Organic Stabilization and Nitrogen Removal in Membrane Separation Bioreactor for Domestic Wastewater Treatment

1992 ◽  
Vol 25 (10) ◽  
pp. 231-240 ◽  
Author(s):  
C. Chiemchaisri ◽  
Y. K. Wong ◽  
T. Urase ◽  
K. Yamamoto
Keyword(s):  
Total Nitrogen ◽  
Nitrogen Removal ◽  
Hollow Fiber ◽  
Membrane Separation ◽  
Hollow Fiber Membrane ◽  
Membrane Surface ◽  
Aeration Tank ◽  
Intermittent Aeration ◽  
Permeate Flux ◽  
Fiber Membrane

In this study, organic stabilization and nitrogen removal were investigated using a household type hollow fiber membrane separation bioreactor of 6 2 1 volume. The process employed direct solid-liquid separation by hollow fiber membrane inside an activated sludge aeration tank. By providing highly turbulent conditions within the separation zone in conjunction with Jet aerating installation inside the membrane module, sludge accumulation on the membrane surface and inside the module can be reduced. Permeate flux obtained after 330 days of operation was 0.2 m/d under intermittent suction. High degree of organic stabilization was obtained in the system by operation without sludge wastage except for sampling purposes. Continuous and intermittent aeration modes were investigated in the study. The average effluent COD concentration of 20.8 and 16.5 mg/l were observed during continuous and intermittent aerating application respectively. Degree of nitrification depended upon DO concentration of mixed liquor during aeration period. Introduction of intermittent aeration enhanced total nitrogen removal up to 80% or more by simultaneous nitrification and denitrification, resulting in average of 4.9 mg/l of total nitrogen in the effluent. Increase in DO in aeration period from 1.5–2 mg/l to 4–5 mg/l improved percentage of nitrogen removal to more than 90%. Rejection of 4–6 log virus concentration by gel layer formed on the membrane surface was also observed.

scholarly journals Modification of porous polyetherimide hollow fiber membrane by dip-coating of Zonyl® BA for membrane distillation of dyeing wastewater

2021 ◽  
Author(s):  
S. A. Mousavi ◽  
Z. Arab Aboosadi ◽  
A. Mansourizadeh ◽  
B. Honarvar
Keyword(s):  
Pore Size ◽  
Hollow Fiber ◽  
Hollow Fiber Membrane ◽  
Membrane Surface ◽  
Pure Water ◽  
Dip Coating ◽  
Membrane Distillation ◽  
Permeate Flux ◽  
Fiber Membrane ◽  
Air Gap Membrane Distillation

Abstract Wetting and fouling have significantly affected the application of membrane distillation (MD). In this work, a dip-coating method was used for improving surface hydrophobicity of the polyetherimide (PEI) hollow fiber membrane. An air gap membrane distillation (AGMD) process was applied for treatment of the methylene blue (MB) solution. The porous PEI membrane was fabricated by a dry-wet spinning process and the hydrophobic 2-(Perfluoroalkyl) ethanol (Zonyl® BA) was used as the coating material. From FESEM, the modified PEI-Zonyl membrane showed an open structure with large finger-like cavities. The modified membrane displayed a narrow pore size distribution with mean pore size of 0.028 μm. The outer surface contact angle of the PEI-Zonly membrane increased from 81.3° to 100.4° due to the formation of an ultra-thin coated layer. The pure water flux of the PEI-Zonyl membrane was slightly reduced compared to the pristine PEI membrane. The permeate flux of 6.5 kg/m2 h and MB rejection of 98% was found for the PEI-Zonyl membrane during 76 h of the AGMD operation. Adsorption of MB on the membrane surface was confirmed based on the Langmuir isotherm evaluation, AFM and FESM analysis. The modified PEI-Zonyl membrane can be a favorable alternative for AGMD of dyeing wastewaters.

scholarly journals Applying a Hydrophilic Modified Hollow Fiber Membrane to Reduce Fouling in Artificial Lungs

Separations ◽  
2021 ◽  
Vol 8 (8) ◽  
pp. 113
Author(s):  
Nawaf Alshammari ◽  
Meshari Alazmi ◽  
Vajid Nettoor Veettil
Keyword(s):  
Gas Exchange ◽  
Hollow Fiber ◽  
Hollow Fiber Membrane ◽  
Membrane Surface ◽  
Artificial Lung ◽  
Hollow Fiber Membranes ◽  
Fiber Membrane ◽  
Hydrophilic Modification ◽  
Protein Fouling ◽  
Time Periods

Membranes for use in high gas exchange lung applications are riddled with fouling. The goal of this research is to create a membrane that can function in an artificial lung until the actual lung becomes available for the patient. The design of the artificial lung is based on new hollow fiber membranes (HFMs), due to which the current devices have short and limited periods of low fouling. By successfully modifying membranes with attached peptoids, low fouling can be achieved for longer periods of time. Hydrophilic modification of porous polysulfone (PSF) membranes can be achieved gradually by polydopamine (PSU-PDA) and peptoid (PSU-PDA-NMEG5). Polysulfone (PSU-BSA-35Mg), polysulfone polydopamine (PSUPDA-BSA-35Mg) and polysulfone polydopamine peptoid (PSU-PDA-NMEG5-BSA35Mg) were tested by potting into the new design of gas exchange modules. Both surfaces of the modified membranes were found to be highly resistant to protein fouling permanently. The use of different peptoids can facilitate optimization of the low fouling on the membrane surface, thereby allowing membranes to be run for significantly longer time periods than has been currently achieved.

