GIPT15, GIPT20, GIPT25, GIIPT15, GIIPT20 and GIIPT25. Extruded filling debris was collected by a Milipore filtration system, an HV-durapore, 0.45 µm pore filter with a 25 mm diameter. The filters were weighed before and after the collection on an analytical scale (10–5 g), and the difference was calculated. The mean weight of extruded filling debris was analyzed statistically by Kruskal-Wallis and Friedman ANOVA tests (α=0.05). The mean values found in the groups (in mg) were: GIM (0.95±0.94), GIIM (0.47±0.62), GIPT (0.30±0.31) and GIIPT (0.32±0.44). There was no statistically significant difference among any of the groups or subgroups (p>0.05). ProTaper provided the smallest amount of extruded filling material, regardless of presence or absence of apical patency, followed by manual technique, without and with apical patency. Additional amounts of debris were collected during cleaning of the apical foramen, regardless of the instrument, presence/absence of patency or root filling removal technique.

scholarly journals Accelerated Aging Effects on Surface Hardness and Roughness of Lingual Retainer Adhesives

2008 ◽  
Vol 78 (1) ◽  
pp. 140-144 ◽  
Author(s):  
Sabri Ilhan Ramoglu ◽  
Serdar Usumez ◽  
Tamer Buyukyilmaz
Keyword(s):  
Surface Roughness ◽  
Vickers Hardness ◽  
Statistical Significance ◽  
Accelerated Aging ◽  
Aging Effects ◽  
Surface Microhardness ◽  
Halogen Light ◽  
Before And After ◽  
The Mean ◽  
Lingual Retainer

Abstract Objective: To test the null hypothesis that accelerated aging has no effect on the surface microhardness and roughness of two light-cured lingual retainer adhesives. Materials and Methods: Ten samples of light-cured materials, Transbond Lingual Retainer (3M Unitek) and Light Cure Retainer (Reliance) were cured with a halogen light for 40 seconds. Vickers hardness and surface roughness were measured before and after accelerated aging of 300 hours in a weathering tester. Differences between mean values were analyzed for statistical significance using a t-test. The level of statistical significance was set at P &lt; .05. Results: The mean Vickers hardness of Transbond Lingual Retainer was 62.8 ± 3.5 and 79.6 ± 4.9 before and after aging, respectively. The mean Vickers hardness of Light Cure Retainer was 40.3 ± 2.6 and 58.3 ± 4.3 before and after aging, respectively. Differences in both groups were statistically significant (P &lt; .001). Following aging, mean surface roughness was changed from 0.039 μm to 0.121 μm and from 0.021 μm to 0.031 μm for Transbond Lingual Retainer and Light Cure Retainer, respectively. The roughening of Transbond Lingual Retainer with aging was statistically significant (P &lt; .05), while the change in the surface roughness of Light Cure Retainer was not (P &gt; .05). Conclusions: Accelerated aging significantly increased the surface microhardness of both light-cured retainer adhesives tested. It also significantly increased the surface roughness of the Transbond Lingual Retainer.

Postural habits in adolescents: the influence of a school physiotherapy program on improving the knowledge of postures

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Beatriz Minghelli
Keyword(s):  
Health Literacy ◽  
Mobile Phones ◽  
Intervention Program ◽  
Measurement Instruments ◽  
Mean Values ◽  
Practical Test ◽  
Heavy Object ◽  
Physiotherapy Program ◽  
Before And After ◽  
The Mean

AbstractBackgroundSchool physiotherapy programs can promote an increase in health literacy promoting healthier postural habits. This study aimed to verify the effectiveness of this program in improving the theoretical-practical ergonomic knowledge about postures in adolescents and to verify the postural habits adopted.MethodsThe sample comprised 206 students, 109 (52.9%) being boys, aged 12–19 years old. The measurement instruments included a theoretical-practical test and a scale. The intervention program included one session lasting 90 min, using both theoretical and practical approaches.ResultsThe mean values obtained on the theoretical-practical test before and after the 1-month period were 9.14 ± 2.51 and 13.05 ± 1.41, respectively (p ≤ 0.001). One hundred and ninety-nine (96.6%) students sat with the spine wrongly positioned, 197 (95.6%) students used mobile phones with a cervical flexion, and 165 (80.1%) lifted a heavy object from the floor incorrectly.ConclusionsThis data revealed that a school physiotherapy program improves ergonomic knowledge in adolescents.

scholarly journals Effect of whitening dentifrices on the surface roughness of a nanohybrid composite resin

2016 ◽  
Vol 10 (02) ◽  
pp. 170-175 ◽  
Author(s):  
Gabriela Migliorin da Rosa ◽  
Luciana Mendonça da Silva ◽  
Márcio de Menezes ◽  
Hugo Felipe do Vale ◽  
Diego Ferreira Regalado ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Composite Resin ◽  
Wilcoxon Test ◽  
Control Group ◽  
Mean Values ◽  
Short Period ◽  
Significant Difference ◽  
Before And After ◽  
Nanohybrid Composite ◽  
One Way Anova

