scholarly journals Simultaneous adsorption and reduction of hexavalent chromium on biochar-supported nanoscale zero-valent iron (nZVI) in aqueous solution

2020 ◽  
Vol 82 (7) ◽  
pp. 1339-1349
Author(s):  
Fengfeng Ma ◽  
Bakunzibake Philippe ◽  
Baowei Zhao ◽  
Jingru Diao ◽  
Jian Li
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Photoelectron Spectroscopy ◽  
Zero Valent Iron ◽  
X Ray Diffraction ◽  
Experimental Conditions ◽  
X Ray ◽  
Transmission Electron ◽  
Nanoscale Zero Valent Iron ◽  
Pseudo Second Order

Abstract Flax straw biochar (FSBC)-supported nanoscale zero-valent iron (nZVI) composite (nZVI-FSBC) combining the advantages of nZVI and biochar was synthesized and tested for Cr(VI) removal efficiency from aqueous solution. Surface morphology and structure of FSBC and nZVI-FSBC were characterized by scanning electron microscopy, transmission electron microscopy, thermogravimetric analysis, X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), and Brunauer–Emmett–Teller techniques, which help to clarify the mechanism of Cr(VI) removal from aqueous solution. The adsorption of Cr(VI) onto FSBC and nZVI-FSBC was best described by the pseudo-second-order and the Sips model. Compared with FSBC, nZVI-FSBC remarkably improved the performance in removing Cr(VI) under identical experimental conditions. Due to the collaborative effect of adsorption and reduction of nZVI-FSBC, the adsorption capacity of nZVI-FSBC for Cr(VI) is up to 186.99 mg/g. The results obtained by XPS, XRD, and FTIR confirmed that adsorption and reduction dominated the processes of Cr(VI) removal by nZVI-FSBC. As a supporter, FSBC not only improved the dispersion of nZVI, but also undertook the adsorption task of Cr(VI) removal. The surface oxygen-containing functional groups of nZVI-FSBC mainly participated in the adsorption part, and the nZVI promoted the Cr(VI) removal through the redox reactions. These observations indicated that the nZVI-FSBC can be considered as potential adsorbents to remove Cr(VI) for environment remediation.

scholarly journals Biomass-Derived Activated Carbon as a Catalyst for the Effective Degradation of Rhodamine B dye

Processes ◽  
2020 ◽  
Vol 8 (8) ◽  
pp. 926
Author(s):  
Shamim Ahmed Hira ◽  
Mohammad Yusuf ◽  
Dicky Annas ◽  
Hu Shi Hui ◽  
Kang Hyun Park
Keyword(s):  
Electron Microscopy ◽  
Activated Carbon ◽  
Rhodamine B ◽  
Photoelectron Spectroscopy ◽  
High Specific Surface Area ◽  
High Porosity ◽  
X Ray Diffraction ◽  
Experimental Conditions ◽  
X Ray ◽  
Transmission Electron

Activated carbon (AC) was fabricated from carrot waste using ZnCl2 as the activating agent and calcined at 700 °C for 2 h in a tube furnace. The as-synthesized AC was characterized using Fourier-transform infrared spectroscopy, X-ray diffraction analysis, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, and Brunauer–Emmett–Teller analysis; the results revealed that it exhibited a high specific surface area and high porosity. Moreover, this material displayed superior catalytic activity for the degradation of toxic Rhodamine B (RhB) dye. Rate constant for the degradation of RhB was ascertained at different experimental conditions. Lastly, we used the Arrhenius equation and determined that the activation energy for the decomposition of RhB using AC was approximately 35.9 kJ mol−1, which was very low. Hopefully it will create a great platform for the degradation of other toxic dye in near future.

