scholarly journals Model of a Photovoltaic Cell for the MatLab/Simulink SimPowerSystems Library

2019 ◽  
Vol 62 (2) ◽  
pp. 135-145 ◽  
Author(s):  
D. I. Zalizny
Keyword(s):  
Solar Irradiance ◽  
Power Plants ◽  
Cell Model ◽  
Photovoltaic Cell ◽  
Design Stage ◽  
Photovoltaic Module ◽  
Model Parameters ◽  
Matlab Simulink ◽  
Photovoltaic Modules ◽  
Simulink Model

A new Simulink model of a photovoltaic cell has been proposed. The model is focused on the use of a standard SimPowerSystems library with power engineering elements from the MatLab/Simulink software package. The model allows altering the values of solar irradiance, photovoltaic cell temperature and load resistance. The results of the model application are the calculated values of voltages and currents at the photovoltaic cell output. The Simulink model that has been developed implements the known dependence of the photovoltaic cell volt-ampere characteristic by using both standard MatLab/Simulink blocks and special electric SimPowerSystems library blocks. The model is characterized by the fact that the series and parallel resistance of the photovoltaic cell are made in the form of resistors from the SimPowerSystems library. The main calculation algorithm is implemented programmatically by using the “C” programming language. To increase the algorithm stability to algebraic cycles the restrictions parameters are introduced. A new technique of calculating the photovoltaic cell model parameters based on experimental data has been proposed. The technique includes the preparation of a system of equations with experimental values of the photovoltaic cell voltages and currents. Experimental tests have been carried out for the photovoltaic module OSP XTP 250 under different solar irradiance values. The tests showed that the relative error of the Simulink model that has been developed does not exceed 12 %. The Simulink model makes it possible to build photovoltaic modules and then to build schemes of photovoltaic power plants as a part of power supply systems. Due to the latter it is possible to simulate the electricity consumers’ work, weather conditions, and the presence of shadows or pollution on the surface of photovoltaic modules. Also, one can carry out a simulation of increasing failures in power plant photovoltaic modules, e.g. simulating of modules efficiency reducing because of their degradation, or simulating of modules series resistance increasing because of the photovoltaic cell internal contacts deterioration. The Simulink model that has been developed can be used both at the design stage and at the stage of photoelectric power plants operation.

scholarly journals Model of a Photovoltaic Module for the MatLab/Simulink SimPowerSystems Library

2020 ◽  
Vol 63 (6) ◽  
pp. 515-525
Author(s):  
D. I. Zalizny
Keyword(s):  
Power Plants ◽  
Experimental Studies ◽  
Solar Irradiation ◽  
Design Stage ◽  
Photovoltaic Module ◽  
Maximum Relative Error ◽  
Partial Shading ◽  
Matlab Simulink ◽  
Simulink Model ◽  
Photovoltaic Power

The relevance of research is caused by the increase of the number of photovoltaic power plants in the Republic of Belarus and, accordingly, the need to solve problems of diagnostics of photovoltaic modules. A new Simulink model of a photovoltaic module focused on using the standard SimPowerSystems library of power supply system elements (a part of the MatLab/Simulink) is proposed. The model allows altering solar irradiation values for each solar cell of the module. The use of the model also makes it possible to obtain calculated values of voltages and currents at the photovoltic module output. In addition, the model provides the simulation of individual solar cells shading in the module. The developed Simulink model operates on the base of a well-known exponential dependence describing the volt-ampere characteristic of a photovoltaic module, and also takes into account the real circuit of the module with bypass diodes. The series resistance of the photovoltaic module is calculated by the subtraction between its experimental and theoretical volt-ampere characteristics for conditions that are close to normal. The Simulink model of the SF-P672300 module contains 72 nonlinear elements implemented on the basis of controlled current sources and connected in series. The model solved the problems of the algorithm stability for calculating algebraic cycles by introducing constraint the current and the voltage parameters. Experimental studies for the fully illuminated and partially shaded SF-P672300 module have demonstrated that the maximum relative error of the developed Simulink model does not exceed 15 %. Experimental and theoretical current-voltage characteristics of the SF-P672300 module under full illumination and partial shading are presented. The presented Simulink model may be used both at the design stage and at the operation stage of photovoltaic power plants in order to simulate and analyze the factors that affect the operation of them.

Modelling and Simulation of Solar Photovoltaic Cell for Different Insolation Values Based on MATLAB/Simulink Environment

2014 ◽  
Vol 550 ◽  
pp. 137-143 ◽  
Author(s):  
S. Narendiran ◽  
Sarat Kumar Sahoo
Keyword(s):  
Photovoltaic Cell ◽  
Photovoltaic Module ◽  
Solar Photovoltaic ◽  
Electrical Characteristics ◽  
Array Type ◽  
Matlab Simulink ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
Current Input ◽  
In Series

The paper discuss about the modelling and electrical characteristics of photovoltaic cell and its array type of construction in matlab-simulink environment at different insolation levels. The photovoltaic module is modelled using the diode electrical characteristic equation. The photovoltaic cell is analysed by voltage input and current input modules, The voltage and current input photovoltaic modules are simulated with different insolation values by varying the construction of PV modules. The results conclude that the current input PV module is well suited for applications were it shares same current when connected in series and voltage input PV module, where it shares same voltage when connected in parallel.

