scholarly journals Heterogeneous selenite reduction by zero valent iron steel wool

2016 ◽  
Vol 75 (4) ◽  
pp. 908-915 ◽  
Author(s):  
Ziyan Li ◽  
Donglin Huang ◽  
Louis M. McDonald
Keyword(s):  
Photoelectron Spectroscopy ◽  
Mine Drainage ◽  
Critical Factor ◽  
Zero Valent Iron ◽  
Spectroscopic Techniques ◽  
Steel Wool ◽  
Solution Ph ◽  
Selenite Reduction ◽  
Heterogeneous Reduction ◽  
Low Sulfur

Mine drainage from the low-sulfur surface coal mines in southern West Virginia, USA, is circumneutral (pH > 6) but contains elevated selenium (Se) concentrations. Removal of selenite ions from aqueous solutions under anoxic condition at pH 6–8.5 by zero valent iron steel wool (ZVI-SW) was investigated in bench-scale kinetic experiments using wet chemical, microscopic and spectroscopic techniques (X-ray photoelectron spectroscopy). ZVI-SW could effectively and efficiently remove SeIV from solution with pH 6–8.5. A two-step removal mechanism was identified for SeIV reduction by ZVI-SW. The proposed mechanism was electrochemical reduction of SeIV by Fe0 in an initial lag stage, followed by a faster heterogeneous reduction, mediated by an FeII-bearing phase (hydroxide or green rust). Solution pH was a critical factor for the kinetic rate in the lag stage (0.33 h−1 for pH > 8 and 0.10 h−1 for pH 6–8). The length of lag stage was 20–30 min as determined by the time for dissolved FeII concentration to reach 0.30 ± 0.04 mg L−1 which was critical for induction of the faster stage. About 65% of the initial SeIV was reduced to Se0, the primary reductive product in both stages.

scholarly journals Preparation of magnetic carbon/Fe3O4 supported zero-valent iron composites and their application in Pb(II) removal from aqueous solutions

2017 ◽  
Vol 76 (10) ◽  
pp. 2680-2689 ◽  
Author(s):  
Kaixuan Ma ◽  
Qiu Wang ◽  
Qianyun Rong ◽  
Dapeng Zhang ◽  
Shihai Cui ◽  
...  
Keyword(s):  
Removal Efficiency ◽  
Photoelectron Spectroscopy ◽  
Low Cost ◽  
Zero Valent Iron ◽  
Solution Ph ◽  
Environmental Friendliness ◽  
X Ray ◽  
Transmission Electron ◽  
Reduction Methods ◽  
Magnetic Carbon

Abstract Nanoscale zero-valent iron (NZVI) was first assembled on magnetic carbon/Fe3O4 (CM) with a combination of hydrothermal and liquid phase reduction methods. The novel NZVI@CM magnetic nanocomposites have the merits of large surface area, unique magnetic property, low cost and environmental friendliness. They can be used for Pb(II) removal in aqueous solution. The materials were characterized by using transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform-infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), vibrating sample magnetometry (VSM), X-ray photoelectron spectroscopy (XPS) and Brunauer–Emmett–Teller (BET) adsorption. The various parameters, such as reaction time, dosage of catalyst, solution pH and acid ions concentrations were studied. The removal efficiency of Pb(II) can be obviously increased by the combination of appropriate CM and NZVI. The removal efficiency of Pb(II) is 99.7% by using 60 mg of NZVI@CM at pH 7. The kinetics study indicates that the Pb(II) removal accords to pseudo-second-order kinetics model.

Preparation of Novel Ag–Si–TiO2 Composite and Research on Its Photocatalytic Degradation of Formaldehyde

2021 ◽  
Vol 13 (3) ◽  
pp. 371-380
Author(s):  
Yongjun Wu ◽  
Nina Xie ◽  
Lu Yu
Keyword(s):  
Photoelectron Spectroscopy ◽  
Removal Rate ◽  
Sol Gel ◽  
Catalytic Performance ◽  
Formaldehyde Concentration ◽  
Order Kinetic ◽  
Solution Ph ◽  
Visible Absorption ◽  
X Ray ◽  
Co Doped

A novel Ag–Si–TiO2 composite was prepared via sol–gel method for removing residual formaldehyde in shiitake mushroom. The structure of Ag–Si–TiO2 composite was characterized by scanning electron microscope (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analyses. Ultraviolet-visible absorption spectroscopy (UV-Vis) and N2 adsorption-desorption tests showed that Ag and Si co-doped decreased the band gap, the Brunauer-Emmett-Teller (BET) specific surface area of the samples increased and the recombination probability of electron-hole pairs (e--h+) reduced. Effect on removal rate of formaldehyde with different Ag-Si co-doped content, formaldehyde concentration and solution pH were investigated, and the results showed that 6.0 wt%Ag-3.0 wt%Si-TiO2 samples had an optimum catalytic performance, and the degradation efficiency reached 96.6% after 40 W 365 nm UV lamp irradiation for 360 min. The kinetics of formaldehyde degradation by Ag–Si–TiO2 composite photocatalyst could be described by Langmuir-Hinshelwood first-order kinetic model.

