scholarly journals Circle Microstrip Antenna Simulation for Frequency 3.5 GHz

2021 ◽  
Vol 1 (1) ◽  
pp. 1-4
Author(s):  
Wildan Wildan ◽  
Dwi Astuti Cahyasiwi ◽  
Syah Alam ◽  
Mohd Azman Zakariya ◽  
Harry Ramza
Keyword(s):  
Dielectric Constant ◽  
Patch Antenna ◽  
Microstrip Antenna ◽  
Microstrip Line ◽  
Return Loss ◽  
Tangent Loss ◽  
Substrate Thickness ◽  
Total Radiation ◽  
Circular Patch Antenna ◽  
Working Frequency

This research proposed microstrip circular patch antenna simulation at a working frequency 3500 MHz. The antenna has been designed using a Duroid RT5880 substrate with dielectric constant (εr) = 2.2, substrate thickness (h) = 1.575 mm, and tangent loss = 0.0009 with microstrip line feeding. The simulation result, return loss value obtained -26.385, VSWR value 1.09, gain value 7.64 dBi, total radiation efficiency value -0.6489 dB, and bandwidth value 72 MHz (3468.8 MHz – 3541.9 MHz).

scholarly journals Inverted dual U slot loaded truncated microstrip patch antenna for wireless applications

2018 ◽  
Vol 7 (2.21) ◽  
pp. 151
Author(s):  
Kavitha Thandapani ◽  
Shiyamala Subramani
Keyword(s):  
Dielectric Constant ◽  
Resonant Frequency ◽  
Loss Tangent ◽  
Patch Antenna ◽  
Return Loss ◽  
Microstrip Patch Antenna ◽  
Wireless Applications ◽  
Microstrip Patch ◽  
Dielectric Constant And Loss ◽  
Circular Patch Antenna

Dual U Slot Loaded Truncated Microstrip Patch Antenna is designed for wireless applications. The proposed geometry comprised of two inverted U slots in truncated circular patch antenna operation covering 2.24 to 2.72 GHZ frequency bands are obtained. It is found that the slot and truncated is used to improve the bandwidth and return loss respectively. The resonant frequency is found to be 2.5GHZ. The bandwidth of the proposed antenna for lower and upper resonant frequency is found to be 19.2%. The proposed antenna is fed by 50Ω co-axial probe feed and simulated on Rogers RT/duroid5880 substrate.  Rogers RT/duroid 5880 substrate has dielectric constant and loss tangent of 2.2 and 0.0009 respectively. An air gap is used in this proposed design for tuning the desired frequencies and increasing the bandwidth. The antenna shows an acceptable gain of 2.1dB to 5.7dB with unidirectional pattern over the obtained frequency band. 

scholarly journals 26 GHz phase shifters for multi-beam nolen matrix towards fifth generation (5G) technology

2019 ◽  
Vol 8 (3) ◽  
pp. 1028-1035
Author(s):  
Norhudah Seman ◽  
Nazleen Syahira Mohd Suhaimi ◽  
Tien Han Chua
Keyword(s):  
Dielectric Constant ◽  
Microstrip Line ◽  
Return Loss ◽  
Phase Shifter ◽  
Low Cost ◽  
Phase Shifters ◽  
Substrate Thickness ◽  
Fifth Generation ◽  
Compact Size ◽  
Better Than

This paper presents the designs of phase shifters for multi-beam Nolen matrix towards the fifth generation (5G) technology at 26 GHz. The low-cost, lightweight and compact size 0° and 45° loaded stubs and chamfered 90°, 135° and 180° Schiffman phase shifters are proposed at 26 GHz. An edge at a corner of the 50 Ω microstrip line Schiffman phase shifter is chamfered to reduce the excess capacitance and unwanted reflection. However, the Schiffman phase shifter topology is not relevant to be applied for the phase shifter less than 45° as it needs very small arc bending at 26 GHz. The stubs are loaded to the phase shifter in order to obtain electrical lengths, which are less than 45°. The proposed phase shifters provide return loss better than 10 dB, insertion loss of -0.97 dB and phase difference imbalance of ± 4.04° between 25.75GHz and 26.25 GHz. The Rogers RT/duroid 5880 substrate with dielectric constant of 2.2 and substrate thickness of 0.254 mm is implemented in the designs.

