Silymarin Spray-Dried Proliposomes: Preparation, Characterization and Cytotoxic Evaluation

2020 ◽  
Vol 10 (1) ◽  
pp. 14-23
Author(s):  
Ahmed Gardouh ◽  
Sherif Shaker ◽  
Zainab Z. Ali ◽  
Mamdouh Ghorab
Keyword(s):  
Particle Size ◽  
Physicochemical Properties ◽  
Spray Drying ◽  
Encapsulation Efficiency ◽  
In Vitro Release ◽  
Tween 80 ◽  
Cholesterol Concentration ◽  
Ethanol Injection ◽  
Vitro Release

Background: Most liposomes problems are due to stability and consistency. Proliposomes is one of the solutions to overcome the disadvantage of liposomes. They are available in dry powder form, it is easy to distribute, transfer, measure and store. Objective: The aim of the present study was to find a novel method of preparing Silymarin proliposomes and study the effect of cholesterol concentrations and surfactant types on the physicochemical properties of silymarin proliposomes and its in-vitro release. Methods: Silymarin proliposomes were prepared by combining two simple methods ethanol injection method for liposomes preparation followed by the spray drying method to get a dry powder. The physicochemical properties including particle size, TEM, SEM, FTIR, encapsulation efficiency and dissolution studies were studied. Results: The particle size of silymarin liposomes were below 552.36 ± 17.63 nm but after reconstitution of silymarin proliposomes, the particle size was in the micro range due to the influence of the spray drying process. Cholesterol concentration was ranged from 50 to 150 mg per formula. Increasing Cholesterol concentration caused a significant increase in liposomes particle size and reduction in encapsulation efficiency. Three non-ionic surfactants were used to prepare silymarin proliposomes Tween 80, Cremophor RH 40 and Poloxamer 407. Formula F1 prepared with Phosal® 53 MCT (300 mg), Tween 80 (50 mg), cholesterol (50 mg) and Silymarin (140 mg) showed the smallest particle size (2066 ± 164.87 nm) upon reconstitution in water, highest encapsulation efficiency (89.51 ± 0.43%), and fastest in vitro release compared to other formulas. Cytotoxicity of Silymarin, formula F1 and formula F1/blank was assessed using an MTT assay on MCF-7, HepG2 and HBF-4 cells. The cytotoxic effect of silymarin was enhanced by loading it on proliposomes. Conclusion: Silymarin was successfully formulated into proliposomes combining ethanol injection and spray drying methods. The cytotoxicity of silymarin was improved when loaded on proliposomes owing to the formula.

Optimization and Characterization of Aqueous Micellar Formulations for Ocular Delivery of an Antifungal Drug, Posaconazole

2020 ◽  
Vol 26 (14) ◽  
pp. 1543-1555 ◽  
Author(s):  
Meltem E. Durgun ◽  
Emine Kahraman ◽  
Sevgi Güngör ◽  
Yıldız Özsoy
Keyword(s):  
Particle Size ◽  
Zeta Potential ◽  
Size Distribution ◽  
Encapsulation Efficiency ◽  
Fungal Infections ◽  
In Vitro Release ◽  
Pluronic F127 ◽  
Glycol Succinate ◽  
Vitro Release

