scholarly journals Microstructural Characterization and Mechanical Properties of Similar and Dissimilar Al Alloys Joined using Friction Stir Welding

2018 ◽  
Vol 14 (1) ◽  
pp. 19-28
Author(s):  
Kharia Salman Hassan
Keyword(s):  
Friction Stir Welding ◽  
Welding Speed ◽  
Shot Peening ◽  
Rotational Speed ◽  
Microstructural Characterization ◽  
Tensile Tests ◽  
Welding Parameters ◽  
Welding Temperature ◽  
Rotating Speed ◽  
Friction Stir

The influence of pre- shot peening and welding parameters on mechanical and metallurgical properties of dissimilar and similar aluminum alloys AA2024-T3 and AA6061-T6 joints using friction stir welding have been studied. In this work, numbers of plates were equipped from sheet alloys in dimensions (150*50*6) mm then some of them were exposed to shot peening process before friction stir welding using steel ball having diameter 1.25 mm for period of 15 minutes. FSW joints were manufactured from plates at three welding speeds (28, 40, 56 mm/min) and welding speed 40mm/min was chosen at a rotating speed of 1400 rpm for welding the dissimilar pre- shot plates. Tow joints were made at rotational speed of 1000 rpm and welding speed of 40m/min from shot and without shot peening plats. Welding temperature was measured in three zones using thermocouple. Micro hardness (HV) and tensile tests were performed to evaluate the mechanical characteristic of the joints. The results show a decay in mechanical qualities when the welding speed was increased and the best result was at (28) mm/min and the opposite result was obtained when rotational speed increased and pre-shot contributed in improving of this decay at 88% of welding speed (40) mm/min and 98%  at the rotational speed of 1000 rpm.      

Mechanical Property of Friction Stir Welded Retardant Magnesium Alloy Joint

2011 ◽  
Vol 295-297 ◽  
pp. 1929-1932
Author(s):  
Yi Min Tu ◽  
Ran Feng Qiu ◽  
Hong Xin Shi ◽  
Xin Zhang ◽  
Ke Ke Zhang
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Friction Stir Welding ◽  
Magnesium Alloy ◽  
Welding Speed ◽  
Rotational Speed ◽  
Maximum Strength ◽  
Welding Parameters ◽  
Tool Rotational Speed ◽  
Friction Stir

In order to obtain better understanding of the friction stir weldability of the magnesium alloy and provide some foundational information for improving mechanical properties of retardant magnesium alloy joints. A retardant magnesium alloy was weld using the method of friction stir welding. The influence of welding parameters on the strength of the joint was investigated. The maximum strength of 230 MPa was obtained from the joint welded at the tool rotational speed of 1000 r/min and welding speed of 750 mm/min.

Effect of Welding Parameters on Mechanical and Microstructural Properties of Dissimilar Aluminum Alloy Joints Produced by Friction Stir Welding

2014 ◽  
Vol 592-594 ◽  
pp. 250-254 ◽  
Author(s):  
Sabitha Jannet ◽  
P. Koshy Mathews
Keyword(s):  
Friction Stir Welding ◽  
Rolling Direction ◽  
Structural Evolution ◽  
Tensile Tests ◽  
Processing Parameters ◽  
Welding Parameters ◽  
Microstructural Properties ◽  
Rotating Speed ◽  
Friction Stir ◽  
Mechanical And Microstructural Properties

The effect of processing parameters on the mechanical and microstructural properties of dissimilar AA6061 t6–AA5083 0 joints produced by friction stir welding was studied. Different samples were produced by varying the advancing speeds of the tool as 20 and 40 mm/min and by varying the alloy positioned on the advancing side of the tool. In the various trials the rotating speed is varied from 600 to 900 RPM. All the welds were produced perpendicular to the rolling direction for both the alloys. Micro hardness (HV) and tensile tests performed at room temperature were used to evaluate the mechanical properties of the joints. Various tests were performed on the joints previously subjected to ageing. In order to analyze the micro structural evolution of the material, the welds’ zones were observed optically.

Experimental Analysis on Mechanical Properties of Friction Stir Welding in Dissimilar Aluminum Alloys

2020 ◽  
pp. 64-68
Author(s):  
Anganan K ◽  
Narendran RJ ◽  
Naveen Prabhu N ◽  
Rahul Varma R ◽  
Sivasubramaniyam R
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Aluminum Alloys ◽  
Welding Speed ◽  
Rotational Speed ◽  
Copper Alloys ◽  
Welding Parameters ◽  
Tool Rotational Speed ◽  
Friction Stir ◽  
Dissimilar Aluminum Alloys

Friction stir welding (FSW) is an innovative solid state joining technique and has been employed in industries for joining aluminum, magnesium, zinc and copper alloys. The FSW process parameters such as tool, rotational speed, welding speed, axial force, etc play major role in deciding the weld quality. A mathematical modeling was developed based on experiments to predict the tensile strength of dissimilar FSW aluminum alloys. The maximum tensile strength of 210 MPa can be obtained at the tool rotational speed of 1100 rpm, welding speed of 35mm/min and an axial load of 7 kN is the Optimum welding parameters.

