High-temperature carbon plastics based on thermoreactive polyimide binder

2020 ◽  
pp. 89-102
Author(s):  
M. I. Valueva ◽  
I. V. Zelenina ◽  
M. A. Zharinov ◽  
M. A. Khaskov
Keyword(s):  
Glass Transition ◽  
High Temperature ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Strength Properties ◽  
High Glass Transition Temperature ◽  
Reinforced Plastics ◽  
Carbon Plastics ◽  
Fundamental Possibility ◽  
Fiber Reinforced Plastics

The article presents results of studies of experimental carbon plastics based on thermosetting PMRpolyimide binder. Сarbon fiber reinforced plastics (CFRPs) are made from prepregs prepared by melt and mortar technologies, so the rheological properties of the polyimide binder were investigated. The heat resistance of carbon plastics was researched and its elastic-strength characteristics were determined at temperatures up to 320°С. The fundamental possibility of manufacturing carbon fiber from prepregs based on polyimide binder, obtained both by melt and mortar technologies, is shown. CFRPs made from two types of prepregs have a high glass transition temperature: 364°C (melt) and 367°C (solution), with this temperature remaining at the 97% level after boiling, and also at approximately the same (86–97%) level of conservation of elastic strength properties at temperature 300°С.

scholarly journals Cure Kinetics Modeling of a High Glass Transition Temperature Epoxy Molding Compound (EMC) Based on Inline Dielectric Analysis

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1734
Author(s):  
Erick Franieck ◽  
Martin Fleischmann ◽  
Ole Hölck ◽  
Larysa Kutuzova ◽  
Andreas Kandelbauer
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Kinetic Parameters ◽  
Measurement Techniques ◽  
Process Conditions ◽  
Dielectric Analysis ◽  
High Glass Transition Temperature ◽  
General Process ◽  
Molding Compound

We report on the cure characterization, based on inline monitoring of the dielectric parameters, of a commercially available epoxy phenol resin molding compound with a high glass transition temperature (>195 °C), which is suitable for the direct packaging of electronic components. The resin was cured under isothermal temperatures close to general process conditions (165–185 °C). The material conversion was determined by measuring the ion viscosity. The change of the ion viscosity as a function of time and temperature was used to characterize the cross-linking behavior, following two separate approaches (model based and isoconversional). The determined kinetic parameters are in good agreement with those reported in the literature for EMCs and lead to accurate cure predictions under process-near conditions. Furthermore, the kinetic models based on dielectric analysis (DEA) were compared with standard offline differential scanning calorimetry (DSC) models, which were based on dynamic measurements. Many of the determined kinetic parameters had similar values for the different approaches. Major deviations were found for the parameters linked to the end of the reaction where vitrification phenomena occur under process-related conditions. The glass transition temperature of the inline molded parts was determined via thermomechanical analysis (TMA) to confirm the vitrification effect. The similarities and differences between the resulting kinetics models of the two different measurement techniques are presented and it is shown how dielectric analysis can be of high relevance for the characterization of the curing reaction under conditions close to series production.

Viscoelastic Behavior of Segmented Elastomers

1967 ◽  
Vol 40 (4) ◽  
pp. 1105-1110 ◽  
Author(s):  
Stuart L. Cooper ◽  
Arthur V. Tobolsky
Keyword(s):  
Hydrogen Bonding ◽  
Glass Transition ◽  
High Temperature ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Viscoelastic Behavior ◽  
Temperature Transition ◽  
Hydrogen Bonding Interactions ◽  
Structural Nature ◽  
Hard Segments

Abstract Viscoelastic behavior of linear segmented elastomers was examined. The unusual properties found in spandex systems are also observable in hydrocarbon block co-polymers, indicating that hydrogen bonding interactions are perhaps not essential. Low temperature properties of segmented systems are governed by the structural nature of the associated flexible segments, which determines the value of the major glass transition temperature (Tg). It appears that an association of the hard segments provides a broad temperature range of enhanced rubbery modulus. This occurs between the major Tg and a secondary high temperature transition.

