scholarly journals The Influence of The Marine Bacillus Cereus Mc-1 Over Carbon Steel, Stainless Corrosion And Copper Coupons

2021 ◽  
Author(s):  
Paulo Moreira-Filho ◽  
Paloma de Paula da Silva Figueiredo ◽  
Artur Capão ◽  
Luciano Procópio
Keyword(s):  
Stainless Steel ◽  
Control System ◽  
Carbon Steel ◽  
Corrosion Rate ◽  
Bacillus Cereus ◽  
Copper Alloy ◽  
Culture Medium ◽  
316L Stainless Steel ◽  
Corrosion Rates ◽  
Nitrate Supplementation

Abstract The present study evaluated the influence of the marine bacteria Bacillus cereus Mc-1 on the corrosion of 1020 carbon steel, 316L stainless steel, and copper alloy. The Mc-1 strain was grown in a modified ammoniacal citrate culture medium (CFA.ico-), CFA.ico- with sodium nitrate supplementation (NO3-), and CFA.ico- with sodium chloride supplementation (NaCl). The and mass loss and corrosion rate were evaluated after the periods of seven, 15, and 30 days. The results showed that in CFA.ico- and CFA.ico- medium added NO3- the corrosion rates of carbon steel and copper alloy were high when compared to the control. Whereas the medium was supplemented with NaCl, despite the rates being above the averages of the control system, they were considerably below the previous results. In general, the corrosion rates induced by Mc-1 on 316L coupons were below the results compared to carbon steel and copper alloy. When analyzing the corrosion rate measurements, regardless of the culture medium, the corrosion levels decreased consistently after 15 days, being below the levels evaluated after seven days of the experiment. Our analyzes suggest that B. cereus Mc-1 has different influences on corrosion in different metals and environmental conditions, such as the presence of NO3- and NaCl. These results can help to better understand the influence of this bacteria genus on the corrosion of metals in marine environments.

Corrosion of Aluminized Steel in Seawater

2004 ◽  
Author(s):  
Hiroki Kimoto
Keyword(s):  
Stainless Steel ◽  
Carbon Steel ◽  
Corrosion Rate ◽  
Flow Rate ◽  
Galvanic Corrosion ◽  
Al Alloy ◽  
Corrosion Rates ◽  
Aluminized Steel ◽  
Alloy Carbon ◽  
Galvanic Couples

The influence of flow rate of seawater on the corrosion rate of hot-dipped aluminized steel in seawater was investigated using the following galvanic couples: aluminum/carbon steel, aluminum/Fe-Al alloy, aluminum/stainless steel, Fe-Al alloy/carbon steel, Fe-Al alloy/stainless steel, and carbon steel/stainless steel. The corrosion rate of aluminum in all the couples was greater than that of aluminum not connected with other metals. The corrosion rates increased in the following order: aluminum/carbon steel > aluminum/stainless steel > aluminum/Fe-Al alloy. Aluminum connected with carbon steel had the greatest corrosion rate: seven times of the rate of aluminum that was not connected with other metals. The galvanic corrosion rate of carbon steel is 1.9 to 2.5 times greater than that of carbon steel that is not connected with other metals.

The corrosion behavior of ferrous materials immersed in acidic-media using D-optimal design

2019 ◽  
Vol 16 (4) ◽  
pp. 647-656 ◽  
Author(s):  
Daniel Obregón Valencia ◽  
Halter García Sánchez ◽  
Isabel Díaz Tang
Keyword(s):  
Stainless Steel ◽  
Carbon Steel ◽  
Optimal Design ◽  
Corrosion Rate ◽  
Response Surface ◽  
Ferric Chloride ◽  
Chloride Solutions ◽  
Content Type ◽  
Corrosion Rates ◽  
Steel Aisi

Purpose The purpose of this paper is to model the corrosion rate behavior for two ferrous materials, carbon steel AISI 1020 and stainless steel AISI 304, immersed in ferric sulfate and ferric chloride solutions using D-optimal design with response surface methodology. Design/methodology/approach Experimental design addresses two factors (concentration and contact time) with multilevel categories, in order to predict and compare the corrosion rates of the studied materials immersed in flocculants solutions. A corrosion rate of specimens was calculated from mass loss determinations. Findings The authors used a polynomial model to fit the experimental values, thereby predicting significantly higher corrosion rates in ferric chloride solutions, as compared to ferric sulfate. Originality/value The authors propose a high fidelity model of the corrosion rate of each carbon steel and stainless steel material using D-optimal design with a response surface method (RSM).

