scholarly journals Study the Effect of Welding Heat Input on the Microstructure, Hardness, and Impact Toughness of AISI 1015 Steel

2018 ◽  
Vol 14 (1) ◽  
pp. 118-127 ◽  
Author(s):  
Emad Kh. Hamd ◽  
Abbas Sh. Alwan ◽  
Ihsan Khalaf Irthiea
Keyword(s):  
Corrosion Rate ◽  
Weld Joint ◽  
Heat Input ◽  
Plate Thickness ◽  
Welding Process ◽  
Welding Current ◽  
Low Carbon ◽  
Mig Welding ◽  
The Impact ◽  
Weld Heat

In the present study, MIG welding is carried out on low carbon steel type (AISI 1015) by using electrode ER308L of 1.5mm diameter with direct current straight polarity (DCSP). The joint geometry is of a single V-butt joint with one pass welding stroke for different plate thicknesses of 6, 8, and 10 mm. In welding experiments, AISI 1015 plates with dimensions of 200×100mm and edge angle of 60o from both sides are utilized. In this work, three main parameters related to MIG welding process are investigated, which are welding current, welding speed, heat input and plate thickness, and to achieve that three groups of plates are employed each one consists of three plates. The results indicate that increasing the weld heat input (through changing the current and voltage) leads to an increase in widmanstatten ferrite (WF), acicular ferrite (AF) and polygonal ferrite (PF) in FZ region, and a reduction in grain size. It is observed that the micro-hardness of welded AISI 1015 plate increases as the weld heat input decreases. As well as increasing the weld heat input results in an increase in the width of WM and HAZ and a reduction in the impact energy of the weld joint of AISI 1015 at WM region. Also, it is noted the corrosion rate of weld joint increases with increase of Icorr due to increasing in welding current (heat input), corrosion rate increased up to (0.126µm/yr.) with increasing of heat input up to (1.27 KJ/mm).  

scholarly journals The impact of heat input on the mechanical properties and microstructure of High Strength Low Alloy steel welded joint by GMA welding process

2021 ◽  
Vol 9 (3) ◽  
pp. 299-310 ◽  
Author(s):  
Saadat Ali Rizvi ◽  
Rajnish Singh ◽  
Saurabh Kumar Gupta
Keyword(s):  
Mechanical Properties ◽  
Alloy Steel ◽  
Heat Input ◽  
Gma Welding ◽  
Hsla Steel ◽  
Welding Process ◽  
Welding Current ◽  
High Strength ◽  
Low Alloy Steel ◽  
The Impact

The basic aim of this study was to find a relationship between heat input and mechanical properties of high strength low alloy steel (HSLA) welded joints and also elaborate its effect on microstructure. The combined effect of welding current, voltage and speed i.e. Heat Input on mechanical properties of High Strength Low Alloy Steel (ASTM A242 type-II) weldments have been studied in the present work. HSLA steel work pieces were welded by Gas metal arc welding (GMAW) process under varying welding current, arc voltage, and welding speed. Total nine samples were prepared at different heat input level i.e. 1.872 kJ/mm, 1.9333 kJ/mm, 2.0114 kJ/mm, 2.1 kJ/mm, 2.1956 kJ/mm, 2.296 kJ/mm, 2.4 kJ/mm, 2.5067 kJ/mm and 2.6154 kJ/mm It was observed that as heat input increases the ultimate tensile strength and microhardness of weldment decreased while impact strength increased and it was also observed that on increasing the heat input grain size of microstructure tends to coarsening it is only due to decreasing in cooling rate.

Influence of Weld Heat Input on Weld Joint between B610CF and 16MnR Steel

2010 ◽  
Vol 154-155 ◽  
pp. 421-424
Author(s):  
Tian Hui Zhang ◽  
Hong Cai Fu ◽  
Wen Min Liu ◽  
Yun Chun Cheng ◽  
Ren Ping Xu
Keyword(s):  
Impact Toughness ◽  
Weld Joint ◽  
Heat Affected Zone ◽  
Heat Input ◽  
Experimental Results ◽  
Distinct Difference ◽  
Shielded Metal Arc Welding ◽  
Metal Arc Welding ◽  
The Impact ◽  
Weld Heat