Mechanism of Cu2+ Ions Removal from Aqueous Solution with PBTCA Modified Fe0 Nanoparticles

2014 ◽  
Vol 522-524 ◽  
pp. 454-457
Author(s):  
Jing Wei Feng ◽  
Ying Xia Xu
Keyword(s):  
Aqueous Solution ◽  
Iron Oxide ◽  
Photoelectron Spectroscopy ◽  
Aqueous Media ◽  
Zero Valent Iron ◽  
Borohydride Reduction ◽  
Experimental Conditions ◽  
Redox Mechanism ◽  
X Ray ◽  
Nanoscale Zero Valent Iron

Applications of PBTCA modified nanoscale zero valent iron (P-Fe0) prepared by borohydride reduction for removal of Cu2+ions from aqueous solution are investigated under a variety of experimental conditions. According to X-ray photoelectron spectroscopy (XPS) results, Cu2+ions were removed primarily via a redox mechanism that resulted in the formation of Cu0and Cu2O. The contact of P-Fe0with aqueous media caused extensive formation of iron oxide.

scholarly journals The Synthesis of PbS NPs and Biosorption of Pb(II) by Shinella Zoogloeoides PQ7 in Aqueous Conditions

Water ◽  
2020 ◽  
Vol 12 (7) ◽  
pp. 2065
Author(s):  
Wei Zhang ◽  
Yili Huang
Keyword(s):  
Electron Microscopy ◽  
Heavy Metal ◽  
Photoelectron Spectroscopy ◽  
Freundlich Isotherm ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Pseudo Second Order ◽  
Biomass Dosage ◽  
Aqueous Conditions

Increasing heavy metal pollution in water continues to endanger human health. The genus Shinella has potential for heavy metal bioremediation but has rarely been studied. In this study, we report that Shinella zoogloeoides PQ7 turns black in the presence of lead ions. Transmission electron microscopy (TEM), Scanning electron microscopy–energy dispersive X-ray spectroscopy (SEM–EDS), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) indicated that PbS nanoparticles (NPs) were synthesized by PQ7. Moreover, PQ7 was used as a biosorbent to remove Pb(II) from aqueous solutions. Biosorption performance was evaluated in terms of contact time, pH, biomass dosage and initial Pb(II) concentration. The equilibrium and kinetic data were consistent with the Freundlich isotherm model (R2 = 0.986) and pseudo-second-order model (R2 = 0.977), respectively. The maximum (qmax) Pb(II) adsorption reached 222.22 mg/g, which was higher than that of other bacteria reported in previous literature. SEM–EDS, XRD and Fourier transform infrared (FTIR) analyses also confirmed the adsorption of Pb(II) by the PQ7 cells. In conclusion, PQ7 is a promising strain in removing and recovering Pb(II) from wastewater.

scholarly journals Synthesis of Ce1−xPdxO2−δ Solid Solution in Molten Nitrate

Catalysts ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 640
Author(s):  
Hideaki Sasaki ◽  
Keisuke Sakamoto ◽  
Masami Mori ◽  
Tatsuaki Sakamoto
Keyword(s):  
Electron Microscopy ◽  
Solid Solution ◽  
Solid Solutions ◽  
Photoelectron Spectroscopy ◽  
Synthesis Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Co Precipitation ◽  
Ionic States

CeO2-based solid solutions in which Pd partially substitutes for Ce attract considerable attention, owing to their high catalytic performances. In this study, the solid solution (Ce1−xPdxO2−δ) with a high Pd content (x ~ 0.2) was synthesized through co-precipitation under oxidative conditions using molten nitrate, and its structure and thermal decomposition were examined. The characteristics of the solid solution, such as the change in a lattice constant, inhibition of sintering, and ionic states, were examined using X-ray diffraction (XRD), scanning electron microscopy–energy-dispersive X-ray spectroscopy (SEM−EDS), transmission electron microscopy (TEM)−EDS, and X-ray photoelectron spectroscopy (XPS). The synthesis method proposed in this study appears suitable for the easy preparation of CeO2 solid solutions with a high Pd content.

scholarly journals Aluminum Nitride-Silicon Carbide Alloy Crystals Grown on SiC Substrates by Sublimation

2005 ◽  
Vol 10 ◽  
Author(s):  
Z. Gu ◽  
L. Du ◽  
J.H. Edgar ◽  
E.A. Payzant ◽  
L. Walker ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
X Ray Diffraction ◽  
Original Source ◽  
X Ray ◽  
Alloy Crystal ◽  
Transmission Electron ◽  
Crystal Substrate ◽  
Vapor Distribution ◽  
Uniform Composition