The Corrosion of Carbon Steel and Stainless Steel in Simulated Geothermal Media

1985 ◽  
Vol 38 (8) ◽  
pp. 1133 ◽  
Author(s):  
BG Pound ◽  
MH Abdurrahman ◽  
MP Glucina ◽  
GA Wright ◽  
RM Sharp
Keyword(s):  
Carbon Steel ◽  
Corrosion Rate ◽  
Stainless Steels ◽  
Polarization Resistance ◽  
Iron Sulfide ◽  
Low Carbon Steel ◽  
Passive Films ◽  
Low Carbon ◽  
Corrosion Rates ◽  
Good Agreement

The corrosion rates of low-carbon steel, and 304, 316 and 410/420 stainless steels in simulated geothermal media containing hydrogen sulfide have been measured by means of the polarization resistance technique. Good agreement was found between weight-loss and polarization resistance measurements of the corrosion rate for all the metals tested. Carbon steel formed a non-adherent film of mackinawite (Fe1 + xS). The lack of protection afforded to the steel by the film resulted in an approximately constant corrosion rate. The stainless steels also exhibited corrosion rates that were independent of time. However, the 410 and 420 alloys formed an adherent film consisting mainly of troilite ( FeS ) which provided only limited passivity. In contrast, the 304 and 316 alloys appeared to be essentially protected by a passive film which did not seem to involve an iron sulfide phase. However, all the stainless steels, particularly the 410 and 420 alloys, showed pitting, which indicated that some breakdown of the passive films occurred.

scholarly journals The effect of volatile organic acids and CO2 on the corrosion rate of carbon steel from a Top-of-Line-Corrosion (TLC) perspective

2021 ◽  
Vol 1201 (1) ◽  
pp. 012079
Author(s):  
S B Gjertsen ◽  
A Palencsar ◽  
M Seiersten ◽  
T H Hemmingsen
Keyword(s):  
Carbon Steel ◽  
Corrosion Rate ◽  
Organic Acid ◽  
Carbonic Acid ◽  
Acid Corrosion ◽  
Iron Concentration ◽  
Critical Factor ◽  
Steel Corrosion ◽  
Carbon Steels ◽  
Corrosion Rates

Abstract Models for predicting top-of-line corrosion (TLC) rates on carbon steels are important tools for cost-effectively designing and operating natural gas transportation pipelines. The work presented in this paper is aimed to investigate how the corrosion rates on carbon steel is affected by acids typically present in the transported pipeline fluids. This investigation may contribute to the development of improved models. In a series of experiments, the corrosion rate differences for pure CO2 (carbonic acid) corrosion and pure organic acid corrosion (acetic acid and formic acid) on X65 carbon steel were investigated at starting pH values; 4.5, 5.3, or 6.3. The experiments were conducted in deaerated low-salinity aqueous solutions at atmospheric pressure and temperature of 65 °C. The corrosion rates were evaluated from linear polarization resistance data as well as mass loss and released iron concentration. A correlation between lower pH values and increased corrosion rates was found for the organic acid experiments. However, the pH was not the most critical factor for the rates of carbon steel corrosion in these experiments. The experimental results showed that the type of acid species involved and the concentration of the undissociated acid in the solution influenced the corrosion rates considerably.

scholarly journals Corrosion Evaluation of 316L Stainless Steel in CNT-Water Nanofluid: Effect of CNTs Loading

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1634 ◽  
Author(s):  
Dana H. Abdeen ◽  
Muataz A. Atieh ◽  
Belabbes Merzougui ◽  
Walid Khalfaoui
Keyword(s):  
Stainless Steel ◽  
Corrosion Rate ◽  
316L Stainless Steel ◽  
Tap Water ◽  
Gum Arabic ◽  
Corrosion Performance ◽  
Free Energy Of Adsorption ◽  
Sem Images ◽  
Pitting Potential ◽  
Water Solutions

Polarization resistance and potentiodynamic scan testing were performed on 316L stainless steel (SS) at room temperature in carbon nanotube (CNT)-water nanofluid. Different CNT loadings of 0.05, 0.1, 0.3 and 0.5 wt% were suspended in deionized water using gum arabic (GA) surfactant. Corrosion potential, Tafel constants, corrosion rates and pitting potential values indicated better corrosion performance in the presence of CNTs with respect to samples tested in GA-water solutions. According to Gibbs free energy of adsorption, CNTs were physically adsorbed into the surface of the metal, and this adsorption followed Langmuir adsorption isotherm type II. Samples tested in CNT nanofluid revealed a corrosion performance comparable to that of tap water and better than that for GA-water solutions. Among all samples tested in CNT nanofluids, the lowest corrosion rate was attained with 0.1 wt% CNT nanofluid, while the highest value was obtained with 0.5 wt% CNT nanofluid. At higher CNT concentrations, accumulated CNTs might form active anodic sites and increase the corrosion rate. SEM images for samples of higher CNT loadings were observed to have higher pit densities and diameters.

