scholarly journals Impact of SiC on The Mechanical and Thermal Properties of Banana Fiber Reinforced Epoxy Composites

Author(s):  
Mayank Agarwal

Abstract: This work investigates the mechanical properties (Tensile Strength & Impact Strength) and thermal properties (Thermal conductivity & diffusivity) of a natural fiber composite that includes banana fiber as reinforcement in epoxy (LY 556) matrix as the base material with the addition of silicon carbide particles by 5% and 10% by weight. This Banana Fiber Reinforced Epoxy Composite (BFREC) prepared by hand lay-up technique. After curing for a sufficient period, samples taken out and tested. The results suggest that on increasing SiC wt% in the matrix, there is enhancement of its tensile strength, impact strength, and thermal conductivity. Bulk density also increases while thermal diffusivity decreases. Due to low density as compared to metals, improved tensile and impact strength and low elongation at break of banana fibers, BFREC composite with SiC have very good potential use in the various sectors. Keywords: Banana fiber, SiC, hand layup technique, mechanical characterization, thermal conductivity, thermal diffusivity

Author(s):  
Gurminder Singh ◽  
Pulak M Pandey

In the present paper, mechanical and thermal properties of rapidly manufactured copper parts were studied. The combination of three-dimensional printing and ultrasonic assisted pressureless sintering was used to fabricate copper parts. First, the ultimate tensile strength and thermal conductivity were compared between ultrasonic assisted and conventional pressureless sintered samples. The homogenously mixing of particles and local heat generation by ultrasonic vibrations promoted the sintering driving process and resulted in better mechanical and thermal properties. Furthermore, response surface methodology was adopted for the comprehensive study of the ultrasonic sintering parameters (sintering temperature, heating rate, and soaking time with ultrasonic vibrations) on ultimate tensile strength and thermal conductivity of the fabricated sample. Analysis of variance was performed to identify the significant factors and interactions. The image processing method was used to identify the surface porosity at different parameter levels to analyse the experimental results. High ultimate tensile strength was obtained at high sintering temperature, long soaking time, and slow heating rate with low surface porosity. After 60 min of soaking time, no significant effect was observed on the thermal conductivity of the fabricated sample. The significant interactions revealed less effect of soaking time at low sintering temperatures for ultimate tensile strength and less effect of heating rate at low sintering temperatures for thermal conductivity. Multi-objective optimization was carried out to identify parameters for maximum ultimate tensile strength and maximum thermal conductivity.


2018 ◽  
Vol 22 ◽  
pp. 23-33 ◽  
Author(s):  
Seenaa I. Hussein

In this research, we have prepared epoxy/graphene nanocomposites (graphene content: 1, 3, 5, 7, and 9 wt%) to investigate some mechanical (impact strength, hardness, and Brazilian tests) and thermal properties (thermal conductivity and thermogravimetric analysis). Our results show that the impact strength, hardness, and compression strength values increased to 5.04 kJ/m2, 79.8, and 27.85 MPa, respectively, as increasing graphene content up to 5 wt% and then decreased for further increasing of the graphene content. The observed reduction in the hardness could be attributed to the samples brittleness. On the other hand, the thermal conductivity increased with increasing the graphene content because of the high thermal conductivity of graphene and thus the efficiency increase with increasing of graphene content. In addition, the thermal stability of epoxy/graphene composite increase compared with pure epoxy resin, while the activation energy for samples consists of 9 wt% graphene greater than those containing 1 wt% graphene.


2017 ◽  
Vol 31 (7) ◽  
pp. 882-895 ◽  
Author(s):  
DI Chukov ◽  
AA Stepashkin ◽  
VV Tcherdyntsev ◽  
LK Olifirov ◽  
SD Kaloshkin

Structural, mechanical, and thermal properties of polyphenylene sulfide (PPS) filled with Al-Cu-Fe quasicrystals particles were studied. It was shown that the introducing of quasicrystalline fillers into the polymer matrix results in the increase in Young’s modulus, hardness, and toughness of the polymer. Quasicrystalline fillers can improve thermal properties of PPS, including heat resistance index, Vicat softening temperature, thermal diffusivity, and thermal conductivity.