AlN-SiC alloy crystals, with a thickness greater than 500 µm, were grown on 4H- and 6H-SiC substrates from a mixture of AlN and SiC powders by the sublimation-recondensation method at 1860-1990 °C. On-axis SiC substrates produced a rough surface covered with hexagonal grains, while 6H- and 4H- off-axis SiC substrates with different miscut angles (8° or 3.68°) formed a relatively smooth surface with terraces and steps. The substrate misorientation ensured that the AlN-SiC alloy crystals grew two dimensionally as identified by scanning electron microscopy (SEM). X-ray diffraction (XRD) and transmission electron microscopy (TEM) confirmed that the AlN-SiC alloys had the wurtzite structure. Electron probe microanalysis (EPMA) and x-ray photoelectron spectroscopy (XPS) demonstrated that the resultant alloy crystals had non-stoichiometric ratios of Al:N and Si:C and a uniform composition throughout the alloy crystal from the interface to the surface. The composition ratio of Al:Si of the alloy crystals changed with the growth temperature, and differed from the original source composition, which was consistent with the results predicted by thermodynamic calculation of the solid-vapor distribution of each element. XPS detected the bonding between Si-C, Si-N, Si-O for the Si 2p spectra. The dislocation density decreased with the growth, which was lower than 106 cm−2 at the alloy surface, more than two orders of magnitude lower compared to regions close to the crystal/substrate interface, as determined by TEM.

scholarly journals Synthesis of Three-Dimensional Fe3O4/Graphene Aerogels for the Removal of Arsenic Ions from Water

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Yan Ye ◽  
Da Yin ◽  
Bin Wang ◽  
Qingwen Zhang
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
3D Structure ◽  
Three Dimensional ◽  
X Ray Diffraction ◽  
X Ray ◽  
Graphene Aerogels ◽  
Transmission Electron ◽  
Potential Applications ◽  
Removal Of Arsenic

We report the synthesis of three-dimensional Fe3O4/graphene aerogels (GAs) and their application for the removal of arsenic (As) ions from water. The morphology and properties of Fe3O4/GAs have been characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and superconducting quantum inference device. The 3D nanostructure shows that iron oxide nanoparticles are decorated on graphene with an interconnected network structure. It is found that Fe3O4/GAs own a capacity of As(V) ions adsorption up to 40.048 mg/g due to their remarkable 3D structure and existence of magnetic Fe3O4nanoparticles for separation. The adsorption isotherm matches well with the Langmuir model and kinetic analysis suggests that the adsorption process is pseudo-second-ordered. In addition to the excellent adsorption capability, Fe3O4/GAs can be easily and effectively separated from water, indicating potential applications in water treatment.

scholarly journals Photocatalytic Degradation of Tetracycline in Aqueous Solution Using Copper Sulfide Nanoparticles

Catalysts ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1238
Author(s):  
Murendeni P. Ravele ◽  
Opeyemi A. Oyewo ◽  
Sam Ramaila ◽  
Lydia Mavuru ◽  
Damian C. Onwudiwe
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Copper Sulfide ◽  
Degradation Rate ◽  
Light Exposure ◽  
Reaction System ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Pure Phase

In this paper, spherical-shaped pure phase djurleite (Cu31S16) and roxbyite (Cu7S4) nanoparticles were prepared by a solvothermal decomposition of copper(II) dithiocarbamate complex in dodecanthiol (DDT). The reaction temperature was used to control the phases of the samples, which were represented as Cu31S16 (120 °C), Cu31S16 (150 °C), Cu7S4 (220 °C), and Cu7S4 (250 °C) and were characterized by using X-ray diffraction (XRD), scanning and transmission electron microscopy (SEM and TEM), and absorption spectroscopy. The samples were used as photocatalysts for the degradation of tetracycline (TC) under visible light irradiation. The results of the study showed that Cu7S4 (250 °C) exhibited the best activity in the reaction system with the TC degradation rate of up to 99% within 120 min of light exposure, while the Cu31S16 (120 °C) system was only 46.5% at the same reaction condition. In general, roxbyite Cu7S4 (250 °C) could be considered as a potential catalyst for the degradation of TC in solution.