Influence of Electromagnetic Treatment on Corrosion Behavior of Carbon Steel and 316L Stainless Steel in Simulated Cooling Water

2011 ◽  
Vol 347-353 ◽  
pp. 3135-3138
Author(s):  
Hong Hua Ge ◽  
Jie Ting Tao ◽  
Xiao Ming Gong ◽  
Cheng Jun Wei ◽  
Xue Min Xu
Keyword(s):  
Stainless Steel ◽  
Carbon Steel ◽  
Corrosion Behavior ◽  
316L Stainless Steel ◽  
Cooling Water ◽  
Stainless Steel Electrode ◽  
Transfer Resistance ◽  
Steel Electrode ◽  
Pitting Potential ◽  
Electromagnetic Treatment

Abstract: The effect of electromagnetic treatment on corrosion behavior of carbon steel and stainless steel in simulated cooling water was investigated by electrochemical impedance spectroscopy, potentiodynamic polarization techniques and water analysis. It was found that the charge transfer resistance decreased and the corrosion current density increased after electromagnetic treatment for carbon steel electrode, which shows that such treatment promotes corrosion of carbon steel in simulated cooling water. In contrast, the pitting potential of 316L stainless steel electrode rose which revealed that electromagnetic treatment of the experimental water exhibited corrosion inhibition to 316L stainless steel. Reasons for different corrosion behavior of the two metals were discussed.

Effect of Filler Metals on the Microstructures and Mechanical Properties of Dissimilar Low Carbon Steel and 316L Stainless Steel Welded Joints

2015 ◽  
Vol 819 ◽  
pp. 57-62 ◽  
Author(s):  
M.F. Mamat ◽  
E. Hamzah ◽  
Z. Ibrahim ◽  
A.M. Rohah ◽  
A. Bahador
Keyword(s):  
Stainless Steel ◽  
Carbon Steel ◽  
Base Metal ◽  
Arc Welding ◽  
316L Stainless Steel ◽  
Filler Metal ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Steel Base ◽  
Welding Electrode

In this paper, dissimilar joining of 316L stainless steel to low carbon steel was carried out using gas metal arc welding (GMAW) and gas tungsten arc welding (GTAW). Samples were welded using AWS: ER309L welding electrode for GMAW and AWS: ER316L welding electrode for GTAW process. Determination of mechanical properties and material characterization on the welded joints were carried out using the Instron tensile test machine and an optical microscope respectively. The cross section area of the welded joint consists of three main areas namely the base metal (BM), heat affected zone (HAZ), and weld metal (WM). It was found that, the yield and tensile strengths of welded samples using ER316L filler metal were slightly higher than the welded sample using ER309L welding electrode. All welded samples fractured at low carbon steel base metal indicating that the regions of ER316L stainless steel base metal, ER316L filler metal and heat affected zone (HAZ) have a higher strength than low carbon steel base metal. It was also found that ER316L welding electrode was the best filler to be used for welding two dissimilar metals between carbon and stainless steel.

Synergistic Effect of Thiourea and Surfactants on Corrosion Inhibition of Stainless Steel-410 in Presence of Sulfuric Acid

2014 ◽  
Vol 699 ◽  
pp. 186-191 ◽  
Author(s):  
Sami Ullah ◽  
Mohd Shariff Azmi ◽  
Muhammad Nadeem ◽  
Mohammad Azmi Bustam ◽  
Shaukat Ali Shahid ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Sulfuric Acid ◽  
Corrosion Rate ◽  
Corrosion Inhibition ◽  
Sodium Dodecyl ◽  
Ammonium Bromide ◽  
Inhibitor Concentration ◽  
Corrosion Rates ◽  
Inhibition Performance ◽  
Triton X

The inhibition of corrosion of stainless steel (SS)-410 in sulfuric acid using thiourea and three different surfactants, cetyle trimethyl ammonium bromide (CTAB), sodium dodecyl sulfate (SDS) and X-Triton was studied. Corrosion rates were determined by using corrosion coupons. The corrosion rate was found to be decreased with increase in inhibitor concentration. It was observed that the maximum corrosion inhibition occurred in the post micellar concentration of the surfactants. By optimizing the corrosion inhibition performance of different blends of surfactants and thiourea in 3 M H2SO4,the corrosion inhibition order was found as: Triton X-100 + thiourea > CTAB + thiourea > SDS + thiourea. The best results obtained by the addition of 200 ppm thiourea in 500 ppm of Triton X-100 in 3 M H2SO4acid solution. This blend decreased the corrosion rate of SS-410 to 657.66 mpy.

Apparent Inversion of the Effect of Alloyed Molybdenum for Corrosion of Ordinary and Enhanced 316L Stainless Steel in Sulfuric Acid

2008 ◽  
Vol 1107 ◽  
Author(s):  
Gloria Kwong ◽  
Anatolie Carcea ◽  
Roger C. Newman
Keyword(s):  
Stainless Steel ◽  
Carbon Steel ◽  
Corrosion Test ◽  
316L Stainless Steel ◽  
Storage System ◽  
Electrochemical Corrosion ◽  
Premature Failure ◽  
316L Steel ◽  
Electrochemical Corrosion Test ◽  
Spent Resin

AbstractAn aging assessment of the OPG waste resin storage system predicted the potential for premature failure of the carbon steel resin liners. Consequently, resin liners made of 316L stainless steel with a minimum content of 2.5% molybdenum were selected to replace the carbon steel liners. The 2.5% Mo 316L stainless steel was specified to enhance pitting resistance in the spent resin environment. With the additional Mo, one would expect that a brief electrochemical corrosion test will reveal the superiority of such alloy over conventional 316L steel. This study reports a contrary experience

Sign in / Sign up

Export Citation Format

Share Document