Influence of Free Stream Turbulence Intensity on Heat Transfer and Flow Around Four In-Line Elliptic Cylinders in Cross Flow

2010 ◽  
Vol 8 (1) ◽  
Author(s):  
Ramadan Y. Sakr ◽  
Nabil M. Berbish ◽  
Ali A. Abd-Aziz
Keyword(s):  
Heat Transfer ◽  
Turbulence Intensity ◽  
Average Nusselt Number ◽  
Free Stream ◽  
Flow Characteristics ◽  
Cross Flow ◽  
Elliptic Cylinder ◽  
Major Axis ◽  
Free Stream Turbulence ◽  
Spacing Ratio

The effect of free stream turbulence intensity on heat transfer and flow characteristics around four in-line elliptic cylinders in cross flow was experimentally and numerically investigated. The elliptic cylinders examined had an axis ratio (b/c) of (1:3) with a zero angle of attack (where the major axis is horizontal) and were heated under a constant heat flux condition. Three different sizes of free stream turbulence producing grids (screen) inserted at a distance of 300 mm the upstream test cylinders are used to study the effect of the free stream turbulence. The turbulence intensity levels of 5.6%, 8.3% and 10.5% are obtained from the grid sizes. The effects of cylinder spacing ratio (L/c) were examined within Reynolds number (based on free stream velocity and major axis length) ranging from 3640 to 66240. It was observed that the local and average Nusselt numbers of the tested elliptic cylinders increase with increasing the free stream turbulence intensity. The results showed that the maximum enhancement ratio for the average Nusselt number (for the tested cylinder with grid and for the single elliptic cylinder without grid) was found to be about 1.93 and was obtained for the second elliptic cylinder in four in-line cylinders at L/c=1.5, Re=6150 with free stream turbulence intensity of 10.5%. Also, the flow characteristics varied drastically with both the longitudinal spacing ratio and the inserted grid (screen). Moreover, an empirical correlation for the average Nusselt number of the second elliptic cylinder of the four in-line cylinders was obtained as function of Reynolds number and free stream turbulence intensity.

Free-Stream Turbulence From a Circular Wall Jet on a Flat Plate Heat Transfer and Boundary Layer Flow

1989 ◽  
Vol 111 (1) ◽  
pp. 78-86 ◽  
Author(s):  
R. MacMullin ◽  
W. Elrod ◽  
R. Rivir
Keyword(s):  
Heat Transfer ◽  
Turbulence Intensity ◽  
Free Stream ◽  
Flow Characteristics ◽  
Surface Profile ◽  
Constant Heat Flux ◽  
Length Scale ◽  
Wall Jet ◽  
Reynolds Analogy ◽  
Free Stream Turbulence

The effects of the longitudinal turbulence intensity parameter of free-stream turbulence (FST) on heat transfer were studied using the aggressive flow characteristics of a circular tangential wall jet over a constant heat flux surface. Profile measurements of velocity, temperature, integral length scale, and spectra were obtained at downstream locations (2 to 20 x/D) and turbulence intensities (7 to 18 percent). The results indicated that the Stanton number (St) and friction factor (Cf) increased with increasing turbulence intensity. The Reynolds analogy factor (2St/Cf) increased up to turbulence intensities of 12 percent, then became constant, and decreased after 15 percent. This factor was also found to be dependent on the Reynolds number (Rex) and plate configuration. The influence of length scale, as found by previous researchers, was inconclusive at the conditions tested.

scholarly journals The Effects of Incident Turbulence and Moving Wakes on Laminar Heat Transfer in Gas Turbines

1992 ◽  
Author(s):  
K. Dullenkopf ◽  
R. E. Mayle
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Gas Turbines ◽  
Free Stream ◽  
Cross Flow ◽  
Turbulence Parameter ◽  
Constant Acceleration ◽  
Free Stream Turbulence ◽  
Laminar Boundary Layers ◽  
Good Agreement

The effect of free-stream turbulence and moving wakes on augmenting heat transfer in accelerating laminar boundary layers is considered. First, the the effect of free-stream turbulence is re-examined in terms of a Nusselt number and turbulence parameter which correctly account for the free-stream acceleration and a correlation for both cylinders in cross flow and airfoils with regions of constant acceleration is obtained. This correlation is then used in a simple quasi-steady model to predict the effect of periodically passing wakes on airfoil laminar heat transfer. A comparison of the predictions with measurements shows good agreement.