scholarly journals A Low Profile Wideband Log Periodic Microstrip Antenna Design for C-Band Applications

2019 ◽  
Vol 8 (2) ◽  
pp. 48-52 ◽  
Author(s):  
M. Yerlikaya ◽  
S. S. Gültekin ◽  
D. Uzer
Keyword(s):  
Dielectric Constant ◽  
Microstrip Antenna ◽  
Microstrip Line ◽  
Ground Plane ◽  
Antenna Design ◽  
Tangent Loss ◽  
Low Profile ◽  
Measurement Results ◽  
Simulation Results ◽  
5 Ghz

In this study, a wideband low profile microstrip antenna design for C-band applications is presented. The proposed antenna consists of a monopol log periodic patch in the equilateral triangular dimensions with the microstrip line fed and a rectangular ground plane. The antenna has 9×19.8 mm2 overall size, thickness of 1.6 mm and 4.3 dielectric constant. According to the simulation results, the proposed antenna has a very wide bandwidth while operating in the frequency band of 4.25-7.95 GHz and 5 GHz resonance frequency. The proposed antenna was also prototyped on FR4 substrate with the 0.02 tangent loss and the measurement results were quite similar by the simulated results.

scholarly journals Circular Polarization of the Square, Circular, Triangle, and Hexagonal Microstrip Antenna

2020 ◽  
Vol 3 (1) ◽  
pp. 5
Author(s):  
Nurhayati Nurhayati ◽  
Paulen Aulia Lutfia ◽  
Raimundo Eider Figueredo Sobrinho ◽  
Alexandre Manicoba De Oliveira ◽  
João Francisco Justo Filho ◽  
...  
Keyword(s):  
Resonance Frequency ◽  
Circular Polarization ◽  
Patch Antenna ◽  
Microstrip Antenna ◽  
Return Loss ◽  
Axial Ratio ◽  
Patch Shape ◽  
Circular Patch ◽  
Hexagonal Shape ◽  
Circular Patch Antenna

Microstrip antenna with circular polarization can be applied for many applications. Some microstrip antenna with square, circular, triangular, and hexagonal shape has been designed to get return loss, axial ratio, and radiation performance. We compare twelve microstrip antenna by maintaining its substrate dimension, feeding shape, and outer patch dimension. Even though antenna has a circular patch, it doesn’t always produce circular polarization. From the simulation, we found that with add some structure, the antenna can reach multiband resonance from 1 to 6 GHz. The Circular patch antenna reached seven numbers of the multiband resonance frequency. The hexagonal patch antenna reaches the highest directivity as 9.53 dBi. The circular polarization is achieved for a square and Hexagonal patch shape with axial ratio value is 1.96 dB at 4 GHz and  1.26 dB at 4.1 GHz sequentially at phi 900 and theta 900. 

scholarly journals Realisasi dan Pengujian Antena Mikrostrip Array 4 Elemen dengan Polarisasi Melingkar untuk Aplikasi 4G/LTE

2018 ◽  
Vol 6 (2) ◽  
pp. 244
Author(s):  
EDDY WIYANTO ◽  
SYAH ALAM ◽  
BUDI HARSONO
Keyword(s):  
Reflection Coefficient ◽  
Circular Polarization ◽  
Microstrip Line ◽  
Axial Ratio ◽  
Tangent Loss ◽  
Substrate Thickness ◽  
Working Frequency ◽  
Tan Δ ◽  
Element Array ◽  
4G Lte