scholarly journals Fenton Degradation of Ofloxacin Using a Montmorillonite-Fe3O4 Composite

2020 ◽  
Vol 2 (1) ◽  
pp. 32
Author(s):  
Alamri Rahmah Dhahawi Ahmad ◽  
Saifullahi Shehu Imam ◽  
Wen Da Oh ◽  
Rohana Adnan
Keyword(s):  
Electron Microscope ◽  
Photoelectron Spectroscopy ◽  
High Efficiency ◽  
Solar Irradiation ◽  
Precipitation Process ◽  
Wastewater Remediation ◽  
Solution Ph ◽  
X Ray ◽  
Subsequent Degradation ◽  
Co Precipitation

In this work, FeM composites consisting of montmorillonite and variable amounts of Fe3O4 were successfully synthesized via a facile co-precipitation process. They were characterized using X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscope (FESEM), energy dispersive X-ray spectroscopy (EDX), transmission electron microscope (TEM), N2 adsorption-desorption, and Fourier transform infrared spectroscopy (FT-IR) techniques to explain the effect of Fe3O4 content on the physicochemical properties of the Fe3O4-montmorillonite (FeM) composites. The FeM composites were subsequently used as heterogeneous Fenton catalysts to activate green oxidant (H2O2) for the subsequent degradation of ofloxacin (OFL) antibiotic. The efficiency of the FeM composites was studied by varying various parameters of Fe3O4 loading on montmorillonite, catalyst dosage, initial solution pH, initial OFL concentration, different oxidants, H2O2 dosage, reaction temperature, inorganic salts, and solar irradiation. Under the conditions of 0.75 g/L FeM-10, 5 mL/L H2O2, and natural pH, almost 81% of 50 mg/L of OFL was removed within 120 min in the dark, while total organic carbon (TOC) reduction was about 56%. Moreover, the FeM-10 composite maintained high efficiency and was stable even after four continuous cycles, making it a promising candidate in real wastewater remediation.

A Facile Strategy to Fabricate Nanoscale Zero-Valent Iron Decorated Graphene Oxide Composite for Dechloridation of Trichloroacetic Acid in Water

2018 ◽  
Vol 18 (12) ◽  
pp. 8252-8257 ◽  
Author(s):  
Huixuan Zhang ◽  
Xinyi Zhang ◽  
Ruonan Guo ◽  
Qingfeng Cheng ◽  
Xiuwen Cheng
Keyword(s):  
Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Sewage Treatment ◽  
Reduction Process ◽  
Zero Valent Iron ◽  
Chlorinated Organic Compounds ◽  
X Ray ◽  
Transmission Electron ◽  
Nanoscale Zero Valent Iron ◽  
Adsorption Desorption

In this study, nanoscale zero-valent iron decorated graphene oxide (NZVI/GO) composite was fabricated through a reduction process in the presence of sodium borohydride (NaBH4) solution. Subsequently, physicochemical properties of the NZVI/GO composites were characterized by scanning electron microscope (SEM), transmission electron microscopy (TEM), N2 adsorption/desorption, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transformation infrared spectroscopy (FT-IR) and Raman spectra. Results indicated that Fe species existed in the form of Fe0, which uniformly dispersed on the surface of GO. Furthermore, the performance of NZVI/GO was evaluated by the degradation of tichloroacetic acid (TCAA). TCAA can be rapidly degraded by NZVI/GO. This paper provides a promising strategy to synthesize versatile catalyst which would be potentially applied in sewage treatment to degrade chlorinated organic compounds.

scholarly journals Synthesis of Nanoscale Zerovalent Iron (nZVI) Supported on Biochar for Chromium Remediation from Aqueous Solution and Soil

2019 ◽  
Vol 16 (22) ◽  
pp. 4430 ◽  
Author(s):  
Haixia Wang ◽  
Mingliang Zhang ◽  
Hongyi Li
Keyword(s):  
Aqueous Solution ◽  
Photoelectron Spectroscopy ◽  
Zero Valent Iron ◽  
Zerovalent Iron ◽  
X Ray ◽  
Nanoscale Zerovalent Iron ◽  
Before And After ◽  
Pseudo Second Order ◽  
Xrd Patterns ◽  
Co Precipitation

