scholarly journals Constructed wetland using corncob charcoal substrate: pollutants removal and intensification

2017 ◽  
Vol 76 (6) ◽  
pp. 1300-1307 ◽  
Author(s):  
Mao Liu ◽  
Boyuan Li ◽  
Yingwen Xue ◽  
Hongyu Wang ◽  
Kai Yang
Keyword(s):  
Removal Efficiency ◽  
Constructed Wetlands ◽  
Oxygen Demand ◽  
Pollutant Removal ◽  
Vertical Flow ◽  
Pollutants Removal ◽  
Denitrification Process ◽  
Better Than ◽  
Potential Substrate ◽  
Stable Stage

To investigate the feasibility of using corncob charcoal substrate in constructed wetlands, four laboratory-scale vertical flow constructed wetlands (VFCWs) were built. Effluent pollutant (chemical oxygen demand (COD), NH4+-N, total phosphorus (TP)) concentrations during the experiment were determined to reveal pollutant removal mechanisms and efficiencies at different stages. In the stable stage, a VFCW using clay ceramisite substrate under aeration attained higher COD (95.1%), and NH4+-N (95.1%) removal efficiencies than a VFCW using corncob charcoal substrate (91.5% COD, 91.3% NH4+-N) under aeration, but lower TP removal efficiency (clay ceramisite 32.0% and corncob charcoal 40.0%). The VFCW with raw corncob substrate showed stronger COD emissions (maximum concentration 3,108 mg/L) than the corncob charcoal substrate (COD was lower than influent). The VFCW using corncob charcoal substrate performed much better than the VFCW using clay ceramisite substrate under aeration when the C/N ratio was low (C/N = 1.5, TN removal efficiency 36.89%, 4.1% respectively). These results suggest that corncob charcoal is a potential substrate in VFCWs under aeration with a unique self –supplying carbon source property in the denitrification process.

scholarly journals Modeling of Pollutants Removal in Subsurface Vertical Flow and Horizontal Flow Constructed Wetlands

Water ◽  
2019 ◽  
Vol 11 (1) ◽  
pp. 180 ◽  
Author(s):  
Wojciech Dąbrowski ◽  
Beata Karolinczak ◽  
Paweł Malinowski ◽  
Dariusz Boruszko
Keyword(s):  
Constructed Wetlands ◽  
Industrial Wastewater ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Pollutant Removal ◽  
Horizontal Flow ◽  
Vertical Flow ◽  
Treatment Efficiency ◽  
Reject Water ◽  
Pollutants Removal

Reject water is a by-product of every municipal and agro-industrial wastewater treatment plant (WWTP) applying sewage sludge stabilization. It is usually returned without pre-treatment to the biological part of WWTP, having a negative impact on the nitrogen removal process. The current models of pollutants removal in constructed wetlands concern municipal and industrial wastewater, whereas there is no such model for reject water. In the presented study, the results of treatment of reject water from dairy WWTP in subsurface vertical flow (SS VF) and subsurface horizontal flow (SS HF) beds were presented. During a one-year research period, SS VF bed reached 50.7% efficiency of TN removal and 73.8% of NH4+-N, while SS HF bed effectiveness was at 41.4% and 62.0%, respectively. In the case of BOD5 (biochemical oxygen demand), COD (chemical oxygen demand), NH4+-N, and TN (total nitrogen), the P-k-C* model was applied. Multi-model nonlinear segmented regression analysis was performed. Final mathematical models with estimates of parameters determining the treatment effectiveness were obtained. Treatment efficiency increased up to the specific temperature, then it was constant. The results obtained in this work suggest that it may be possible to describe pollutant removal behavior using simplified models. In the case of TP (total phosphorus) removal, distribution tests along with a t-test were performed. All models predict better treatment efficiency in SS VF bed, except for TP.

scholarly journals Treatment performances of French constructed wetlands: results from a database collected over the last 30 years

2015 ◽  
Vol 71 (9) ◽  
pp. 1333-1339 ◽  
Author(s):  
A. Morvannou ◽  
N. Forquet ◽  
S. Michel ◽  
S. Troesch ◽  
P. Molle
Keyword(s):  
Constructed Wetlands ◽  
Oxygen Demand ◽  
Pollutant Removal ◽  
Vertical Flow ◽  
Removal Rates ◽  
Waste Stabilization Ponds ◽  
Small Communities ◽  
Technical Department ◽  
In Series ◽  
High Chemical Oxygen Demand