Background: Topical therapy is preferred for the management of ocular fungal infections due to its superiorities which include overcoming potential systemic side effects risk of drugs, and targeting of drugs to the site of disease. However, the optimization of effective ocular formulations has always been a major challenge due to restrictions of ocular barriers and physiological conditions. Posaconazole, an antifungal and highly lipophilic agent with broad-spectrum, has been used topically as off-label in the treatment of ocular fungal infections due to its highly lipophilic character. Micellar carriers have the potential to improve the solubility of lipophilic drugs and, overcome ocular barriers. Objective: In the current study, it was aimed optimization of posaconazole loaded micellar formulations to improve aqueous solubility of posaconazole and to characterize the formulations and to investigate the physical stability of these formulations at room temperature (25°C, 60% RH), and accelerated stability (40°C, 75% RH) conditions. Method: Micelles were prepared using a thin-film hydration method. Pre-formulation studies were firstly performed to optimize polymer/surfactant type and to determine their concentration in the formulations. Then, particle size, size distribution, and zeta potential of the micellar formulations were measured by ZetaSizer Nano-ZS. The drug encapsulation efficiency of the micelles was quantified by HPLC. The morphology of the micelles was depicted by AFM. The stability of optimized micelles was evaluated in terms of particle size, size distribution, zeta potential, drug amount and pH for 180 days. In vitro release studies were performed using Franz diffusion cells. Results: Pre-formulation studies indicated that single D-ɑ-tocopheryl polyethylene glycol succinate (TPGS), a combination of it and Pluronic F127/Pluronic F68 are capable of formation of posaconazole loaded micelles at specific concentrations. Optimized micelles with high encapsulation efficiency were less than 20 nm, approximately neutral, stable, and in aspherical shape. Additionally, in vitro release data showed that the release of posaconazole from the micelles was higher than that of suspension. Conclusion: The results revealed that the optimized micellar formulation of posaconazole offers a potential approach for topical ocular administration.

scholarly journals Application of Molecularly Structured Ben Oil in Gentamicin Entrapped Lipospheres

2019 ◽  
pp. 262-270 ◽  
Author(s):  
Salome A. Chime ◽  
Ikechukwu V. Onyishi ◽  
Ifeoma O. Eze
Keyword(s):  
Particle Size ◽  
Encapsulation Efficiency ◽  
Moringa Oleifera ◽  
Extended Release ◽  
In Vitro Release ◽  
Antimicrobial Studies ◽  
Microbial Inhibition ◽  
Vitro Release ◽  
Moringa Oleifera Seed

Objective: To formulate extended release gentamicin-entrapped lipospheres using natural lipids from Irvingia wombolu (IWF) and Moringa oleifera seed (MO) popularly known as Ben oil. Methods: Different lipid combinations including IWF and Phospholipon 90H (P90H) and IWF and MO were employed in the formulation of lipospheres. The formulations were analysed for particle size, encapsulation efficiency (EE), pH stability and antimicrobial studies amongst other tests. Also the in vitro release properties were studied in Phosphate buffer pH 7.2. Results: High EE of up to 90 % were obtained for the various LM combinations. The pH was stable over 30 days and the formulations showed about 93 % release of gentamicin at 12 h. Lipospheres formulated with MO matrices showed synergism in the microbial inhibition than other formulations. Conclusion: Natural lipids from Irvingia wombolu and Moringa oleifera seed could be used in formulating oral extended release gentamicin lipospheres.

scholarly journals Effect of Lipids on Physicochemical Properties of Letrozole Loaded Solid Lipid Nanoparticles

2016 ◽  
Vol 8 (05) ◽  
Author(s):  
Archana Nerella ◽  
Basava Dontamsetti ◽  
Aruna Mantena
Keyword(s):  
Particle Size ◽  
Physicochemical Properties ◽  
Solid Lipid Nanoparticles ◽  
In Vitro Release ◽  
Physicochemical Characteristics ◽  
Lipid Nanoparticles ◽  
Solid Lipid ◽  
Stabilizer Concentration ◽  
Vitro Release

The objective of the current investigation was to prepare solid lipid nanoparticles (SLNs) from different lipids and to study the effect of lipids on physicochemical characteristics of letrozole loaded SLN. In order to prepare small, stable, uniform and high Letrozole loaded SLNs, many factors such as lipid and stabilizer concentration and preparation parameters can be considered. Out of these, we have selected solid lipid as lipid matrix to investigate an effect on SLNs. SLNs were prepared using different lipids by modified hot sonication method. The effect of different lipids and stabilizers on physicochemical characteristics of Letrozole loaded SLNs were investigated. Letrozole loaded SLNs showed different physicochemical properties and release profiles according to used solid lipid. In case of particle size, SLN1 showed biggest particle size (532.5 ± 26.4nm) and highest encapsulation efficiency (81.37 ± 6.72%) and, SLN4 showed highest cumulative drug percentage (89.4 ± 1.8%, 24 h) release. These results suggest that lipids type affect physicochemical properties and release profile of SLN. The choice of lipid and stabilizer played important role on the physicochemical characteristics and in vitro release of Letrozole loaded SLNs.