Steady three-dimensional flows past hollow fiber membrane arrays – cross flow arrangement

2018 ◽  
Vol 96 (12) ◽  
pp. 1272-1287 ◽  
Author(s):  
Mustafa Usta ◽  
Michael Morabito ◽  
Mohammed Alrehili ◽  
Alaa Hakim ◽  
Alparslan Oztekin
Keyword(s):  
Hollow Fiber ◽  
Hollow Fiber Membrane ◽  
Flow Behavior ◽  
Membrane Surface ◽  
Three Dimensional ◽  
Cross Flow ◽  
Coefficient Of Performance ◽  
Fiber Membrane ◽  
Cfd Simulations ◽  
Flow Configuration

Hollow fiber membrane (HFM) modules are among the most common separation devices employed in membrane separation applications. Three-dimensional steady-state computational fluid dynamics (CFD) simulations are carried out to study flow past hollow fiber membrane banks (HFMB). The current study investigates the effects of flow behavior on membrane performance during binary mixture separations. Carbon dioxide (CO2) removal from methane (CH4) is examined for various arrangements of HFMs in staggered and inline configurations. The common HFM module arrangement is the axial flow configuration. However, this work focuses on the radial cross-flow configuration. The HFM surface is a functional boundary where the suction rate and concentration of each species are coupled and are functions of the local partial pressures, the permeability, and the selectivity of the HFM. CFD simulations employed the turbulent k–ω shear stress transport (SST) model to study HFM performance for Reynolds numbers, 200 ≤ Re ≤ 1000. The efficiency of the inline and staggered arrangements in the separation module is evaluated by the coefficient of performance and the rate of mass flow per unit area of CO2 passing across the membrane surface. This work demonstrates that the module with staggered arrangement outperforms the module with the inline arrangement.

Micro-aeration with hollow fiber membrane enhanced the nitrogen removal in constructed wetlands

2019 ◽  
Vol 27 (21) ◽  
pp. 25877-25885 ◽  
Author(s):  
Xinshan Song ◽  
Yufeng Zhao ◽  
Yuhui Wang ◽  
Zhihao Si ◽  
Xiaoyan Ge ◽  
...  
Keyword(s):  
Constructed Wetlands ◽  
Nitrogen Removal ◽  
Hollow Fiber ◽  
Hollow Fiber Membrane ◽  
Fiber Membrane

Hydrophilic Modification of PES Hollow Fiber Membrane via Surface-Initiated Atom Transfer Radical Polymerization

2010 ◽  
Vol 150-151 ◽  
pp. 565-570 ◽  
Author(s):  
Yong Bo Shen ◽  
Ya Tao Zhang ◽  
Jian Hua Qiu ◽  
Yan Wu Zhang ◽  
Hao Qin Zhang
Keyword(s):  
Atom Transfer Radical Polymerization ◽  
Radical Polymerization ◽  
Hollow Fiber ◽  
Polymer Brushes ◽  
Hollow Fiber Membrane ◽  
Membrane Surface ◽  
Pure Water ◽  
Average Molecular Weight ◽  
Atom Transfer ◽  
Fiber Membrane

Hydrophilic poly((poly(ethylene glycol) methyl ether methacrylate) (P(PEGMA)) brushes were grafted from chloromethylated polyethersulfone (CMPES) hollow fiber membrane surface by surface-initiated atom transfer radical polymerization(SI-ATRP) to improve the membrane’s hydrophilic property. The CMPES hollow fiber membrane was prepared by phase inversion process. The benzyl chloride groups on the CMPES membrane surface could afford effective macroinitiators for grafting the well-defined polymer brushes. Attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy confirmed the grafting of P (PEGMA) chains. Field emission scanning electron microscopy (FESEM) was used to characterize the surface morphology of the CMPES membrane and modified membrane. The grafting yield of P (PEGMA) was determined by weight gain measurement. The results showed that the number-average molecular weight (Mn) of P (PEGMA) increased with the polymerization time. It was found that the grafting of P (PEGMA) brought higher pure water flux, improved water uptake ratio and better anti-protein absorption ability to CMPES membrane after modification.

Sign in / Sign up

Export Citation Format

Share Document