Direct Numerical Simulations of a Transonic Tip Flow With Free-Stream Disturbances

2013 ◽  
Author(s):  
Andrew P. S. Wheeler ◽  
Richard D. Sandberg
Keyword(s):  
Heat Transfer ◽  
High Performance ◽  
Free Stream ◽  
Separation Bubble ◽  
Cross Flow ◽  
Turbulence Models ◽  
Navier Stokes ◽  
Computational Domain ◽  
Free Stream Turbulence ◽  
Gap Height

In this paper we use direct numerical simulation to investigate the unsteady flow over a model turbine blade-tip at engine scale Reynolds and Mach numbers. The DNS is performed with a new in-house multi-block structured compressible Navier-Stokes solver purposely developed for exploiting high-performance computing systems. The particular case of a transonic tip flow is studied since previous work has suggested compressibility has an important influence on the turbulent nature of the separation bubble at the inlet to the gap and subsequent flow reattachment. The effects of free-stream turbulence, cross-flow and pressure-side boundary-layer on the tip flow aerodynamics and heat transfer are investigated. For ‘clean’ in-flow cases we find that even at engine scale Reynolds numbers the tip flow is intermittent in nature (neither laminar nor fully turbulent). The breakdown to turbulence occurs through the development of spanwise modes with wavelengths around 25% of the gap height. Cross-flows of 25% of the streamwise gap exit velocity are found to increase the stability of the tip flow, and to significantly reduce the turbulence production in the separation bubble. This is predicted through in-house linear stability analysis, and confirmed by the DNS. For the case when the inlet flow has free-stream turbulence, viscous dissipation and the rapid acceleration of the flow at the inlet to the tip-gap causes significant distortion of the vorticity field and reductions of turbulence intensity as the flow enters the tip gap. This means that only very high turbulence levels at the inlet to the computational domain significantly affect the tip heat transfer. The DNS results are compared with RANS predictions using the Spalart-Allmaras and k–ω SST turbulence models. The RANS and DNS predictions give similar qualitative features for the tip flow, but the size and shape of the inlet separation bubble and shock positions differ noticeably. The RANS predictions are particularly insensitive to free-stream turbulence.

Experimental and Numerical Investigation of Natural Convection Heat Transfer in Horizontal Elliptic Annuli

2008 ◽  
Vol 6 (1) ◽  
Author(s):  
Ramadan Y. Sakr ◽  
Nabil S. Berbish ◽  
Ali A. Abd-Aziz ◽  
Abdalla Said Hanafi
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Average Nusselt Number ◽  
Orientation Angle ◽  
Elliptic Cylinder ◽  
Major Axis ◽  
Radius Ratio ◽  
Hydraulic Radius ◽  
Axis Ratio

Experimental and numerical studies for natural convection in two dimensional regions formed by a constant flux heat horizontal elliptic tube concentrically located in a larger, isothermally cooled horizontal cylinder were investigated. Both ends of the annulus are closed. Experiments were carried out for the Rayleigh number based on the equivalent annulus gap length ranges from 1.12x107 up to 4.92x107; the elliptic tube orientation angle varies from 0o to 90o and the hydraulic radius ratio, HRR, was 6.4. These experiments were carried out for the axis ratio of an elliptic tube (minor/major=b/c) of 1:3. The numerical simulation for the problem is carried out by using commercial CFD code. The effects of the orientation angle as well as other parameters such as elliptic cylinder axis ratio and hydraulic radius ratio on the flow and heat transfer characteristics are investigated numerically. The numerical simulations covered a range of elliptic tube axis ratios from 0.1 to 0.98 and for the hydraulic radius ratios from 1.5 to 6.4. The results showed that the average Nusselt number increases as the orientation angle of the elliptic cylinder increases from 0o (the major axis is horizontal) to 90o (the major axis is vertical) and with the Rayleigh number as well. Also, the average Nusselt number decreases with the increase of the hydraulic radius ratio. An increase up to 1.75 and further increases in the hydraulic radius ratio leads to an increase in the average Nusselt number. The axis ratio of the elliptic cylinder has an insignificant effect on the average Nusselt number. Both the average and local Nusselt number from the experimental results are compared with those obtained from the CFD code.Both the fluid flow and heat transfer characteristics for different operating and geometric conditions are illustrated velocity vectors and isotherm contours that were obtained from the CFD code. Also, two correlation equations that relate the average Nusslet number with the Rayleigh number, orientation angle, and hydraulic radius ratio and axis ratio are obtained.

Aero-Thermal Performance of a Two-Dimensional Highly Loaded Transonic Turbine Nozzle Guide Vane: A Test Case for Inviscid and Viscous Flow Computations

1992 ◽  
Vol 114 (1) ◽  
pp. 147-154 ◽  
Author(s):  
T. Arts ◽  
M. Lambert de Rouvroit
Keyword(s):  
Heat Transfer ◽  
Turbulence Intensity ◽  
Static Pressure ◽  
Free Stream ◽  
Guide Vane ◽  
Free Stream Turbulence ◽  
Nozzle Guide Vane ◽  
Transonic Turbine ◽  
Nozzle Guide ◽  
Highly Loaded

This contribution deals with an experimental aero-thermal investigation around a highly loaded transonic turbine nozzle guide vane mounted in a linear cascade arrangement. The measurements were performed in the von Karman Institute short duration Isentropic Light Piston Compression Tube facility allowing a correct simulation of Mach and Reynolds numbers as well as of the gas to wall temperature ratio compared to the values currently observed in modern aero engines. The experimental program consisted of flow periodicity checks by means of wall static pressure measurements and Schlieren flow visualizations, blade velocity distribution measurements by means of static pressure tappings, blade convective heat transfer measurements by means of platinum thin films, downstream loss coefficient and exit flow angle determinations by using a new fast traversing mechanism, and free-stream turbulence intensity and spectrum measurements. These different measurements were performed for several combinations of the free-stream flow parameters looking at the relative effects on the aerodynamic blade performance and blade convective heat transfer of Mach number, Reynolds number, and free-stream turbulence intensity.