ABSTRAKPenelitian ini mengusulkan desain antena mikrostrip array empat elemen dengan polarisasi melingkar pada frekuensi kerja 2300 MHz untuk aplikasi 4G/LTE. Antena telah dirancang dan dipabrikasi menggunakan substrat jenis FR-4 Epoxy dengan nilai konstanta dielektrik (Ɛr) = 4.3, ketebalan substrat (h) = 1.6 mm dan loss tangen (tan δ) = 0.0265 dengan pencatu microstrip line. Polarisasi melingkar dengan axial ratio ≤ 3 dB dihasilkan dengan menggunakan metode truncated corner sedangkan untuk meningkatkan nilai gain digunakan metode array empat elemen. Dari hasil proses pengukuran diperoleh nilai koefisien refleksi sebesar -16.52 dB, VSWR sebesar 1.37 pada frekuensi kerja 2300 MHz dengan bandwidth yang diperoleh dari hasil pengukuran adalah 400 MHz (2050 MHz - 2450 MHz). Metode truncated corner berhasil menghasilkan polarisasi melingkar dengan nilai axial ratio 1.745 dB dan berhasil menghasilkan nilai gain sebesar 9.04 dB pada frekuensi kerja 2300 MHz untuk aplikasi LTE.Kata kunci: Antena, mikrostrip, koefisien refleksi, array, truncated corner ABSTRACTThis research proposed a four-element microstrip array antenna design withcircular polarization at a working frequency of 2300 MHz for 4G / LTEapplications. The antenna has been designed and fabricated using a FR-4 Epoxy substrate with a dielectric constant value (Ɛr) = 4.3, substrate thickness (h) = 1.6 mm and tangent loss (tan δ) = 0.0265 with microstrip line feeding. The circular polarization with axial ratio ≤3 dB was generated using the truncated corner method while for increasing the gain value used the four element array method. From the result of the measurement process, the reflection coefficient value is obtained -16.52 dB, VSWR of 1.37 at 2300 MHz working frequency with bandwidth obtained from the measurement result is 400 MHz (2050 MHz - 2450 MHz). The truncated corner method succeeded in generating a circular polarization with the axial ratio of 1.745 dB and succeeded to obtain the gain of 9.04 dB at work frequency of 2300 MHz for LTE application. Keywords: Antena, microstrip, reflection coefficient, array, truncated corner

PERANCANGAN ANTENA MIKROSTRIPRECTANGULAR

Jurnal Teknik ◽  
2018 ◽  
Vol 7 (1) ◽  
Author(s):  
Heru Abrianto
Keyword(s):  
Dielectric Constant ◽  
Patch Antenna ◽  
Wireless Lan ◽  
Microstrip Antenna ◽  
Wireless Local Area Network ◽  
Local Area Network ◽  
Local Area ◽  
Area Network ◽  
Dual Polarization ◽  
Feeding Technique

Microstrip antenna which designed with dual feeding at 2.4 GHz and 5.8 GHz can meet WLAN (Wireless Local Area Network) application.Antenna fabrication use PCB FR4 double layer with thickness 1.6 mm and dielectric constant value 4.4. The length of patch antenna according to calculation 28.63 mm, but to get needed parameter length of patch should be optimized to 53 mm. After examination, this antenna has VSWR 1.212 at 2.42 GHz and 1.502 at 5.8 GHz, RL -13.94 dB at 2.42 GHz and -20.357 dB at 5.8 GHz, gain of antenna 6.16 dB at 2.42 GHz and 6.91 dB at 5.8 GHz, the radiation pattern is bidirectional. Keywords : microstrip antenna, wireless LAN, dual polarization, single feeding technique

Comb Shaped Triple Band Microstrip Antenna for Wireless Communication

2021 ◽  
Vol 9 (4) ◽  
pp. 379-382
Keyword(s):  
Dielectric Constant ◽  
Wireless Communication ◽  
High Frequency ◽  
Microstrip Antenna ◽  
Return Loss ◽  
Experimental Results ◽  
High Frequency Structure Simulator ◽  
Frequency Structure ◽  
Triple Band

A comb shaped microstrip antenna is designed by loading rectangular slots on the patch of the antenna. The antenna resonating at three different frequencies f1 = 5.35 GHz, f2 = 6.19 GHz and f3= 8.15 GHz. The designed antenna is simulated on High Frequency Structure Simulator software [HFSS] and the antenna is fabricated using substrate glass epoxy with dielectric constant 4.4 having dimension of 8x4x0.16 cms. The antenna shows good return loss, bandwidth and VSWR. Experimental results are observed using Vector Analyzer MS2037C/2.