The influence of weld heat input on weld joint between B610CF and 16MnR steel using shielded metal arc welding method was investigated by metallographic experiment and mechanical properties experiment. Metallographic experimental results show that in welded metal with the increasing of weld heat input the quantity of bainite is decreased and crystalline grain is larger; but in both B610CF and 16MnR steel heat affected zone, with the increasing of weld heat input there is no distinct difference in microstructure. Mechanical property experimental results show that in weld metal with the increasing of weld heat input the impact toughness decreases, but in both B610CF and 16MnR heat affected zone, there is less difference in impact toughness; and there is no distinct difference in tensile strength and plasticity of weld joint, which is consistent with the metallographic experiment results.

scholarly journals Comprehensive Analysis of TIG Welded Inconel–718 Alloy for Different Heat Input Conditions

2018 ◽  
Vol 7 (3.6) ◽  
pp. 206
Author(s):  
P Jerold Jose ◽  
M Dev Anand
Keyword(s):  
Tensile Properties ◽  
Heat Input ◽  
Inconel 718 ◽  
Welding Process ◽  
Welding Current ◽  
Tig Welding ◽  
Welding Parameters ◽  
Inconel 718 Alloy ◽  
Weld Joints ◽  
Welding Heat Input

In this research, the effects of heat input on tensile properties and microstructure were investigated for super alloy Inconel-718 sheets weld by Tungsten Inert Gas (TIG) welding process. The tensile properties and microstructure of weld joints were evaluated. The experiment was conducted with six different combinations of welding parameters like welding current, voltage and welding speed, which were give in six different welding heat input combinations of welding parameters. The experimental results shows that the welding joints weld with low welding heat input was yield higher tensile properties. From the experimentation it was understand that the tensile properties increases when the welding heat input decrease. Drastic grain coarsening was evidenced when the heat input was increases. For the weld joints experimented in this research it was also observed that amount of laves phase was increased with increase in the welding heat input which is the major fact for noticeable variation in the ultimate tensile strength of the weld joints welded by TIG welding process with different welding heat input. 

scholarly journals Influence of Current Feeding Position of Duplex Current Feeding MIG Welding on Droplet Heat Quantity

Materials ◽  
2019 ◽  
Vol 12 (21) ◽  
pp. 3590
Author(s):  
Atsuhito Aoki ◽  
Shinichi Tashiro ◽  
Hideaki Kurokawa ◽  
Manabu Tanaka
Keyword(s):  
Welding Process ◽  
Welding Current ◽  
Mig Welding ◽  
Secondary Current ◽  
Pure Argon ◽  
Large Current ◽  
Heat Quantity ◽  
Feeding Speed ◽  
Wire Feeding ◽  
Simplified Calculation

Pure argon metal inert gas (MIG) welding is expected to offer the possibility to obtain high toughness weld joints. However, due to its arc instability and low wettability, it is difficult to apply pure argon MIG to a practical welding structure. In order to solve these problems, an improved MIG welding process with a duplex current feeding (DCF-MIG) mechanism was developed. In the DCF-MIG process, the welding current and the wire feeding speed are independently controlled by an additionally feeding secondary current from a secondary power source. Thereby, DCF-MIG can supply a large current compared to conventional MIG under the same deposition rate. In this study, to consider the influence of the secondary current feeding position of DCF-MIG on droplet heat quantity, droplet heat quantity was measured by calorimetry. As a result, the droplet heat quantity was found to be increased significantly with the increase of the distance between the primary current feeding point and secondary current feeding point. The increase of the droplet heat quantity in the DCF-MIG process had a strong effect on improving bead shape and penetration. The droplet heat quantity with the effective current value of DCF-MIG was derived from the simplified calculation and the results roughly agreed with the experimental data.

Experimental Study on the Single-Sided Double-Point Resistance Welding of Bus Roof Skin

2014 ◽  
Vol 680 ◽  
pp. 97-101
Author(s):  
Hai Bin Huang ◽  
Jian Chun Liu ◽  
Xiao Long Ke ◽  
Xiao Hui Lin
Keyword(s):  
Double Point ◽  
Low Carbon Steel ◽  
Welding Process ◽  
Welding Current ◽  
Resistance Welding ◽  
Galvanized Steel ◽  
Low Carbon ◽  
Support Mechanism ◽  
Experiment Platform ◽  
Weld Area

In order to weld the skin and skeleton of bus roof, it analysis the welding process of bus Outer Roof-panels , and specify the weld area and solder joint distance of outer roof-panel firstly , then built a single-sided double-point resistance welding experiment platform for bus outer roof-panels, the platform consists of guide、gantry、gantry moving mechanism、 pneumatic torch、electrode support mechanism、transformers、torch lateral movement organizations and torch longitudinal movement phenomenon . it set the unevenness of the skin and the skeleton as 1mm, single-sided double-point resistance welding experiment was conducted on the welding experiment platform. The experimental results of welding area visual examination and tear experiments indicate that welding heat will penetrate the skeleton when the welding current is greater than 11.0KA;the welding Reliability of galvanized steel is better than low carbon steel.

