scholarly journals Performance, emission and combustion analysis of a compression ignition engine using biofuel blends

2017 ◽  
Vol 21 (1 Part B) ◽  
pp. 511-522 ◽  
Author(s):  
Ilker Ors ◽  
Ali Kahraman ◽  
Murat Ciniviz
Keyword(s):  
Diesel Fuel ◽  
Direct Injection ◽  
Compression Ignition ◽  
Combustion Analysis ◽  
Binary Blend ◽  
Compression Ignition Engine ◽  
Hc Emissions ◽  
Smoke Opacity ◽  
High Level ◽  
No Emissions

This study aimed to investigate the effects on performance, emission, and combustion characteristics of adding biodiesel and bioethanol to diesel fuel. Diesel fuel and blend fuels were tested in a water-cooled compression ignition engine with direct injection. Test results showed that brake specific fuel consumption and volumetric efficiency increased by about 30.6% and 3.7%, respectively, with the addition of bioethanol to binary blend fuels. The results of the blend fuel?s combustion analysis were similar to the diesel fuel?s results. Bioethanol increased maximal in-cylinder pressure compared to biodiesel and diesel fuel at both 1400 rpm and 2800 rpm. Emissions of CO increased by an amount of about 80% for fuels containing a high level of bioethanol when compared to CO emissions for diesel fuel. Using biodiesel, NO emissions increased by an average of 31.3%, HC emissions decreased by an average of 39.25%, and smoke opacity decreased by an average of 6.5% when compared with diesel fuel. In addition, when using bioethanol, NO emissions and smoke opacity decreased by 55% and 17% on average, respectively, and HC emissions increased by an average of 53% compared with diesel fuel.

COMBUSTION AND EMISSIONS CHARACTERISTICS OF A COMPRESSION IGNITION ENGINE FUELLED WITH N-BUTANOL BLENDS

2015 ◽  
Vol 77 (8) ◽  
Author(s):  
I. M. Yusri ◽  
M. K. Akasyah ◽  
R. Mamat ◽  
O. M. Ali
Keyword(s):  
Diesel Fuel ◽  
Engine Speed ◽  
Energy Content ◽  
Direct Injection ◽  
Cetane Number ◽  
Injection System ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Exhaust Temperature ◽  
Blended Fuels

The use of biomass based renewable fuel, n-butanol blends for compression ignition (CI) engine has attracted wide attention due to its superior properties such as better miscibility, higher energy content, and cetane number as compared to other alternatives fuel. In this present study the use of n-butanol 10% blends (Bu10) with diesel fuel has been tested using multi-cylinder, 4-stroke engine with common rail direct injection system to investigate the combustion and emissions of the blended fuels. Based on the tested engine at BMEP=3.5Bar. Based on the results Bu10 fuel indicates lower first and second peak pressure by 5.4% and 2.4% for engine speed 1000rpm and 4.4% and 2.1% for engine speed 2500rpm compared to diesel fuel respectively. Percentage reduction relative to diesel fuel at engine speeds 1000rpm and 2500rpm for Bu10: Exhaust temperature was 7.5% and 5.2% respectively; Nitrogen oxides (NOx) 73.4% and 11.3% respectively.

Parametric study of combustion characteristics in a direct-injection diesel homogeneous charge compression ignition engine with a low-pressurefuel injector

2005 ◽  
Vol 6 (3) ◽  
pp. 215-230 ◽  
Author(s):  
Y Ra ◽  
E J Hruby ◽  
R D Reitz
Keyword(s):  
Numerical Simulations ◽  
Diesel Fuel ◽  
Homogeneous Charge Compression Ignition ◽  
Direct Injection ◽  
Low Pressure ◽  
Combustion Characteristics ◽  
Compression Ignition ◽  
Fuel Injector ◽  
Compression Ignition Engine ◽  
Homogeneous Charge

Homogeneous charge compression ignition (HCCI) combustion is an alternative to current engine combustion systems and is used as a method to reduce emissions. It has the potential nearly to eliminate engine-out NOx emissions while producing diesel-like engine efficiencies, when a premixture of gas-phase fuel and air is burned spontaneously and entirely by an autoignition process. However, when direct injection is used for diesel fuel mixture preparation in engines, the complex in-cylinder flow field and limited mixing times may result in inhomogeneity of the charge. Thus, in order to minimize non-uniformity of the charge, early injection of the fuel is desirable. However, when fuel is injected during the intake or early compression stroke, the use of high-pressure injection is limited by the relatively low in-cylinder gas pressure because of spray impingement on the cylinder walls. Thus, it is also of interest to consider low-pressure injectors as an alternative. In the present paper, the parametric behaviour of the combustion characteristics in an HCCI engine operated with a low-pressure fuel injector were investigated through numerical simulations and engine experiments. Parameters including the start-of-injection (SOI) timing and exhaust gas recirculation were considered, and diesel and n-heptane fuels were used. The results show good agreement of behaviour trends between the experiments and the numerical simulations. With its lower vaporization rates, significant effects of the SOI timing and intake gas temperature were seen for diesel fuel due to the formation of wall films. The modelling results also explained the origin of high-temperature NO x-producing regions due to the effect of the gas density on the spray.