scholarly journals Formulation development and evaluation of Glibenclamide loaded Eudragit RLPO microparticles

2013 ◽  
Vol 2 (12) ◽  
pp. 196-201 ◽  
Author(s):  
Balagani Pavan Kumar ◽  
Irisappan Sarath Chandiran ◽  
Korlakunta Narasimha Jayaveera
Keyword(s):  
Particle Size ◽  
Encapsulation Efficiency ◽  
In Vitro Release ◽  
Solvent Evaporation ◽  
Solvent Evaporation Method ◽  
Evaporation Method ◽  
Release Studies ◽  
Vitro Release ◽  
Eudragit Rlpo

The objective of the present investigation was to formulate and evaluate microencapsulated Glibenclamide produced by the emulsion – solvent evaporation method. Microparticles were prepared using Eudragit RLPO by emulsion solvent evaporation method and characterized for their micromeritic properties, encapsulation efficiency, particle size, drug loading, FTIR, DSC, SEM analysis. In vitro release studies were performed in phosphate buffer (pH 7.4). Stability studies were conducted as per ICH guidelines. The resulting microparticles obtained by solvent evaporation method were free flowing in nature. The mean particle size of microparticles ranges from 134.49 – 179.72 µm and encapsulation efficiency ranges from 92.30-98.32%. The infrared spectra and differential scanning calorimetry thermographs confirmed the stable character of Glibenclamide in the drug-loaded microparticles. Scanning electron microscopy revealed that the microparticles were spherical in nature. In vitro release studies revealed that the drug release was sustained up to 12 hrs. The release kinetics of Glibenclamide from optimized formulation followed zero-order and peppas mechanism. The mechanism of drug release from the microparticles was found to be non-Fickian type. Eudragit RLPO microparticles containing Glibenclamide could be prepared successfully by using an emulsion solvent evaporation technique, which will not only sustain the release of drug but also manage complicacy of the diabetes in a better manner.DOI: http://dx.doi.org/10.3329/icpj.v2i12.17016 International Current Pharmaceutical Journal, November 2013, 2(12): 196-201

scholarly journals Formulation and Evaluation of Nanoemulsion using Tazarotene and Curcumin

2021 ◽  
pp. 807-815
Author(s):  
Parmita Phaugat ◽  
Suchitra Nishal ◽  
Aparna Khansili
Keyword(s):  
Particle Size ◽  
Zeta Potential ◽  
Ternary Phase Diagram ◽  
In Vitro Release ◽  
Tween 80 ◽  
High Energy ◽  
Oral Route ◽  
Topical Formulation ◽  
Vitro Release

Aims: To formulate and evaluate nanoemulsion of Tazarotene and Curcumin Study Design: Ultrsonication Methods. Place and Duration of Study, Sample: Swami Dayanand Postgraduate Institute of Pharmaceuticals Sciences, University of Health Sciences, Rohtak; 2020-2021 Methodology: Oleic acid, tween 80, and propylene glycol were selected as oil, surfactant, and co-surfactant, respectively. The ratio of oil: surfactant: co-surfactant was selected based on a ternary phase diagram using the aqueous titration method. The selected ratio was employed to develop eight formulations of Tazarotene-curcumin by ultra-sonication. The formulations (F1-F8) were characterized using several physicochemical methods like pH, viscosity, particle size distribution, zeta potential, drug content, and in vitro release. The optimized formulation was selected based on the results of characterization. Results: The formulations (F1-F8) were formulated by using the ultrasonication (high energy) method. The optimized formulation possessed particle size 121, 0.382 PDI, and -20.1 zeta potential. The in vitro release of F6 was found to be 90.9 ± 3.1 at 24 hours. It also passed the thermodynamic stability tests. Conclusion: The current investigations conclude that Tazarotene-curcumin nanoemulsion can be used as an alternative to the oral route of tazarotene and is also useful in reducing the adverse effects associated with oral. The physicochemical evaluation of the formulation showed that the nanoemulsion had the necessary properties for a topical formulation.