Effect of the FCAW Welding Process and Post Weld Heat Treatment on the Properties and Microstructure of the Weld Joints of Heat Treated 4330V Steel

2015 ◽  
Vol 809-810 ◽  
pp. 437-442
Author(s):  
Jacek Górka ◽  
Michał Miłoszewski
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Weld Metal ◽  
Heat Input ◽  
Large Diameter ◽  
Welding Process ◽  
Post Weld Heat Treatment ◽  
High Toughness ◽  
Interpass Temperature ◽  
Weld Heat

4330V is a high strength, high toughness, heat treatable low alloy steel for application in the oil, gas and aerospace industries. It is typically used for large diameter drilling parts where high toughness and strength are required. The research describes the effect of preheat temperature, interpass temperature, heat input, and post weld heat treatment on strength, hardness, toughness, and changes to microstructure in the weld joint. Welding with the lower heat input and no post weld heat treatment resulted in optimal mechanical properties in the weld metal. Austempering at 400 °C resulted in optimal mechanical properties in the HAZ. Increasing preheat and interpass temperature from 340 °C to 420 °C did not improve Charpy V-notch values or ultimate tensile strength in the weld metal or heat affected zones. The higher temperature increased the width of the heat affected zone. Austempering at 400 °C reduced HAZ hardness to a level comparable to the base metal. Both tempering and austempering at 400 °C for 10 hours reduced toughness in the weld metal.

The Impact of Adscititious Longitudinal Magnetic Field on CO2 Welding Process

2012 ◽  
Vol 538-541 ◽  
pp. 1447-1450 ◽  
Author(s):  
Shu Yuan Jiang ◽  
Xiao Wei Wang ◽  
Huan Ming Chen ◽  
Pin Liu
Keyword(s):  
Magnetic Field ◽  
High Speed ◽  
Longitudinal Magnetic Field ◽  
Short Circuit ◽  
Welding Process ◽  
Welding Current ◽  
High Speed Photography ◽  
Current Decay ◽  
Co2 Welding ◽  
The Impact

Aiming at the welding arc can act with the magnetic field, has electrical quasi-neutral and electrical conductivity. This paper introduced an adscititious longitudinal magnetic field to control the CO2 welding process and used the Hanover Welding Quality Analyzer to acquire the real-time welding signal. Meanwhile, the short circuit behavior of CO2 welding under the adscititious longitudinal magnetic field, was monitored with the High-speed Photography System. The results show that when the excitation current in an optimal range, the welding current decay and the frequency of short circuit transition is uniform and faster, smaller droplet size and the welding process is more stability than welding without adscititious magnetic field.

Influence of heat input and solubilizing heat treatment on the impact properties of SAW joints in SAF 2205 duplex steel

2012 ◽  
Vol 1381 ◽  
Author(s):  
M. Merlin ◽  
R. Vazquez-Aguilar ◽  
C. Soffritti ◽  
A. Reyes-Valdes
Keyword(s):  
Heat Treatment ◽  
Heat Input ◽  
Welding Process ◽  
Optical Microscope ◽  
Image Analyzer ◽  
Secondary Phases ◽  
Impact Properties ◽  
Steel Joints ◽  
Saf 2205 ◽  
The Impact

ABSTRACTIn this study the influence of heat input (HI) and heat treatment on submerged arc welded duplex SAF 2205 steel joints has been evaluated. In particular, multi-pass welding operations have been performed on 18 mm thick plates using four different heat inputs; a post-weld solubilizing heat treatment has been carried out in order to reduce the microstructural effects on the structure of the heat affected zone (HAZ). Instrumented impact strength tests have been performed on Charpy samples machined from the welded joints; the total absorbed energy and the two complementary contributions of initiation and propagation energies have been evaluated and correlated to the percentages of ferrite and austenite. The microstructures and the fracture profiles have been observed using an optical microscope (OM) and quantitatively analyzed by means of an image analyzer. A scanning electron microscope (SEM) equipped by energy dispersive X-ray spectroscopy (EDS) has been used to study the fractured surfaces. Hardness profiles have been performed across the joints in order to verify the hardness variations. A total absence of secondary phases has been found on the joints due to the performing of a suitable solubilizing heat treatment after the welding process. The results have shown that the impact properties of the samples have been mostly affected by the different heat inputs; in some cases a partial welding penetration has been found.