Maize straw biochar-supported nanoscale zero-valent iron composite (MSB-nZVI) was prepared for efficient chromium (Cr) removal through alleviating the aggregation of zero-valent iron particles. The removal mechanism of MSB-nZVI was investigated by scanning electron microscopy with energy dispersive X-ray (SEM-EDX), X-ray diffractometry (XRD), and X-ray photoelectron spectroscopy (XPS). Cr(VI) removal from aqueous solution by MSB-nZVI was greatly affected by pH and initial concentration. The removal efficiency of Cr(VI) decreased with increasing pH, and the removal kinetics followed the pseudo-second-order model. XRD patterns of MSB-nZVI before and after reaction showed that reduction and precipitation/co-precipitation (FeCr2O4, Fe3O4, Fe2O3) occurred with the conversion of Cr(VI) to Cr(III) and Fe(0) to Fe(II)/Fe(III). The produced precipitation/co-precipitation could be deposited on the MSB surface rather than being only coated on the surface of nZVI particles, which can alleviate passivation of nZVI. For remediation of Cr(VI)-contaminated saline–alkali soil (pH 8.6–9.0, Cr 341 mg/kg), the released amount of Cr(VI) was 70.7 mg/kg, while it sharply decreased to 0.6–1.7 mg/kg at pH 4.0–8.0, indicating that the saline–alkali environment inhibited the remediation efficiency. These results show that MSB-nZVI can be used as an effective material for Cr(VI) removal from aqueous solution and contaminated soil.

scholarly journals Removal efficiency of hexavalent chromium from wastewater using starch-stabilized nanoscale zero-valent iron

2019 ◽  
Vol 80 (6) ◽  
pp. 1076-1084 ◽  
Author(s):  
Hualin Chen ◽  
Huajun Xie ◽  
Jiangmin Zhou ◽  
Yueliang Tao ◽  
Yongpu Zhang ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
High Reactivity ◽  
Zero Valent Iron ◽  
X Ray Diffraction ◽  
X Ray ◽  
Phase Reduction ◽  
Nanoscale Zero Valent Iron ◽  
Removal Efficiencies ◽  
Ph Range ◽  
Uniform Particle Size

Abstract In this study, starch-stabilized nanoscale zero-valent iron (S-nZVI) was produced using the liquid-phase reduction method. It was used to remove chromium from wastewater, and compared to a commercial nanoscale zero-valent iron (C-nZVI). Both nZVIs were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The characterization results showed that S-nZVI had smaller particles and a more uniform particle size distribution than C-nZVI. Both nZVIs showed a core-shell structure with the Fe0 core prominently surrounded by less iron oxides of Fe2+ and Fe3+. The optimal application methods to remove Cr(VI) from wastewater were also explored. The results showed that both the removal efficiencies of total Cr and Cr(VI) increased with increases in the addition of nZVIs, while the removal efficiencies of total Cr and Cr(VI) by S-nZVI were clearly higher than that of C-nZVI, especially in a low pH range (pH = 1.0–6.0). This research indicated that starch-stabilized nanoscale zero-valent iron is a valuable material to remove heavy metals from wastewater due to its stability and high reactivity.

Recyclable Heterogeneous Fe-Mo Nanocatalyst: Application in Solvent Free Synthesis of β-enaminones

2019 ◽  
Vol 6 (3) ◽  
pp. 238-247
Author(s):  
Swapnil R. Bankar
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Significant Loss ◽  
Solvent Free ◽  
Catalyst Loading ◽  
Spectroscopic Techniques ◽  
Impregnation Method ◽  
Molybdenum Catalyst ◽  
X Ray ◽  
Solvent Free Condition

<P>Background: In recent years, green organic transformation has become a challenge for a chemist in areas like social sector, health, and environment. Literature survey revealed that a nano magnetite supported heterogeneous catalysis is an emergent field with huge application in chemical synthesis. </P><P> Objective: In the present article, the aim was to develop a simple and facile method to carry organic reaction under benign media. So, the focus was on the synthesis of nano-magnetite supported molybdenum catalyst and its application in β-enaminones synthesis. </P><P> Methods: Magnetically recyclable heterogeneous ferrite-molybdenum catalyst was prepared by simple impregnation method. The synthesized nanocatalyst Fe-Mo was well analysed by spectroscopic techniques like X-ray diffraction analysis, X-ray photoelectron spectroscopy, transmission electron microscopy, field-emission gun scanning electron microscopy and vibrating-sample magnetometry. The functionalized nanocatalyst Fe-Mo was employed in the synthesis of β-enaminones under solvent free condition. </P><P> Results: The competency of synthesized nanocatalyst-Fe-Mo was observed to be good for the synthesis of β-enaminones derivatives under microwave irradiation and gave excellent yield (86-96%) of the product. The catalyst was recycled for more than five consecutive runs without significant loss in its activity. </P><P> Conclusion: In the present research article, synthesis of highly active, magnetically recyclable Fe- Mo nanocatalyst was obtained from easily available precursor. The MNP was stable under investigated conditions and effective in β-enaminones synthesis. The simple eco-friendly method, low catalyst loading, short transformation time, and reusability of the catalyst thoroughly follow the sustainable protocol.</P>