scholarly journals Comparison of k-ε Models in Predicting Heat Transfer and Skin Friction Under High Free Stream Turbulence

1996 ◽  
Author(s):  
Ganesh R. Iyer ◽  
Savash Yavuzkurt
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Boundary Layer ◽  
Skin Friction ◽  
Turbulence Intensity ◽  
Free Stream ◽  
Skin Friction Coefficient ◽  
Empirical Correlations ◽  
Free Stream Turbulence ◽  
Boundary Layer Equations

Calculations of the effects of high free stream turbulence (FST) on heat transfer and skin friction in a flat plate turbulent boundary layer using different k-ε models (Launder-Sharma, K-Y Chien, Lam-Bremhorsi and Jones-Launder) are presented. This study was carried out in order to investigate the prediction capabilities of these models under high FST conditions. In doing so, TEXSTAN, a partial differential equation solver which is based on the ideas of Patankar and Spalding and solves steady-flow boundary layer equations, was used. Firstly, these models were compared as to how they predicted very low FST (≤ 1% turbulence intensity) cases. These baseline cases were tested by comparing predictions with both experimental data and empirical correlations. Then, these models were used in order to determine the effect of high FST (>5% turbulence intensity) on heat transfer and skin friction and compared with experimental data. Predictions for heat transfer and skin friction coefficient for all the turbulence intensities tested by all the models agreed well (within 1–8%) with experimental data. However, all these models predicted poorly the dissipation of turbulent kinetic energy (TKE) in the free stream and TKE profiles. Physical reasoning as to why the aforementioned models differ in their predictions and the probable cause of poor prediction of free-stream TKE and TKE profiles are given.

Effects of Extended Jet Holes to Heat Transfer and Flow Characteristics of the Jet Impingement Cooling

2019 ◽  
Vol 141 (8) ◽  
Author(s):  
Ahmet Ümit Tepe ◽  
Kamil Arslan ◽  
Yaşar Yetişken ◽  
Ünal Uysal
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Average Nusselt Number ◽  
Flat Surface ◽  
Flow Characteristics ◽  
Cross Flow ◽  
Jet Impingement ◽  
Target Surface ◽  
Impingement Cooling ◽  
Compressor Power

In this study, effects of extended jet holes to heat transfer and flow characteristics of jet impingement cooling were numerically investigated. Cross-flow in the impinging jet cooling adversely affects the heat transfer on the target surface. The main purpose of this study is to reduce the negative effect of cross-flow on heat transfer by extending jet holes toward the target surface with nozzles. This study has been conducted under turbulent flow condition (15,000 ≤ Re  ≤  45,000). The surface of the turbine blade, which is the target surface, has been modeled as a flat plate. The effect of the ribs, placed on the target surface, on the heat transfer has been also investigated, and the results were compared with the flat surface. The parameters such as average and local Nusselt numbers on the target surface, flow characteristics, and compressor power have been examined in detail. It was obtained from the numerical results that the average Nusselt number increases with decreasing the gap between the target surface and the nozzle. In addition, the higher average Nusselt number was obtained on the flat surface than the ribbed surface. The lowest compressor power was achieved in the 5Dj nozzle gap for the flat surface and in the 4Dj nozzle gap for the ribbed surface.

scholarly journals Turbulence Intensity, Length Scale, and Heat Transfer Around Stagnation Line of Cylinder and Model Blade

1999 ◽  
Author(s):  
V. P. Maslov ◽  
B. I. Mineev ◽  
K. N. Pichkov ◽  
A. N. Secundov ◽  
A. N. Vorobiev ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Turbulence Intensity ◽  
Free Stream ◽  
Turbulence Models ◽  
Leading Edge ◽  
Circular Cylinders ◽  
Length Scale ◽  
Stagnation Line ◽  
Free Stream Turbulence ◽  
Wide Range

A hot-wire technique was used to measure turbulence characteristics in the vicinity of the stagnation line of circular cylinders and a turbine blade model (a chord length of 1 metre). Heat transfer intensity at the stagnation line of the cylinders was also measured by on-surface probes. The experiments were carried out in a wide range of the Reynolds number based on the blade leading edge/cylinder diameter, D (Re = 2.103–2.106) and integral length scale of free-stream turbulence, Le (Le = 0.1–10D) at two values of free stream turbulence intensity, Tu (Tu = 0.02 and 0.10). Along with the experimental data results of the 2D RANS computations are presented of the flow and heat transfer at the circular cylinder with the use of two turbulence models: a two-equation, k-ω SST, model of Menter, and a new two-equation, ν1-L, model developed in the course of the present study.

Sign in / Sign up

Export Citation Format

Share Document