scholarly journals Modeling and Optimization of Bobbin Friction Stir Welding for AA6061-T6 alloy Utilizing Response Surface Methodology

2018 ◽  
Vol 26 (4) ◽  
pp. 1-17
Author(s):  
Samir Ali Amin ◽  
Mohannad Yousif Hanna ◽  
Alhamza Farooq Mohamed
Keyword(s):  
Tensile Strength ◽  
Response Surface Methodology ◽  
Friction Stir Welding ◽  
Welding Speed ◽  
Rotational Speed ◽  
Welded Joint ◽  
Welding Parameters ◽  
Friction Stir ◽  
Bending Force ◽  
Speed Range

Bobbin friction stir welding (BFSW) is special kind of friction stir welding. This investigation aims to develop empirical models through mathematical relationships between the welding process parameters and mechanical properties of Aluminum alloy AA6061-T6 welded joint created by using bobbin tool and to find the optimum welding parameters. The welding speed range (40-200 mm/min) and rotational speed range (340-930 rpm) were utilized (as the used input factors) to find their effects on elongation, tensile strength and maximum bending force as the main responses.  These models were built using Design of Experiment (DOE) software ‘version 10’ with Response Surface Methodology (RSM) technique. The models adequacy were tested via the (ANOVA) analysis. The obtained models appeared that as the welding speed or rotational speed increases, the elongation, tensile strength and maximum bending force of the welded joint firstly rise to a maximum value and then drop. The optimum welding parameters were rotational speed (623.949 rpm) and welding speed (128.795 mm/min) with (6.33%), (204 MPa) and (6.216 KN) of elongation, tensile strength and maximum bending force, respectively. A proper harmonization was obtained between the models predicted results and the optimized ones with actual trial with 95% level of confidence.

Experimental Analysis on Mechanical Properties of Friction Stir Welding in Dissimilar Aluminum Alloys

2020 ◽  
pp. 64-68
Author(s):  
K. Anganan ◽  
R.J . Narendran ◽  
N Naveen Prabhu ◽  
R Rahul Varma ◽  
R Sivasubramaniyam
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Aluminum Alloys ◽  
Welding Speed ◽  
Rotational Speed ◽  
Copper Alloys ◽  
Welding Parameters ◽  
Tool Rotational Speed ◽  
Friction Stir ◽  
Dissimilar Aluminum Alloys

Friction stir welding (FSW) is an innovative solid state joining technique and has been employed in industries for joining aluminum, magnesium, zinc and copper alloys. The FSW process parameters such as tool, rotational speed, welding speed, axial force, etc play major role in deciding the weld quality. A mathematical modeling was developed based on experiments to predict the tensile strength of dissimilar FSW aluminum alloys. The maximum tensile strength of 210 MPa can be obtained at the tool rotational speed of 1100 rpm, welding speed of 35mm/min and an axial load of 7 kN is the Optimum welding parameters.

An Optimized Method for Choosing Friction Stir Welding Parameters

2013 ◽  
Vol 706-708 ◽  
pp. 431-434
Author(s):  
Lei Wang ◽  
Li Yang Xie ◽  
Li Hui ◽  
Ping Yun Li ◽  
Jun Gang Ren
Keyword(s):  
Friction Stir Welding ◽  
Welding Speed ◽  
Weld Strength ◽  
Friction Stir Weld ◽  
Welding Parameters ◽  
Rotating Speed ◽  
Friction Stir ◽  
Speed Range ◽  
Dissimilar Friction Stir Weld ◽  
Strength Effect

Effect of rotating speed and welding velocity on properties of 6063-3A21 dissimilar Friction Stir weld was experimental studied, results show that too high or too low welding velocity will result in a decrease of the weld strength; effect of rotating speed on weld strength is relatively small. An optimized method for Choosing Friction Stir Welding parameters was proposed, which include three steps, first, fix a rotating speed through experimental analysis; and then find out reasonable ranges of v/w; finally work out the optimized welding speed range.

Procedure to find out the optimal ranges of process parameters for friction stir welding

2021 ◽  
pp. 146442072199314
Author(s):  
Shubham Verma ◽  
Joy Prakash Misra ◽  
Meenu Gupta
Keyword(s):  
Friction Stir Welding ◽  
Process Parameters ◽  
Tilt Angle ◽  
Welding Speed ◽  
Rotational Speed ◽  
Optical Microscope ◽  
Graphical Analysis ◽  
Friction Stir ◽  
Steepest Ascent ◽  
Vertical Milling Machine