Formulation and Evaluation of Mefloquine Hydrochloride Nanoparticles

2014 ◽  
Vol 7 (1) ◽  
pp. 2377-2386
Author(s):  
Dilip Kumar Gupta ◽  
B K Razdan ◽  
Meenakshi Bajpai
Keyword(s):  
Particle Size ◽  
Sustained Release ◽  
In Vitro Release ◽  
Entrapment Efficiency ◽  
Taste Masking ◽  
Diffusion Method ◽  
Drug Entrapment Efficiency ◽  
Resistant Strains ◽  
Vitro Release

The present study deals with the formulation and evaluation of mefloquine hydrochloride nanoparticles. Mefloquine is a blood schizonticidal quinoline compound, which is indicated for the treatment of mild-to-moderate acute malarial infections caused by mefloquine-susceptible multi-resistant strains of P. falciparum and P. vivax. The purpose of the present work is to minimize the dosing frequency, taste masking toxicity and to improve the therapeutic efficacy by formulating mefloquine HCl nanoparticles. Mefloquine nanoparticles were formulated by emulsion diffusion method using polymer poly(ε-caprolactone) with six different formulations. Nanoparticles were characterized by determining its particle size, polydispersity index, drug entrapment efficiency, drug content, particle morphological character and drug release. The particle size ranged between 100 nm to 240 nm. Drug entrapment efficacy was >95%. The in-vitro release of nanoparticles were carried out which exhibited a sustained release of mefloquine HCl from nanoparticles up to 24 hrs. The results showed that nanoparticles can be a promising drug delivery system for sustained release of mefloquine HCl.

Preparation, Characterization and In-vitro release of Piroxicam-loaded Solid Lipid Nanoparticles

2010 ◽  
Vol 3 (3) ◽  
pp. 1136-1146
Author(s):  
V K Verma ◽  
Ram A
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Solid Lipid Nanoparticles ◽  
In Vitro Release ◽  
Entrapment Efficiency ◽  
Lipid Nanoparticles ◽  
Diffusion Method ◽  
Solid Lipid ◽  
Vitro Release

 Solid lipid nanoparticles (SLNs) of piroxicam where produced by solvent emulsification diffusion method in a solvent saturated system. The SLNs where composed of tripamitin lipid, polyvinyl alcohol (PVAL) stabilizer, and solvent ethyl acetate. All the formulation were subjected to particle size analysis, zeta potential, drug entrapment efficiency, percent drug loading determination and in-vitro release studies. The SLNs formed were nano-size range with maximum entrapment efficiency. Formulation with 435nm in particle size and 85% drug entrapment was subjected to scanning electron microscopy (SEM) and transmission electron microscopy (TEM) for surface morphology, differential scanning calorimetry (DSC) for thermal analysis and short term stability studies. SEM and TEM confirm that the SLNs are nanometric size and circular in shape. The drug release behavior from SLNs suspension exhibited biphasic pattern with an initial burst and prolong release over 24 h. 

scholarly journals Development of nitazoxanide-loaded colon-targeted formulation for intestinal parasitic infections: centre composite design-based optimization and characterization

2020 ◽  
Vol 6 (1) ◽  
Author(s):  
Charu Bharti ◽  
Upendra Nagaich ◽  
Jaya Pandey ◽  
Suman Jain ◽  
Neha Jain
Keyword(s):  
Particle Size ◽  
Desirability Function ◽  
In Vitro Release ◽  
Entrapment Efficiency ◽  
In Vitro Drug Release ◽  
Release Studies ◽  
Percentage Yield ◽  
Vitro Release ◽  
Selection Of