Experimental Research on Mechanical Behavior of GFRP Bars under High Temperature

2011 ◽  
Vol 71-78 ◽  
pp. 3591-3594 ◽  
Author(s):  
Xiao Lu Wang ◽  
Xiao Xiong Zha
Keyword(s):  
Glass Transition ◽  
High Temperature ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Epoxy Resin ◽  
High Temperatures ◽  
Glass Fibers ◽  
Ultimate Tensile Stress ◽  
Gfrp Bars ◽  
Tensile Test Result

Experimental results on tensile mechanics properties of GFRP bars at high temperatures are present in this paper. Thirty commercially produced GFRP tensile specimens of 8mm diameter were tested at high temperature ranging from 10°Cup to 500°C. Tensile test result indicates that, the ultimate tensile stress has significant reduction at two temperature zones, one is glass transition temperature of epoxy resin (80-120°C), with strength degradation 22%, the second is the soften temperature of glass fibers(about 400°C), the strength decrease drastically with almost linear rate and remained 33% residual strength at 500°C. The elastic modulus remained unchanged until glass transition temperature of epoxy resin, and the modulus declined linearly with the temperature elevating. Stress-strain relationships of GFRP bars exhibit liner performance even at high temperatures.

Imide Oligomers Containing Pendent and Terminal Phenylethynyl Groups—II

1998 ◽  
Vol 10 (3) ◽  
pp. 273-283 ◽  
Author(s):  
J W Connell ◽  
J G Smith ◽  
P M Hergenrother
Keyword(s):  
Molecular Weight ◽  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Average Molecular Weight ◽  
Adhesive Tape ◽  
High Glass Transition Temperature ◽  
Compressive Properties ◽  
Compression Moulding ◽  
Imide Oligomers

As part of a programme to develop high-performance/high-temperature structural resins for aeronautical applications, imide oligomers containing pendent and terminal phenylethynyl groups were prepared, characterized and the cured resins evaluated as composite matrices. The oligomers were prepared at a calculated number-average molecular weight of 5000 g mol−1 and contained 15–20 mol% pendent phenylethynyl groups. In previous work, an oligomer containing pendent and terminal phenylethynyl groups exhibited a high glass transition temperature (∼313 °C), and laminates therefrom exhibited high compressive properties, but processability, fracture toughness, microcrack resistance and damage tolerance were less than desired. In an attempt to improve these deficiencies, modifications in the oligomeric backbone involving the incorporation of 1,3-bis(3-aminophenoxy)benzene were investigated as a means of improving processability and toughness without detracting from the high glass transition temperature and high compressive properties. The amide acid oligomeric solutions were prepared in N-methyl-2-pyrrolidinone and were subsequently processed into imide powder, thin films, adhesive tape and carbon fibre prepreg. Neat resin plaques were fabricated from imide powder by compression moulding. The maximum processing pressure was 1.4 MPa and the cure temperature ranged from 350 to 371 °C for 1 h for the mouldings, adhesives, films and composites. The properties of the 1,3-bis(3-aminophenoxy)benzene modified cured imide oligomers containing pendent and terminal phenylethynyl groups are compared with those of previously prepared oligomers containing pendent and terminal phenylethynyl groups of similar composition and molecular weight.

scholarly journals Effect of Cutting Temperature on Bending Properties of Carbon Fibre Reinforced Plastics

2019 ◽  
Vol 26 (1) ◽  
pp. 394-401 ◽  
Author(s):  
Ben Wang ◽  
Bowen Yang ◽  
Minghai Wang ◽  
Yaohui Zheng ◽  
Xianjun Hong ◽  
...  
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Carbon Fibre ◽  
Cutting Temperature ◽  
Bending Stress ◽  
Bending Properties ◽  
Reinforced Plastics ◽  
Increasing Temperature ◽  
Carbon Fibre Reinforced Plastics

AbstractHigh cutting temperatures are easily generated during the machining of carbon fibre reinforced plastics (CFRP) and can induce serious damage during machining such as delamination. The purpose of this paper is to study the influence of cutting temperature on the performance of CFRP after machining. CFRP specimens were heated to temperatures within the vicinity of cutting temperatures generated during machining, then air-cooled and their bending properties investigated. The results showed that temperature had significant influence on the bending stress of CFRP. With increasing temperature, bending stress decreased and was lowest when the temperature was close to the glass-transition temperature. It was concluded that the bending properties of CFRP could be seriously affected if the material temperature was close to the glass-transition temperature and maintained for a period. As a result, cutting temperature should be kept lower than the glass transition temperature during machining.

Sign in / Sign up

Export Citation Format

Share Document