scholarly journals A Study on Vertical Upward Welding of Dissimilar Material and Thickness of Thin Plates Using Novel TIG Welding Process

2019 ◽  
Author(s):  
Ngo Huu Manh ◽  
Nguyen Van Anh ◽  
Murata Akihisa ◽  
Hideno Terasaki
Keyword(s):  
Base Metal ◽  
Heat Input ◽  
Weld Zone ◽  
Welding Process ◽  
Welding Current ◽  
Tig Welding ◽  
Dissimilar Material ◽  
Thin Plates ◽  
Welding Defects ◽  
Welding Position

A study about influence of heat input on welding defects in vertical upward welding position for dissimilar material and thickness using a new variation of TIG welding torch is done with support of advanced inspection methods SEM and EBSD. With vertical upward welding position, control heat input plays an important role to keep the weld stabilization without defects. On the other hand, TIG welding process using a conventional TIG torch (conventional TIG welding process) has low efficiency and it is difficult to control heat input with high accuracy. So, it is considered that using conventional TIG torch is still a challenge for welding thin plates. In this case, a new variation of TIG torch has been developed. This torch used a constricted nozzle to improve plasma arc characteristics. As a result, it can control efficiently the heat input to prevent the excessive or insufficiency for joining thin sheets. For evaluation of welding quality, advanced examination methods SEM and EBSD were applied to directly observe the welding defects. From the results, the formation mechanism of blowhole inside weld zone in case of welding dissimilar material and thickness was discussed. It is pointed out that when sufficient welding current, the change from weld zone to base metal is uniform, no welding defects such as blowhole was seen. However, in case of low welding current, the thinner base metal is insufficient fusion and the change between weld zone and base metal is not uniform. The blowhole was observed at SS400 material side.

scholarly journals Multi-Objective Optimization of MIG Welding and Preheat Parameters for 6061-T6 Al Alloy T-Joints Using Artificial Neural Networks Based on FEM

Coatings ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 998
Author(s):  
Qing Shao ◽  
Fuxing Tan ◽  
Kai Li ◽  
Tatsuo Yoshino ◽  
Guikai Guo
Keyword(s):  
Process Parameters ◽  
Welding Speed ◽  
Heat Input ◽  
Pareto Front ◽  
Welding Process ◽  
Residual Deformation ◽  
Welding Deformation ◽  
Mig Welding ◽  
Preheat Temperature ◽  
Multi Objective

To control the welding residual stress and deformation of metal inert gas (MIG) welding, the influence of welding process parameters and preheat parameters (welding speed, heat input, preheat temperature, and preheat area) is discussed, and a prediction model is established to select the optimal combination of process parameters. Thermomechanical numerical analysis was performed to obtain the residual welding deformation and stress according to a 100 × 150 × 50 × 4 mm aluminum alloy 6061-T6 T-joint. Owing to the complexity of the welding process, an optimal Latin hypercube sampling (OLHS) method was adopted for sampling with uniformity and stratification. Analysis of variance (ANOVA) was used to find the influence degree of welding speed (7.5–9 mm/s), heat input (1500–1700 W), preheat temperature (80–125 °C), and preheat area (12–36 mm). The range of research parameters are according to the material, welding method, thickness of the welding plate, and welding procedure specification. Artificial neural network (ANN) and multi-objective particle swarm optimization (MOPSO) was combined to find the effective parameters to minimize welding deformation and stress. The results showed that preheat temperature and welding speed had the greatest effect on the minimization of welding residual deformation and stress, followed by the preheat area, respectively. The Pareto front was obtained by using the MOPSO algorithm with ε-dominance. The welding residual deformation and stress are the minimum at the same time, when the welding parameters are selected as preheating temperature 85 °C and preheating area 12 mm, welding speed is 8.8 mm/s and heat input is 1535 W, respectively. The optimization results were validated by the finite element (FE) method. The error between the FE results and the Pareto optimal compromise solutions is less than 12.5%. The optimum solutions in the Pareto front can be chosen by designers according to actual demand.

Sign in / Sign up

Export Citation Format

Share Document