scholarly journals Microwave-assisted preparation of ZnS and ZnSe nanocrystals with different morphologies for photodegradation process of organic dyes

2019 ◽  
Author(s):  
Katarzyna Matras-Postolek ◽  
A. Zaba ◽  
S. Sovinska ◽  
D. Bogdal
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Organic Dyes ◽  
Zinc Sulphide ◽  
Conventional Heating ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Vis Spectroscopy

Zinc sulphide (ZnS) and zinc selenide (ZnSe) and manganese-doped and un-doped with different morphologies from 1D do 3D microflowers were successfully fabricated in only a few minutes by solvothermal reactions under microwave irradiation. In order to compare the effect of microwave heating on the properties of obtained  nanocrystals, additionally the synthesis under conventional heating was conducted additionally in similar conditions. The obtained nanocrystals were systematically characterized in terms of structural and optical properties using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), diffuse reflectance UV-Vis spectroscopy (DR UV-Vis), Fourier-transform infrared spectroscopy (FT-IR), photoluminescence spectroscopy (PL), X-ray photoelectron spectroscopy (XPS) and Brunauer-Emmett-Teller (BET) surface area analysis. The photocatalytic activity of ZnSe, ZnS, ZnS:Mn and ZnSe:Mn nanocrystals with different morphologies was evaluated by the degradation of methyl orange (MO) and Rhodamine 6G (R6G), respectively. The results show that Mn doped NCs samples had higher coefficient of degradation of organic dyes under ultraviolet irradiation (UV).

Synthesis and characterization of homogeneous lead-substituted tin oxide with the (110) face of rutile structure

2000 ◽  
Vol 15 (10) ◽  
pp. 2076-2079
Author(s):  
Chika Nozaki ◽  
Takashi Yamada ◽  
Kenji Tabata ◽  
Eiji Suzuki
Keyword(s):  
Electron Microscopy ◽  
Tin Oxide ◽  
Photoelectron Spectroscopy ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Rutile Structure ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

Synthesis of a rutile-type lead-substituted tin oxide with (110) face was investigated. The characterization was performed by x-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy dispersive x-ray spectroscopy, infrared spectroscopy, x-ray photoelectron spectroscopy, and Brunauer–Emmett–Teller surface area measurements. The homogeneous rutile-type lead-substituted tin oxide was obtained until 4.1 mol% of tin was substituted with lead. The surface of obtained oxide had a homogeneously lead-substituted (110) face.

A Facile Strategy to Fabricate Nanoscale Zero-Valent Iron Decorated Graphene Oxide Composite for Dechloridation of Trichloroacetic Acid in Water

2018 ◽  
Vol 18 (12) ◽  
pp. 8252-8257 ◽  
Author(s):  
Huixuan Zhang ◽  
Xinyi Zhang ◽  
Ruonan Guo ◽  
Qingfeng Cheng ◽  
Xiuwen Cheng
Keyword(s):  
Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Sewage Treatment ◽  
Reduction Process ◽  
Zero Valent Iron ◽  
Chlorinated Organic Compounds ◽  
X Ray ◽  
Transmission Electron ◽  
Nanoscale Zero Valent Iron ◽  
Adsorption Desorption

In this study, nanoscale zero-valent iron decorated graphene oxide (NZVI/GO) composite was fabricated through a reduction process in the presence of sodium borohydride (NaBH4) solution. Subsequently, physicochemical properties of the NZVI/GO composites were characterized by scanning electron microscope (SEM), transmission electron microscopy (TEM), N2 adsorption/desorption, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transformation infrared spectroscopy (FT-IR) and Raman spectra. Results indicated that Fe species existed in the form of Fe0, which uniformly dispersed on the surface of GO. Furthermore, the performance of NZVI/GO was evaluated by the degradation of tichloroacetic acid (TCAA). TCAA can be rapidly degraded by NZVI/GO. This paper provides a promising strategy to synthesize versatile catalyst which would be potentially applied in sewage treatment to degrade chlorinated organic compounds.

Sign in / Sign up

Export Citation Format

Share Document