scholarly journals Design of a High Gain Compact Circular Microstrip Patch Antenna for X-Band

2018 ◽  
Vol 7 (2.6) ◽  
pp. 168
Author(s):  
Madhukant Patel ◽  
Veerendra Singh Jadaun ◽  
Kanhiya Lal ◽  
Piyush Kuchhal
Keyword(s):  
Patch Antenna ◽  
Microstrip Antenna ◽  
High Efficiency ◽  
High Gain ◽  
Microstrip Patch Antenna ◽  
Radar Sensors ◽  
Microstrip Patch ◽  
X Band ◽  
Circular Patch Antenna ◽  
Power Radiation

This paper presents design a High Gain Small Size Microstrip Patch Antenna for X-Band applications such as Moving target RADAR sensor, Motion detector, Microwave camera, Ground Penetration RADAR sensors, wall penetration scanners and many medical applications. Now we have to selected circular geometry of micro strip patch antenna because circular geometry overcomes edge effect of antenna. The proposed antenna is designed to operate for X-band at the centre frequency of 10 GHz. The proposed Circular patch antenna is compact and easy to body mount with a high efficiency. The compactness makes it a better choice as compare with other antenna in the X-band. The proposed antenna shows a very sharp return loss of -46 dB at 10 GHz having narrow pattern with a good gain of 4.7 dBi. This enables its use in high directional applications. The paper represents the designing steps, and the simulation result obtained. The software used here for this circular shaped microstrip antenna is IE3D. Various parameters such as gain, power, radiation pattern, and S11 of the antenna are mentioned.

Optimum Patch Dimension Ratio of T-Shaped Microstrip Antenna

2013 ◽  
Vol 684 ◽  
pp. 303-306
Author(s):  
Eugene Rhee ◽  
Ji Hoon Lee
Keyword(s):  
High Frequency ◽  
Microstrip Antenna ◽  
Microstrip Line ◽  
Return Loss ◽  
Impedance Matching ◽  
Feeding Method ◽  
High Frequency Structure Simulator ◽  
Feeding Methods ◽  
Coaxial Probe ◽  
Dimension Ratio

There are various feeding methods of antenna like as coaxial probe, coupling, parasitic elements, and impedance matching. This paper adopted the microstrip line method as the feeding method of the antenna. The high frequency structure simulator is used to analyze the characteristics of the T-shaped microstrip antenna with various patch dimensions. In comparison with the basic microstrip antenna, this proposed T-shaped microstrip antenna with 40.38 % of patch dimensions has the optimum characteristics of resonant frequency, return loss, and radiation pattern at 2.0 GHz band.

UWB RECTANGULAR SLOTTED MICROSTRIP PATCH ANTENNA IN PROXIMITY OF HUMAN ARM MODEL

2016 ◽  
Vol 78 (5-4) ◽  
Author(s):  
Muhammad Syafiq Noor Azizi ◽  
Azahari Salleh ◽  
Adib Othman ◽  
Najmiah Radiah Mohamad ◽  
Nor Azlan Aris ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Patch Antenna ◽  
Free Space ◽  
Return Loss ◽  
Microstrip Patch Antenna ◽  
Ultra Wideband ◽  
Uwb Antenna ◽  
Study Behavior ◽  
Microstrip Patch ◽  
Human Arm

In this paper, we study behavior of Ultra wideband antenna which is Rectangular Slotted Microstrip Patch Antenna. Then, the antenna operated in proximity of human arm model. Furthermore, the antenna is designed on a FR-4 substrate with dielectric constant of 4.3 and thickness 1.6 mm. This antenna simulated in CST Microwave Studio software. In order to test the antenna, an arm model was numerically modelled. The study shows properties and performances of antenna when it is placed in three situations which in free space, outside and inside of human arm model. The properties of UWB antenna in term of return loss, gain, directivity and radiation pattern in the three situations is simulated and discussed.

Sign in / Sign up

Export Citation Format

Share Document