Approximately 3,500 constructed wetlands (CWs) provide raw wastewater treatment in France for small communities (<5,000 people equivalent). Built during the past 30 years, most consist of two vertical flow constructed wetlands (VFCWs) in series (stages). Many configurations exist, with systems associated with horizontal flow filters or waste stabilization ponds, vertical flow with recirculation, partially saturated systems, etc. A database analyzed 10 years earlier on the classical French system summarized the global performances data. This paper provides a similar analysis of performance data from 415 full-scale two-stage VFCWs from an improved database expanded by monitoring data available from Irstea and the French technical department. Trends presented in the first study are confirmed, exhibiting high chemical oxygen demand (COD), total suspended solids (TSS) and total Kjeldahl nitrogen (TKN) removal rates (87%, 93% and 84%, respectively). Typical concentrations at the second-stage outlet are 74 mgCOD L−1, 17 mgTSS L−1 and 11 mgTKN L−1. Pollutant removal performances are summarized in relation to the loads applied at the first treatment stage. While COD and TSS removal rates remain stable over the range of applied loads, the spreading of TKN removal rates increases as applied loads increase.

scholarly journals Using one filter stage of unsaturated/saturated vertical flow filters for nitrogen removal and footprint reduction of constructed wetlands

2017 ◽  
Vol 76 (1) ◽  
pp. 124-133 ◽  
Author(s):  
Ania Morvannou ◽  
Stéphane Troesch ◽  
Dirk Esser ◽  
Nicolas Forquet ◽  
Alain Petitjean ◽  
...  
Keyword(s):  
Constructed Wetlands ◽  
Oxygen Demand ◽  
Pollutant Removal ◽  
Operating Conditions ◽  
Vertical Flow ◽  
Saturated Layer ◽  
Recirculation Rate ◽  
Total Filtration ◽  
Filtration Area ◽  
Stage System

French vertical flow constructed wetlands (VFCW) treating raw wastewater have been developed successfully over the last 30 years. Nevertheless, the two-stage VFCWs require a total filtration area of 2–2.5 m2/P.E. Therefore, implementing a one-stage system in which treatment performances reach standard requirements is of interest. Biho-Filter® is one of the solutions developed in France by Epur Nature. Biho-Filter® is a vertical flow system with an unsaturated layer at the top and a saturated layer at the bottom. The aim of this study was to assess this new configuration and to optimize its design and operating conditions. The hydraulic functioning and pollutant removal efficiency of three different Biho-Filter® plants commissioned between 2011 and 2012 were studied. Outlet concentrations of the most efficient Biho-Filter® configuration are 70 mg/L, 15 mg/L, 15 mg/L and 25 mg/L for chemical oxygen demand (COD), 5-day biological oxygen demand (BOD5), total suspended solids (TSS) and total Kjeldahl nitrogen (TKN), respectively. Up to 60% of total nitrogen is removed. Nitrification efficiency is mainly influenced by the height of the unsaturated zone and the recirculation rate. The optimum recirculation rate was found to be 100%. Denitrification in the saturated zone works at best with an influent COD/NO3-N ratio at the inflet of this zone larger than 2 and a hydraulic retention time longer than 0.75 days.

scholarly journals Effect of Ornamental Plants, Seasonality, and Filter Media Material in Fill-and-Drain Constructed Wetlands Treating Rural Community Wastewater

2019 ◽  
Vol 11 (8) ◽  
pp. 2350 ◽  
Author(s):  
Sergio A. Zamora-Castro ◽  
José Luis Marín-Muñiz ◽  
Luis Sandoval ◽  
Monserrat Vidal-Álvarez ◽  
Juan Manuel Carrión-Delgado
Keyword(s):  
Chemical Oxygen Demand ◽  
Removal Efficiency ◽  
Constructed Wetlands ◽  
Ornamental Plants ◽  
Oxygen Demand ◽  
Biomass Productivity ◽  
Pollutant Removal ◽  
Filter Media ◽  
Control Units ◽  
Phosphorous Compounds