Hybrid Optimization Approach for Evaluating Photovoltaic Cell Parameters

2013 ◽  
Vol 373-375 ◽  
pp. 1261-1264
Author(s):  
Mei Ying Ye
Keyword(s):  
Cell Model ◽  
Computation Time ◽  
Photovoltaic Cell ◽  
Evaluation Procedure ◽  
Model Parameters ◽  
Optimization Approach ◽  
Problem Space ◽  
Local Optima ◽  
Cell Parameters ◽  
Intelligent Technique

A new hybrid intelligent technique is proposed to evaluate photovoltaic cell model parameters in this paper. The intelligent technique is based on a hybrid of genetic algorithm (GA) and LevenbergMarquardt algorithm (LMA). In the proposed hybrid intelligent technique, the GA firstly searches the entire problem space to get a set of roughly estimated solutions, i.e. near-optimal solutions. Then the LMA performs a local optima search in order to carry out further optimizations. An example has been used to demonstrate the evaluation procedure in order to test the performance of the proposed approach. The results show that the proposed technique has better performance than the GA approach in terms of the objective function value, the computation time and the reconstructedI-Vcurve shape.

scholarly journals Evaluation of Dust Elements on Photovoltaic Module Performance: an Experimental Study

2021 ◽  
Vol 6 ◽  
pp. 30
Author(s):  
Hussein A. Kazem ◽  
Miqdam T. Chaichan ◽  
Ali H.A. Al-Waeli ◽  
Kamaruzzaman Sopian ◽  
Abdul Salam K. Darwish
Keyword(s):  
Power Plants ◽  
Building Materials ◽  
Photovoltaic Performance ◽  
Geographic Location ◽  
Cell Voltage ◽  
Photovoltaic Cell ◽  
Natural Phenomenon ◽  
Photovoltaic Module ◽  
Dust Component ◽  
High Concentrations

Dust is a natural phenomenon, and it represents all the components suspended in the air. Dust causes the photovoltaic performance to deteriorate. The main dust components concentrations vary from one geographic location to another and from one season to another. These components also have different effects on the PV power losses. Therefore, studying the effect of the concentration of each dust component separately can give a greater clarification and detail of how the accumulated dust affects the behavior of the PV module. In this study, the dust accumulated on a photovoltaic cell was collected and analyzed into its basic components. The results showed that most of the dust of Sohar city consists mostly of sand (65%) coming from the Empty Quarter desert adjacent to the Al-Batinah region. Also, volatile building materials such as cement and gypsum have high concentrations in this dust, which are 5.25% and 4.94%, respectively. In addition, high concentrations of ash 4.92%, which is resulting from burning fuels in smelters, power plants, and refineries. The effect of most of the studied dust components was limited on the current of the photovoltaic cell, but their effect was clearer on the cell voltage. As a result, the decrease in power generation was especially evident in the case of ash, cement, and new garment, but the biggest decrease was due to sand. While iron powder and red sand had the least effect on the performance of the photovoltaic cell.

scholarly journals Estimation of Photovoltaic Cell Parameters Using Measurement Data of Photovoltaic Module String Currents and Voltages

2021 ◽  
Author(s):  
Shigeomi Hara ◽  
Hiroshi Douzono ◽  
Makoto Imamura
Keyword(s):  
Simulation Analysis ◽  
Cell Model ◽  
Measurement Data ◽  
String Model ◽  
Real Data ◽  
Photovoltaic Cell ◽  
Photovoltaic Module ◽  
Cell Parameters ◽  
Operating Environments ◽  
The Difference

Photovoltac (PV) models play an important role in the simulation analysis and fault diagnosis of PV systems. The<br>single diode model (SDM) is the most frequently used model in research and applications. There are numerous proposed methods to identify the SDM parameters. However, the characteristics of PV cells alter during the lifetime in normal operating environments; these variations may be due to degradation, faults, dust, weed, and so on. Therefore, it is crucial to estimate the actual parameters of the PV cells that represent those present state. The contribution of this study is to propose a method to estimate PV cell parameters on the basis of the measurement data regarding the currents and voltages of the PV module strings. A PV string model is described on the basis of the adaptive SDM for the PV cells in the system, and the parameters of each cell model are obtained by minimizing the difference between the measured string voltages and the string voltages computed by the model. The application of the proposed method to real data measured in a PV power plant is also presented to evaluate the proposed method.

scholarly journals Performance analysis of thermosyphon hybrid photovoltaic thermal collector

2016 ◽  
Vol 27 (1) ◽  
pp. 28 ◽  
Author(s):  
N. Marc-Alain Mutombo ◽  
Freddie Inambao ◽  
Glen Bright
Keyword(s):  
Solar Irradiance ◽  
Rectangular Channel ◽  
Environmental Parameters ◽  
Photovoltaic Module ◽  
The Sun ◽  
Cell Temperature ◽  
Solar Module ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
Incoming Energy