ABSTRACT Objectives: The present study verified the influence of whitening dentifrices on the surface roughness of a nanohybrid composite resin. Materials and Methods: Thirty-two specimens were prepared with Filtek™ Z350 XT (3M/ESPE) and randomly divided into four groups (n = 08) that were subjected to brushing simulation equivalent to the period of 1 month. The groups assessed were a control group with distilled water (G1), Colgate Total 12 Professional Clean (G2), Sensodyne Extra Whitener Extra Fresh (G3), and Colgate Luminous White (G4). A sequence of 90 cycles was performed for all the samples. The initial roughness of each group was analyzed by the Surface Roughness Tester (TR 200-TIME Group Inc., CA, USA). After the brushing period, the final roughness was measured, and the results were statistically analyzed using nonparametric Kruskal–Wallis and Dunn tests for intergroup roughness comparison in the time factor. For intragroup and “Δ Final − Initial” comparisons, the Wilcoxon test and (one-way) ANOVA were, respectively, performed (α = 0.05). Results: The roughness mean values before and after brushing showed no statistically significant difference when the different dentifrices were used. None of the dentifrices analyzed increased significantly the nanohybrid composite resin surface roughness in a 1 month of tooth brushing simulation. Conclusions: These results suggest that no hazardous effect on the roughness of nanohybrid composite resin can be expected when whitening dentifrices are used for a short period. Similar studies should be conducted to analyze other esthetic composite materials.

scholarly journals Color Stability and Surface Roughness of Hybrid and Nanofilled Composites Brushed with Abrasive Dentifrices

2021 ◽  
Vol 23 (2) ◽  
pp. 85-91
Author(s):  
Guilherme Ortiz Pinto Cruz ◽  
Larissa Martins Costa ◽  
Cesar Penazzo Lepri ◽  
Ruchele Dias Nogueira ◽  
Regina Guenka Palma-Dibb ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Laser Scanning ◽  
Color Change ◽  
Color Stability ◽  
Composite Resins ◽  
Laser Scanning Microscopy ◽  
Confocal Laser ◽  
Test Surface ◽  
Initial Color ◽  
Level Of Significance

AbstractThe aim of this study was to evaluate the color stability and the surface roughness of different composites brushed with toothpastes presenting different levels of abrasivity. Thirty discs of each material were obtained using michohybrid composites (Brilliant NG and Charisma Diamond) and a nanocomposite (Filtek Z350XT). The initial color (CIELab) and surface roughness (confocal laser scanning microscopy) of resin discs were evaluated. Afterwards, 10 specimens per group were brushed with the following dentifrices: Maximum Cavity Protection, Sensodyne Repair & Protect and Colgate Sensitive Pro-Relief. Brushing was performed with an electric toothbrush equipped with soft bristle head, with standard power and weight, for 30 minutes. Every 30 seconds, 1.0 ml of the slurry was injected between the bristles of the brush and the specimen. After abrasive challenge, the samples had their color and roughness reevaluated. Data were submitted to the Kruskal-Wallis test (color change) or the t-test (surface roughness). The level of significance was 5%. Results: Brushing did not significantly change the color of the composites tested in the study herein . On the other hand, the surface roughness of the composites was significantly affected by the abrasive challenge, regardless of the toothpaste used. The surface roughness change was similar for all the composites. The abrasive challenge with the toothpastes Maximum Cavity protection, Sensodyne Repair & Protect and Colgate Sensitive Pro-Relief was not able to significantly change the color of the composite resins. Nevertheless, the abrasive challenges significantly altered the surface roughness of all the evaluated composites. However, the changes in surface roughness were statistically similar in the microhybrid and nanofilled composites. Keywords: Composites Resins. Dentifrices. Color. ResumoO objetivo deste estudo foi avaliar a estabilidade de cor e a rugosidade superficial de diferentes resinas compostas escovadas com dentifrícios de diferentes níveis de abrasividade. Trinta discos de cada material foram obtidos utilizando compósitos micro-híbridos (Brilliant NG e Charisma Diamond) e um nanocompósito (Filtek Z350XT). A cor inicial (CIELab) e a rugosidade superficial (microscopia confocal de varredura a laser) dos discos de resina foram avaliadas. Em seguida, 10 amostras por grupo foram escovadas com os dentifrícios Máxima Proteção Anticáries, Sensodyne Repair & Protect e Colgate Sensitive Pro-Alívio. A escovação foi realizada com uma escova elétrica com cabeça de cerdas macias, com potência e peso padronizados, durante 30 minutos. A cada 30 segundos, 1,0 ml da pasta era injetada entre as cerdas da escova e a amostra. Após o desafio abrasivo, as amostras tiveram sua cor e rugosidade reavaliadas. Os dados foram submetidos ao teste de Kruskal-Wallis (alteração de cor) ou ao teste t (rugosidade da superfície) (α=5%). A escovação não alterou significativamente a cor dos compósitos. Por outro lado, a rugosidade superficial dos compósitos foi significativamente afetada pelo desafio abrasivo, independentemente do dentifrício utilizado. A alteração da rugosidade superficial foi semelhante para todos os compósitos. O desafio abrasivo com a Máxima Proteção Anticáries, o Sensodyne Repair & Protect e o Colgate Sensitive Pro-Alívio não foi capaz de alterar significativamente a cor das resinas. Diferentemente, os desafios abrasivos alteraram significativamente a rugosidade superficial de todos os compósitos avaliados. No entanto, as mudanças na rugosidade foram estatisticamente semelhantes nos compósitos micro-híbridos e nanoparticulado. Palavras-chave: Resinas Compostas. Dentifrícios. Cor.