The effects of Canna indica (P1), Pontederia sagittata (P2), and Spathiphyllum wallisii (P3) growing in different filter media materials (12 using porous river rock and 12 using tepezyl) on the seasonal removal of pollutants of wastewater using fill-and-drain constructed wetlands (FD-CWs) were investigated during 12 months. Three units of every media were planted with one plant of P1, P2, and P3, and three were kept unplanted. C. indica was the plant with higher growth than the other species, in both filter media. The species with more flower production were: C. indica > P. sagittate > S. wallisii. Reflecting similarly in the biomass of the plants, C. indica and P. sagittata showed more quantity of aerial and below ground biomass productivity than S. wallisii. With respect to the removal efficiency, both porous media were efficient in terms of pollutant removal performance (p > 0.05). However, removal efficiency showed a dependence on ornamental plants. The higher removal of chemical oxygen demand (COD), biochemical oxygen demand (BOD5), total kjeldahl nitrogen (TKN), nitrates (NO3−-N), ammonium (NH4+-N), and phosphates (PO4−3-P) oscillated between 81% to 83%, 80% to 84%, 61% to 69%, 61% to 68%, 65% to 71%, 62% to 68%, and 66% to 69%, respectively, in P1 and P2, removals 15% to 30% higher than P3. The removal in planted microcosms was significantly higher than the unplanted control units (p = 0.023). Nitrogen and phosphorous compounds were highly removed (60%–80%) because in typical CWs, such pollutant removals are usually smaller, indicating the importance of FD-CWs on wastewater treatments using porous river rock and tepezyl as porous filter media. (BOD5), chemical oxygen demand (COD), (NO3−-N), (NH4+-N), (TKN), and (PO4−3-P).

scholarly journals Post-treatment of tannery wastewater using pilot scale horizontal subsurface flow constructed wetlands (polishing)

2017 ◽  
Vol 77 (4) ◽  
pp. 988-998 ◽  
Author(s):  
Tadesse Alemu ◽  
Andualem Mekonnen ◽  
Seyoum Leta
Keyword(s):  
Removal Efficiency ◽  
Batch Reactor ◽  
Subsurface Flow ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Surface Flow ◽  
Tannery Wastewater ◽  
Treated Effluent ◽  
Horizontal Subsurface Flow ◽  
Pollutants Removal

Abstract In the present study, a pilot scale horizontal subsurface flow constructed wetland (CW) system planted with Phragmites karka; longitudinal profile was studied. The wetland was fed with tannery wastewater, pretreated in a two-stage anaerobic digester followed by a sequence batch reactor. Samples from each CW were taken and analyzed using standard methods. The removal efficiency of the CW system in terms of biological oxygen demand (BOD), chemical oxygen demand (COD), Cr and total coliforms were 91.3%, 90%, 97.3% and 99%, respectively. The removal efficiency for TN, NO3− and NH4+-N were 77.7%, 66.3% and 67.7%, respectively. Similarly, the removal efficiency of SO42−, S2− and total suspended solids (TSS) were 71.8%, 88.7% and 81.2%, respectively. The concentration of COD, BOD, TN, NO3−N, NH4+-N, SO42 and S2− in the final treated effluent were 113.2 ± 52, 56 ± 18, 49.3 ± 13, 22.75 ± 20, 17.1 ± 6.75, 88 ± 120 and 0.4 ± 0.44 mg/L, respectively. Pollutants removal was decreased in the first 12 m and increased along the CW cells. P. karka development in the first cell of CW was poor, small in size and experiencing chlorosis, but clogging was higher in this area due to high organic matter settling, causing a partial surface flow. The performance of the pilot CW as a tertiary treatment showed that the effluent meets the permissible discharge standards.

Biogeochemical indicators to evaluate pollutant removal efficiency in constructed wetlands

1997 ◽  
Vol 35 (5) ◽  
pp. 1-10 ◽  
Author(s):  
K. R. Reddy ◽  
E. M. D'Angelo
Keyword(s):  
Microbial Biomass ◽  
Removal Efficiency ◽  
Nitrate Removal ◽  
Oxygen Demand ◽  
Acid Soils ◽  
Pollutant Removal ◽  
Alkaline Soils ◽  
Organic C ◽  
Wetland Treatment ◽  
Biogeochemical Indicators

Wetlands support several aerobic and anaerobic biogeochemical processes that regulate removal/retention of pollutants, which has encouraged the intentional use of wetlands for pollutant abatement. The purpose of this paper is to present a brief review of key processes regulating pollutant removal and identify potential indicators that can be measured to evaluate treatment efficiency. Carbon and toxic organic compound removal efficiency can be determined by measuring soil or water oxygen demand, microbial biomass, soil Eh and pH. Similarly, nitrate removal can be predicted by dissolved organic C and microbial biomass. Phosphorus retention can be described by the availability of reactive Fe and Al in acid soils and Ca and Mg in alkaline soils. Relationships between soil processes and indicators are useful tools to transfer mechanistic information between diverse types of wetland treatment systems.

scholarly journals Effects of selection and compiling strategy of substrates in column-type vertical-flow constructed wetlands on the treatment of synthetic landfill leachate containing bisphenol A

2021 ◽  
Author(s):  
Rajani Ghaju Shrestha ◽  
Daisuke Inoue ◽  
Michihiko Ike
Keyword(s):  
Activated Carbon ◽  
Bisphenol A ◽  
Landfill Leachate ◽  
Low Cost ◽  
Oxygen Demand ◽  
Ammonium Nitrogen ◽  
Pollutant Removal ◽  
Vertical Flow ◽  
Batch Mode ◽  
Synthetic Leachate