The conversion of solar irradiance into electricity by a photovoltaic module (PV) is 6– 7% of the incoming energy from the sun depending on the type of technology and the environmental parameters. More than 80% of incoming energy from the sun is reflected or absorbed by the solar module. The fraction of energy absorbed increases with solar cell temperature and the cells’ efficiency drops as a consequence. The efficiency of a PV module is improved by combining a PV module and a thermal collector in one unit, resulting in a hybrid photovoltaic and thermal collector (PV/T). The purpose of this paper is to present the behavior a thermosyphon hybrid PV/T when exposed to variations of environmental parameters and to demonstrate the advantage of cooling photovoltaic modules with water using a rectangular channel profile for the thermal collector. A single glazed flat-box absorber PV/T module was designed, its behavior for different environmental parameters tested, the numerical model developed, and the simulation for particular days for Durban weather run. The simulation result showed that the overall efficiency of the PV/T module was 38.7% against 14.6% for a standard PV module while the water temperature in the storage tank reached 37.1 °C. This is a great encouragement to the marketing of the PV/T technology in South Africa particularly during summer, and specifically in areas where the average annual solar irradiance is more than 4.70 kWh/m²/day.

Applied Technology in Simulation of Photovoltaic Cell Model Based on MATLAB/Simulink

2014 ◽  
Vol 662 ◽  
pp. 209-213
Author(s):  
Shuo Shi ◽  
Zhen Xiong Zhou
Keyword(s):  
Simulation Model ◽  
Cell Model ◽  
Photovoltaic Cell ◽  
Simulation Software ◽  
Pv System ◽  
Matlab Simulink ◽  
Simulink Simulation ◽  
Applied Technology ◽  
Different Types ◽  
Output Characteristics

According to the simplified mathematical model of photovoltaic cell, a kind of simulation model of Photovoltaic cell based on output characteristics is established by using MATLAB/Simulink simulation software in this paper. By using this model, the output characteristics of different types of photovoltaic cells can be simulated in different light intensity and temperature. This simulation model has a simple model structure, and the parameters of model are easy to be adjusted. Output characteristics of the photovoltaic cell can be accurately reflected, and provide a reference for the research of PV system.

scholarly journals Comparison of Performance Measurements of Photovoltaic Modules during Winter Months in Taxila, Pakistan

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Muhammad Anser Bashir ◽  
Hafiz Muhammad Ali ◽  
Shahid Khalil ◽  
Muzaffar Ali ◽  
Aysha Maryam Siddiqui
Keyword(s):  
Solar Irradiance ◽  
Strong Dependence ◽  
Performance Ratio ◽  
Back Surface ◽  
Photovoltaic Module ◽  
Comparative Performance ◽  
Solar Module ◽  
Photovoltaic Modules ◽  
And Performance ◽  
Module Efficiency

This paper presents the comparative performance evaluation of three commercially available photovoltaic modules (monocrystalline, polycrystalline, and single junction amorphous silicon) in Taxila, Pakistan. The experimentation was carried out at outdoor conditions for winter months. Power output, module efficiency, and performance ratio were calculated for each module and the effect of module temperature and solar irradiance on these parameters was investigated. Module parameters showed strong dependence on the solar irradiance and module temperature. Monocrystalline and polycrystalline modules showed better performance in high irradiance condition whereas it decreased suddenly with decrease in irradiance. Amorphous solar module also showed good performance in low irradiance due to its better light absorbing characteristics and thus showed higher average performance ratio. Monocrystalline photovoltaic module showed higher monthly average module efficiency and was found to be more efficient at this site. Module efficiency and performance ratio showed a decreasing trend with increase of irradiance and photovoltaic module back surface temperature.

scholarly journals Estimation of Photovoltaic Cell Parameters Using Measurement Data of Photovoltaic Module String Currents and Voltages

2021 ◽  
Author(s):  
Shigeomi Hara ◽  
Hiroshi Douzono ◽  
Makoto Imamura
Keyword(s):  
Simulation Analysis ◽  
Cell Model ◽  
Measurement Data ◽  
String Model ◽  
Real Data ◽  
Photovoltaic Cell ◽  
Photovoltaic Module ◽  
Cell Parameters ◽  
Operating Environments ◽  
The Difference

Photovoltac (PV) models play an important role in the simulation analysis and fault diagnosis of PV systems. The<br>single diode model (SDM) is the most frequently used model in research and applications. There are numerous proposed methods to identify the SDM parameters. However, the characteristics of PV cells alter during the lifetime in normal operating environments; these variations may be due to degradation, faults, dust, weed, and so on. Therefore, it is crucial to estimate the actual parameters of the PV cells that represent those present state. The contribution of this study is to propose a method to estimate PV cell parameters on the basis of the measurement data regarding the currents and voltages of the PV module strings. A PV string model is described on the basis of the adaptive SDM for the PV cells in the system, and the parameters of each cell model are obtained by minimizing the difference between the measured string voltages and the string voltages computed by the model. The application of the proposed method to real data measured in a PV power plant is also presented to evaluate the proposed method.

Sign in / Sign up

Export Citation Format

Share Document