scholarly journals Influence of Silver Nanoparticles on the Specific Properties of Acrylic Resin for Ocular Prosthesis

2018 ◽  
Vol 11 (3) ◽  
pp. 1573-1581 ◽  
Author(s):  
Maha M. Turki ◽  
Faiza M. Abdul-Ameer
Keyword(s):  
Surface Roughness ◽  
Impact Strength ◽  
Flexural Strength ◽  
Bond Strength ◽  
Shear Bond Strength ◽  
Acrylic Resin ◽  
Control Group ◽  
Mean Values ◽  
The Mean ◽  
Group B

Scleral acrylic resin is widely used to synthesize ocular prosthesis. However, the properties of this material change over time, thus requiring the prosthesis to be refabricated. Many studies were conducted to improve these properties by reinforcing this material with nanoparticles. This study aims to evaluate the effect of silver nanoparticle powder on the mechanical properties (transverse flexural strength, impact strength, shear bond strength, surface microhardness, and surface roughness) of scleral acrylic resin used for ocular prostheses. Two concentrations were selected from the pilot study and evaluated for their effects on scleral acrylic resin properties. According to the pilot study, 0.01 and 0.02wt% AgNPs powder improved the transverse flexural strength, microhardness, and surface roughness compared with other percentages. The specimens in the main study were divided into (3) main groups, (50) specimens without additives (control group A), (50) experimental specimens (with 0.01wt% AgNPs group B), and (50) experimental specimens (with 0.02 wt% AgNPs group C). Each group was subdivided into (5) equal subgroups depending on the tests used. The data were studied using one way ANOVA and post hoc LSD test. At 0.01 wt% AgNPs addition, the mean values of transverse flexural strength insignificantly increased (p> 0.05), and those of impact strength and shear bond strength significantly increased (p< 0.05) compared with those of the control group. At 0.02 wt% AgNPs addition (group C), the mean value of transverse flexural strength significantly increased (p< 0.05), that of impact strength insignificantly increased (p> 0.05), and that of shear bond strength increased with high significance (p< 0.01) compared with those of the control group. Group C showed insignificant increase in the mean values of transverse flexural strength, impact strength, and shear bond strength (p. 0.05) compared with group B. The scleral acrylic resin added with 0.01 and 0.02 wt% AgNPs showed insignificant increase in microhardness and insignificant decrease in surface roughness. The addition of AgNPs powder in both concentrations improved the mechanical properties of scleral acrylic resin used for ocular prostheses.

scholarly journals Evaluation of the Results of Arthroscopic Release in Limits of Movement in Knees

2020 ◽  
Author(s):  
Mohammad Reza Sobhan ◽  
Seyed Hossein Saeed Banadaky ◽  
Mohammad Shafiee ◽  
Mohammad Gheisari
Keyword(s):  
Statistical Tests ◽  
Cross Sectional Study ◽  
Knee Score ◽  
Cross Sectional ◽  
Mean Values ◽  
Arthroscopic Release ◽  
Lysholm Knee Score ◽  
Significant Difference ◽  
Before And After ◽  
The Mean

Introduction: Limits of movement in knees is one of the most common complications following trauma and surgery. With early diagnosis and appropriate treatment choices, knee replacement and performance improvement are expected in many patients. However, limits of movement in knees is unpleasant and should be corrected as soon as possible. In this study, we decided to evaluate the results of arthroscopic release in motion limits of knees. Methods: This was a descriptive cross-sectional study.14 patients who referred to the Shahid Sadoughi Hospital of Yazd from 2014 to 2016 and diagnosed with knee limitation (flexion or extension restriction of more than 10 degrees) were selected. Patients were undergone arthroscopic release and followed-up for 6 months. Lysholm knee score, degrees of flexion and extension, and patient satisfaction were evaluated. The results were analyzed by SPSS-18 and statistical tests Paired T-test as well as Spearman correlation. Results: The mean age of the patients was 28.92±10.99 years. The most common type of trauma in the patients was femoral distal fracture (46.7%). The frequency of the patients' satisfaction with arthroscopy was as followed: 50% (7 patients), had moderate satisfaction, 28.6% (4 ones), high satisfaction, and 21.4% (3 ones) had low satisfaction.The mean difference in Lysholm Knee Score, improvement in degree of extension, improvement in degree of flexion and pain score before and after arthroscopy were 26.21±14.11,64.78±26.13,3.57±2.92 and 4.13±1.65,respectively.There was a significant difference between the mean values of these factors before and after arthroscopy. Conclusion: According to the results obtained, we can conclude that arthroscopic release is an effective and low-complication method in motion limits of knees.

Sign in / Sign up

Export Citation Format

Share Document