Unexpected Pyramid Texturization of n-Type Ge (100) via Electrochemical Etching: Bridging Surface Chemistry and Morphology

2018 ◽  
Vol 282 ◽  
pp. 94-98
Author(s):  
Graniel Harne A. Abrenica ◽  
Mikhail V. Lebedev ◽  
Hy Le ◽  
Andreas Hajduk ◽  
Mathias Fingerle ◽  
...  
Keyword(s):  
Surface Morphology ◽  
Surface Chemistry ◽  
Photoelectron Spectroscopy ◽  
Chemical Etching ◽  
Electrochemical Etching ◽  
Spectroscopic Techniques ◽  
X Ray ◽  
Etching Behavior ◽  
Effect Of Oxygen

We report on the (electro) chemical etching behavior, surface morphology and composition of n-type Ge (100) in acidic halide solutions using various analytical and spectroscopic techniques. The use of an integrated (electro) chemical etching chamber connected to X-ray photoelectron spectroscopy instrument to exclude the effect of oxygen from atmosphere is highlighted.

Removal of diazo dye Direct Red 23 from aqueous solution using zero-valent iron nanoparticles immobilized on multi-walled carbon nanotubes

2015 ◽  
Vol 71 (9) ◽  
pp. 1367-1374 ◽  
Author(s):  
Mahmoud Reza Sohrabi ◽  
Nafiseh Mansouriieh ◽  
Morteza Khosravi ◽  
Mohsen Zolghadr
Keyword(s):  
Carbon Nanotubes ◽  
Aqueous Solution ◽  
Zero Valent Iron ◽  
Mass Ratio ◽  
Solution Ph ◽  
Operational Conditions ◽  
Multi Walled Carbon Nanotubes ◽  
Diazo Dye ◽  
Zero Valent Iron Nanoparticles ◽  
Walled Carbon Nanotubes

The present study immobilized nanoscale zero-valent iron (nZVI) on multi-walled carbon nanotubes (MWCNTs) to enhance the reactivity of nZVI and prevent its aggregation. This novel composite (nZVI/MWCNT) was characterized by scanning electron microscopy and X-ray diffraction. The results showed that nZVI particles dispersed on the surface of the MWCNTs. The composite was used to remove the diazo dye Direct Red 23 from aqueous solution. The effects of nZVI to MWCNT mass ratio, nanocomposite content, solution pH, initial dye concentration and temperature were studied. The optimum nZVI/MWCNT mass ratio was 1:3. Batch experiments suggest that degradation efficiency decreased as the initial dye concentration increased and increased as the nanocomposite content increased, decreasing the pH from 8 to 4. The reaction followed a pseudo-first-order model under the operational conditions investigated in this study.

scholarly journals Studies on phenol removal from wastewater with CTAB-modified bentonite supported KMnO4

2013 ◽  
Vol 3 (3) ◽  
pp. 204-216 ◽  
Author(s):  
Jing Wang ◽  
Hongzhu Ma ◽  
Jie Yu ◽  
Shanshan Wang ◽  
Wenyan He ◽  
...  
Keyword(s):  
Removal Efficiency ◽  
Photoelectron Spectroscopy ◽  
Solid Phase ◽  
Phenol Degradation ◽  
Cod Removal ◽  
Phenol Removal ◽  
Solution Ph ◽  
Modified Bentonite ◽  
X Ray ◽  
Cod Removal Efficiency

Cetyltrimethylammonium bromide (CTAB) modified bentonite supported KMnO4 (KMnO4/CTAB-bent) was prepared by solid-phase grinding method, and applied to phenol removal from wastewater. Factors affecting efficiency, such as activated temperature, initial solution pH, KMnO4/CTAB-bent dosage, phenol initial concentration and reaction temperature on degradation were investigated. It was found that pH significantly affected the degradation and chemical oxygen demand (COD) removal efficiency. The results show that over 92% degradation and 60.58% COD removal efficiency can be obtained in 30 min. The surface properties and structure of KMnO4/CTAB-bent were measured by X-ray diffraction, X-ray photoelectron spectroscopy, Brunauer–Emmett–Teller, and Fourier transform infrared spectroscopy. However, it was demonstrated that the KMnO4/CTAB-bent was deactivated quickly during phenol degradation after the second cycle, indicating that the stability of KMnO4/CTAB-bent needs to be further improved.

Sign in / Sign up

Export Citation Format

Share Document