Abstract A constructed wetland (CW) is a low-cost, eco-friendly, easy-to-maintain, and widely applicable technology for treating various pollutants in the waste landfill leachate. This study determined the effects of the selection and compiling strategy of substrates used in CWs on the treatment performance of a synthetic leachate containing bisphenol A (BPA) as a representative recalcitrant pollutant. We operated five types of lab-scale vertical-flow CWs using only gravel (CW1), a sandwich of gravel with activated carbon (CW2) or brick crumbs (CW3), and two-stage hybrid CWs using gravel in one column and activated carbon (CW4) or brick crumbs (CW5) in another to treat synthetic leachate containing BPA in a 7-d sequential batch mode for 5 weeks. CWs using activated carbon (CW2 and CW4) effectively removed ammonium nitrogen (NH4-N) (99–100%), chemical oxygen demand (COD) (93–100%), and BPA (100%), indicating that the high adsorption capacity of activated carbon was the main mechanism involved in their removal. CW5 also exhibited higher pollutant removal efficiencies (NH4-N: 94–99%, COD: 89–98%, BPA: 89–100%) than single-column CWs (CW1 and CW3) (NH4-N: 76–100%, COD: 84–100%, BPA: 51–100%). This indicates the importance of the compiling strategy along with the selection of an appropriate substrate to improve the pollutant removal capability of CWs.

scholarly journals Effects of salinity on the treatment of synthetic petroleum-industry wastewater in pilot vertical flow constructed wetlands under simulated hot arid climatic conditions

2020 ◽  
Vol 28 (2) ◽  
pp. 2172-2181
Author(s):  
Thomas V. Wagner ◽  
Fatma Al-Manji ◽  
Jie Xue ◽  
Koen Wetser ◽  
Vinnie de Wilde ◽  
...  
Keyword(s):  
Benzoic Acid ◽  
Removal Efficiency ◽  
Constructed Wetlands ◽  
Membrane Fouling ◽  
Plant Defence ◽  
Petroleum Industry ◽  
Vertical Flow ◽  
Treated Effluent ◽  
The Impact ◽  
Industry Wastewater

AbstractPetroleum-industry wastewater (PI-WW) is a potential source of water that can be reused in areas suffering from water stress. This water contains various fractions that need to be removed before reuse, such as light hydrocarbons, heavy metals and conditioning chemicals. Constructed wetlands (CWs) can remove these fractions, but the range of PI-WW salinities that can be treated in CWs and the influence of an increasing salinity on the CW removal efficiency for abovementioned fractions is unknown. Therefore, the impact of an increasing salinity on the removal of conditioning chemicals benzotriazole, aromatic hydrocarbon benzoic acid, and heavy metal zinc in lab-scale unplanted and Phragmites australis and Typha latifolia planted vertical-flow CWs was tested in the present study. P. australis was less sensitive than T. latifolia to increasing salinities and survived with a NaCl concentration of 12 g/L. The decay of T. latifolia was accompanied by a decrease in the removal efficiency for benzotriazole and benzoic acid, indicating that living vegetation enhanced the removal of these chemicals. Increased salinities resulted in the leaching of zinc from the planted CWs, probably as a result of active plant defence mechanisms against salt shocks that solubilized zinc. Plant growth also resulted in substantial evapotranspiration, leading to an increased salinity of the CW treated effluent. A too high salinity limits the reuse of the CW treated water. Therefore, CW treatment should be followed by desalination technologies to obtain salinities suitable for reuse. In this technology train, CWs enhance the efficiency of physicochemical desalination technologies by removing organics that induce membrane fouling. Hence, P. australis planted CWs are a suitable option for the treatment of water with a salinity below 12 g/L before further treatment or direct reuse in water scarce areas worldwide, where CWs may also boost the local biodiversity.

Nutrient removal efficiency and resource economics of vertical flow and horizontal flow constructed wetlands

2001 ◽  
Vol 18 (2) ◽  
pp. 157-171 ◽  
Author(s):  
Volker Luederitz ◽  
Elke Eckert ◽  
Martina Lange-Weber ◽  
Andreas Lange ◽  
Richard M Gersberg
Keyword(s):  
Removal Efficiency ◽  
Constructed Wetlands ◽  
Nutrient Removal ◽  
Resource Economics ◽  
Horizontal Flow ◽  
Vertical Flow ◽  
Nutrient Removal Efficiency
Sign in / Sign up

Export Citation Format

Share Document