Abstract Background The current investigation is focused on the development and characterization of Eudragit S100 coated nitazoxanide-loaded microbeads as colon-targeted system utilizing central composite design (CCD) and desirability function. The study initiated with the selection of a BCS class II drug nitazoxanide and its preformulation screening with excipients, selection of polymer and identification of concentration for CCD, selection of optimized formulation based on desirability function, and in vitro release studies in simulated gastric and colonic media and stability studies. A two-factor, three-level CCD was employed with two independent variables, i.e. X1 (chitosan % w/v) and X2 (sodium tripolyphosphate % w/v), and three dependent variables, i.e. Y1 (particle size in micrometres), Y2 (percentage yield) and Y3 (percent entrapment efficiency), were chosen. Additionally, surface morphology, mucoadhesion and in vitro drug release studies were also conducted. Result Chitosan concentration showing maximum entrapment and optimum particle size was selected to formulate chitosan beads. The polynomial equation and model graphs obtained from the Design-Expert were utilized to examine the effect of independent variables on responses. The effect of formulation composition was found to be significant (p ˂ 0.05). Based on the desirability function, the optimized formulation was found to have 910.14 μm ± 1.03 particle size, 91.84% ± 0.64 percentage yield and 84.75% ± 0.38 entrapment efficiency with a desirability of 0.961. Furthermore, the formulations were characterized for in vitro drug release in simulated colonic media (2% rat caecal content) and have shown a sustained release of ∼ 92% up to 24 h as compared to in vitro release in simulated gastric fluid. Conclusion The possibility of formulation in enhancing percentage yield and entrapment efficiency of nitazoxanide and the utilization of CCD helps to effectively integrate nitazoxanide microbeads into a potential pharmaceutical dosage form for sustained release.

scholarly journals pH-Responsive Liposomes of Dioleoyl Phosphatidylethanolamine and Cholesteryl Hemisuccinate for the Enhanced Anticancer Efficacy of Cisplatin

Pharmaceutics ◽  
2022 ◽  
Vol 14 (1) ◽  
pp. 129
Author(s):  
Hassan Shah ◽  
Asadullah Madni ◽  
Muhammad Muzamil Khan ◽  
Fiaz-ud-Din Ahmad ◽  
Nasrullah Jan ◽  
...  
Keyword(s):  
Particle Size ◽  
Zeta Potential ◽  
Release Rate ◽  
In Vitro Release ◽  
Chemotherapeutic Agents ◽  
Ph Responsive ◽  
Scanning Calorimetry ◽  
Cholesteryl Hemisuccinate ◽  
Vitro Release

The current study aimed to develop pH-responsive cisplatin-loaded liposomes (CDDP@PLs) via the thin film hydration method. Formulations with varied ratios of dioleoyl phosphatidylethanolamine (DOPE) to cholesteryl hemisuccinate (CHEMS) were investigated to obtain the optimal particle size, zeta potential, entrapment efficiency, in vitro release profile, and stability. The particle size of the CDDP@PLs was in the range of 153.2 ± 3.08–206.4 ± 2.26 nm, zeta potential was −17.8 ± 1.26 to −24.6 ± 1.72, and PDI displayed an acceptable size distribution. Transmission electron microscopy revealed a spherical shape with ~200 nm size. Fourier transform infrared spectroscopic analysis showed the physicochemical stability of CDDP@PLs, and differential scanning calorimetry analysis showed the loss of the crystalline nature of cisplatin in liposomes. In vitro release study of CDDP@PLs at pH 7.4 depicted the lower release rate of cisplatin (less than 40%), and at a pH of 6.5, an almost 65% release rate was achieved compared to the release rate at pH 5.5 (more than 80%) showing the tumor-specific drug release. The cytotoxicity study showed the improved cytotoxicity of CDDP@PLs compared to cisplatin solution in MDA-MB-231 and SK-OV-3 cell lines, and fluorescence microscopy also showed enhanced cellular internalization. The acute toxicity study showed the safety and biocompatibility of the developed carrier system for the potential delivery of chemotherapeutic agents. These studies suggest that CDDP@PLs could be utilized as an efficient delivery system for the enhancement of therapeutic efficacy and to minimize the side effects of chemotherapy by releasing cisplatin at the tumor site.

Sign in / Sign up

Export Citation Format

Share Document