The present study deals with the application of sequential procedure (i.e. steepest ascent) to obtain the optimum values of process parameters for conducting friction stir welding (FSW) experiments. A vertical milling machine is modified by fabricating fixture and tool ( H13 material) for performing FSW operation to join AA7039 plates. The steepest ascent technique is employed to design the experiments at different rotational speed, welding speed, and tilt angle. The ultimate tensile strength is considered as a performance characteristic for deciding the optimal levels. The mechanical and metallurgical characteristics of the joints are studied by executing tensile and microhardness tests. It is concluded from the graphical analysis of the steepest ascent technique that the optimal maximum and minimum values are 1812–1325 r/min for rotational speed, 43–26 mm/min for welding speed, and 2°–1.3° for tilt angle, respectively. Besides, optical microscope and scanning electron microscope are utilized for microstructural and fractographic analyses for a better understanding of the process.

scholarly journals Thermo-mechanical analysis of linear welding stage in friction stir welding - influence of welding parameters

2021 ◽  
pp. 186-186
Author(s):  
Darko Veljic ◽  
Marko Rakin ◽  
Aleksandar Sedmak ◽  
Nenad Radovic ◽  
Bojan Medjo ◽  
...  
Keyword(s):  
Friction Stir Welding ◽  
Heat Generation ◽  
Welding Speed ◽  
Reaction Force ◽  
Material Model ◽  
Element Model ◽  
Welding Parameters ◽  
Al Alloy ◽  
Friction Stir ◽  
Fsw Parameters

The influence of friction stir welding (FSW) parameters on thermo-mechanical behaviour of the material during welding is analysed. An aluminium alloy is considered (Al 2024 T351), and different rotating speed and welding speed are applied. Finite element model consists of the plate (Al alloy), backing plate and welding tool, and it is formed and solved in software package Simulia Abaqus. The influence of the welding conditions on material behaviour is taken into account by application of the Johnson-Cook material model. The rotation of the tool affects the results: if increased, it contributes to an increase of friction-generated heat intensity. The other component of the generated heat, the plastic deformation of the material, is negligibly changed. When the welding speed is increased, the intensity of friction-generated heat decreases, while the heat generation due to plastic deforming increases. Combined, these two effects cause small change of the total heat generation. For the same welded joint length, the plate welded by lower speed will be heated more intensively. The changes of the heat generation influence both the temperature field and reaction force, which are also considered.

Process Parameters Optimization of Friction Stir Welding in Aluminium Alloy 6063-T6 by Taguchi Method

2017 ◽  
Vol 867 ◽  
pp. 97-104 ◽  
Author(s):  
T. Ganapathy ◽  
K. Lenin ◽  
K. Pannerselvam
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Taguchi Method ◽  
Axial Force ◽  
Process Parameters ◽  
Welding Speed ◽  
Rotational Speed ◽  
Process Parameter ◽  
Main Process ◽  
Friction Stir

This paper deals with the effective application of friction stir welding similar to butt joining technique.AL6063 T-6 alloys prepared in 125x 100 x 7mm thickness plate and FSW tool setup were H13 of diameter 25mm rotary tool with straight cylindrical pin profile. The maximum strength was considered for selection of combined process parameter. The process parameters were optimized using Taguchi method. The Rotational speed, welding speed, and axial speed are the main process parameter which taken into our consideration. The optimum process parameters are determined with reference to tensile strength of the joint. From the experiments, it was found the effects of welding parameter are the axial force is highest substantial parameter to determining the tensile strength of the joint. The paper which revealed the optimal values of process parameter are to acquire a maximum tensile strength of friction stir welded AL6063-T6 plates is 101.6Mpa with the combination level of rotational speed, welding speed and axial force are found to be 1100 RPM, 60 mm/min and 12.5 KN. validation test was carried out and results were nearer to the optimized results confirmed by the optimum results.

Experimental Study on Friction Stir Welding of Dissimilar Al 6061 to Trip 780/800 Steel

2014 ◽  
Author(s):  
Xun Liu ◽  
Shuhuai Lan ◽  
Jun Ni
Keyword(s):  
Friction Stir Welding ◽  
Cross Sections ◽  
Welding Speed ◽  
Rotational Speed ◽  
Maximum Temperature ◽  
Friction Stir ◽  
Al 6061 ◽  
Tool Axis ◽  
Edge Temperature ◽  
Welding Force

Friction stir welding (FSW) of dissimilar Al 6061 and TRIP 780/800 steel has been performed under different process parameters, including tool rotational speed, welding speed as well as the relative position of the tool axis to the abutting edge. Temperature and mechanical welding force was recorded during the process. Welding speed has an insignificant effect on either the maximum temperature or welding force. However, it can directly change the length of high temperature duration, which will accordingly influence temperature distribution in the weld and the microstructure. Higher rotational speed can effectively elevate weld temperature through greater amount of heat input. Metallurgical observations on weld cross sections perpendicular to the joint line was performed using both optical and scanning electron microscope. Microstructure evolution was analyzed and related to the force and temperature measurement results during the FSW process.

Sign in / Sign up

Export Citation Format

Share Document