2020 ◽  
pp. 002199832095318
Author(s):  
RMR Shagor ◽  
F Abedin ◽  
R Asmatulu

The use of nanofillers to enhance the properties of fiber reinforced composites is limited due to the adverse effect on mechanical properties caused by agglomeration of these nanofillers in the matrix materials. In this study, graphene nanoflakes were functionalized with silane moiety to improve its dispersion, stability and bond strengths in the polymer matrices of the carbon fiber reinforced composites. Wet layup process was applied to incorporate graphene nanocomposites into the dry carbon fibers to make composite panels following the curing cycle of the epoxy and hardener. The impacts of the functionalized graphene on the mechanical and thermal properties of carbon reinforced composite were investigated in detail by tensile test, differential scanning calorimetry, dynamic mechanical analysis and scanning electron microscopy (SEM) analysis. It was observed that nanocomposites with 0.5 wt% silanized graphene exhibited maximum tensile strength and modulus of elasticity, indicating that 0.50 wt% silane functionalized graphene was the optimum nanofiller composition amongst the three different compositions investigated. The nanocomposites with 0.25 wt% and 0.50 wt% nanofillers showed improved ductility compared to the control sample. Based on the SEM studies on the crack zones, major morphological changes were observed after the salinization process. The interfacial interaction between epoxy and silane moiety of the graphene and reduction in the tendency to agglomerate could account for the improved properties of the nanocomposite observed here. Nanocomposites with silanized graphene showed overall higher glass transition temperature (Tg) and tensile strength than those with pristine graphene and control samples.


2018 ◽  
Vol 789 ◽  
pp. 221-225
Author(s):  
Nattapol Dedruktip ◽  
Wasan Leelawanachai ◽  
Nuchnapa Tangboriboon

Alumina fiber is a ceramic material used as a dispersed phase or filler to reinforce the mechanical and improve thermal properties of natural rubber via vulcanization process at curing temperature 150°C. The amount of alumina fiber added in natural rubber was varied from 0 to 50 phr on 100 phr of natural rubber in a sulfur curing system. Adding 10 phr alumina fiber affects to obtain the best natural rubber composite samples having good mechanical and thermal properties. Tensile strength, elongation at break, Young’s modulus and thermal conductivity of adding 10 phr whisker alumina fiber encoded NR-Al-10 are equal to 14.38±1.95 MPa, 1038.4±41.45%, 545.63±25.67 MPa and 0.2376±0.0003 W/m.K, respectively, better than those of pure natural rubber compounds without adding alumina fiber. Tensile strength, elongation at break, Young’s modulus and thermal conductivity of natural rubber without adding alumina fiber are equal to 14.06±6.03 MPa, 949.41±52.15%, 496.32±8.54 MPa and 0.2500±0.0003 W/m.K, respectively.


2012 ◽  
Vol 472-475 ◽  
pp. 1937-1940
Author(s):  
Dong Yan Ren ◽  
Xiao Hong Li ◽  
Zhi Hua Li

Polyurethane-modified epoxy resin was prepared with Polyurethane prepolymer(PUP). The effects of the PUP content and epoxy resin type on mechanical and thermal properties of materials were discussed. The results indicate that the tensile strength and impact strength of the material increase to maximum successively, and then decrease with the increasing addition of PUP. When the mass fraction of PUP was 15%, the tensile strength and the impact strength of materials were all the best. There were significant differences in mechanical and thermal properties of material for different epoxy, and the best results were cured epoxy TDE-85.


2021 ◽  
Vol 3 (2) ◽  
Author(s):  
P. Sivaranjana ◽  
V. Arumugaprabu

AbstractThe usage of banana natural fibers along with polymer matrix composites had created much interest among the researchers due to their low cost, easy availability, strength and enhancement in properties such as mechanical, wear, electrical and thermal. Banana plant is cultivated all over the world which is familiarly used as food products especially banana fruit as well as many household items made from banana fibers. The natural fiber extracted from the banana stem proves to be a potential reinforcement in the composite manufacturing. This review is very much needed because of the enormous research reported on the banana fiber reinforced polymer composites, with such an excellent property offered by this banana fiber reinforcement the impact of hybridization and its need also to be addressed. This brief review article gives a detail information about the combinations of various hybrid composites produced using the banana fiber along with various other natural/synthetic fibers in the polymer matrixes and its performance improvement especially in the mechanical and thermal properties. From the review it was inferred that 30–50% increase in all the mechanical properties such as Tensile, Flexural and Impact strength. Also in addition an enhancement in thermal and moisture resistance also noted. In addition during this review the research gap observed is that the development of bio composites based on banana fiber is very limited and also the influence of banana fiber along with bio resin needs to be studied. The properties such as fatigue, fire resistance also to be analyzed using the banana fiber reinforcement.


2020 ◽  
Vol 11 (04) ◽  
pp. 245-262
Author(s):  
Budrun Neher ◽  
Rakib Hossain ◽  
Kaniz Fatima ◽  
M. A. Gafur ◽  
Md. Abul Hossain ◽  
...  

2015 ◽  
Vol 659 ◽  
pp. 446-452 ◽  
Author(s):  
Supatra Pratumshat ◽  
Phutthachat Soison ◽  
Sukunya Ross

In this work, the mechanical and thermal properties of pineapple leaf fiber (PALF)/poly (lactic acid) (PLA) composites were studied. Pineapple leaf fibers were pretreated with 4 %wt sodium hydroxide solution followed by various silane solutions i.e. γ-(aminopropyl) trimethoxy silane (APS), γ-methacrylate propyl trimethoxy (A174) and bis [3-(triethoxysilyl) propyl] tetrasulfide (Si69). FTIR results show a significant functional groups of C=O and C=C of methacrylic group, NH2group and Si-O which are the characteristic of these silane coupling agents. SEM micrographs of pretreated PALF showed a rough surface while untreated and silane treated PALF revealed less roughness. It was found that the tensile strength at break of PLA is 56 MPa and tensile strength of composites decreased when fiber content increased. The tensile modulus of silane treated PALF composites were higher than PLA, whereas their impact strength were similar to PLA. Si69 treated PALF showed lower impact strength compared to the others silanes treated fiber which indicates more phase separation between fiber and matrix. This is related to high percentage of crystallinity of composite from Si69 treated fiber. It was also found that the addition of PALF did not change the glass transition temperature and melting temperature of PLA while the percentage of crystallinity increases as the fiber content increased. In addition WAXS study of composite from Si69 treated fiber reveals sharp crystalline peaks of PLA while the others silane treatments show amorphous characteristic of PLA.


2011 ◽  
Vol 410 ◽  
pp. 59-62 ◽  
Author(s):  
Punmanee Juntuek ◽  
Chaiwat Ruksakulpiwat ◽  
Pranee Chumsamrong ◽  
Yupaporn Ruksakulpiwat

From our previous study, natural rubber (NR) was used to improve toughness of poly (lactic acid) (PLA). Impact strength and elongation at break of PLA was increased when adding NR. Moreover, by using NR-g-GMA as compatibilizer for PLA and NR blend, impact strength and elongation at break was improved. However, tensile strength and modulus of PLA/NR blend with and without NR-g-GMA were decreased. In this study, calcium carbonate (CaCO3) and vetiver grass fiber were used as fillers in PLA/NR blend. With the addition of CaCO3 into PLA/NR blend with NR-g-GMA, impact strength and modulus of the composite were further increased with a loss in tensile strength. In contrast, the addition of vetiver grass fiber into PLA/NR blend with NR-g-GMA led to an increase in tensile strength and modulus and a decrease in impact strength and elongation at break. The onset degradation temperatures of PLA composites were lower than that of PLA and PLA/NR blend.


Sign in / Sign up

Export Citation Format

Share Document