Effect of Premixed Diesel Fuel on Partial HCCI Combustion Characteristics

2014 ◽  
Vol 663 ◽  
pp. 26-33
Author(s):  
Y.H. Teoh ◽  
H.H. Masjuki ◽  
M.A. Kalam ◽  
Muhammad Afifi Amalina ◽  
H.G. How
Keyword(s):  
Diesel Fuel ◽  
Engine Speed ◽  
Direct Injection ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Compression Ignition Engine ◽  
Hcci Combustion ◽  
Light Duty ◽  
Auto Ignition ◽  
Ignition Characteristics

This study investigated the effects of premixed diesel fuel on the auto-ignition characteristics in a light duty compression ignition engine. A partial homogeneous chargecompression ignition (HCCI) engine was modified from a single cylinder, four-stroke, direct injection compression ignition engine. The partial HCCI is achieved by injecting diesel fuel into the intake port of the engine, while maintaining diesel fuel injected in cylinder for combustion triggering. The auto-ignition of diesel fuel has been studied at various premixed ratios from 0 to 0.60, under engine speed of 1600 rpm and 20Nm load. The results for performance, emissions and combustion were compared with those achieved without premixed fuel. From the heat release rate (HRR) profile which was calculated from in-cylinder pressure, it is clearly observed that two-stage and three-stage ignition were occurred in some of the cases. Besides, the increases of premixed ratio to some extent have significantly reduced in NO emission.

scholarly journals Combustion characteristics of compression ignition engine fuelled with rapeseed oil–diesel fuel–n-butanol blends

2021 ◽  
Vol 76 ◽  
pp. 17
Author(s):  
Jakub Čedík ◽  
Martin Pexa ◽  
Bohuslav Peterka ◽  
Miroslav Müller ◽  
Michal Holubek ◽  
...  
Keyword(s):  
Vegetable Oils ◽  
Diesel Fuel ◽  
Rapeseed Oil ◽  
Direct Injection ◽  
Combustion Characteristics ◽  
Solid Particles ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Fuel Blend ◽  
Fuel Blends

Liquid biofuels for compression ignition engines are often based on vegetable oils. In order to be used in compression ignition engine the vegetable oils have to be processed because of their high viscosity or it is also possible to use vegetable oils in fuel blends. In order to decrease the viscosity of the fuel blends containing crude vegetable oil the alcohol-based fuel admixtures can be used. The paper describes the effect of rapeseed oil–diesel fuel–n-butanol blends on combustion characteristics and solid particles production of turbocharged compression ignition engine. The 10% and 20% concentrations of n-butanol in the fuel blend were measured and analysed. The engine Zetor 1204, located in tractor Zetor Forterra 8641 with the power of 60kW and direct injection was used for the measurement. The engine was loaded through power take off shaft of the tractor using mobile dynamometer MAHA ZW500. The measurement was carried out in stabilized conditions at 20%, 60% and 100% engine load. The engine speed was kept at 1950 rpm. Tested fuel blends showed lower production of solid particles than diesel fuel and lower peak cylinder pressure and with increasing concentration of n-butanol in the fuel blend the ignition delay was prolonged and premixed phase of combustion was increased.

scholarly journals An experimental study of the combusition and emission performances of 2,5-dimethylfuran diesel blends on a diesel engine

2017 ◽  
Vol 21 (1 Part B) ◽  
pp. 543-553 ◽  
Author(s):  
Helin Xiao ◽  
Pengfei Zeng ◽  
Liangrui Zhao ◽  
Zhongzhao Li ◽  
Xiaowei Fu
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Operating Conditions ◽  
Effective Pressure ◽  
Compression Ignition Engine ◽  
Brake Mean Effective Pressure ◽  
Combustion Duration ◽  
Significant Difference ◽  
Hc Emissions

Experiments were carried out in a direct injection compression ignition engine fueled with diesel-dimethylfuran blends. The combustion and emission performances of diesel-dimethylfuran blends were investigated under various loads ranging from 0.13 to 1.13 MPa brake mean effective pressure, and a constant speed of 1800 rpm. Results indicate that diesel-dimethylfuran blends have different combustion performance and produce longer ignition delay and shorter combustion duration compared with pure diesel. Moreover, a slight increase of brake specific fuel consumption and brake thermal efficiency occurs when a Diesel engine operates with blended fuels, rather than diesel fuel. Diesel-dimethylfuran blends could lead to higher NOx emissions at medium and high engine loads. However, there is a significant reduction in soot emission when engines are fueled with diesel-dimethylfuran blends. Soot emissions under each operating conditions are similar and close to zero except for D40 at 0.13 MPa brake mean effective pressure. The total number and mean geometric diameter of emitted particles from diesel-dimethylfuran blends are lower than pure diesel. The tested fuels exhibit no significant difference in either CO or HC emissions at medium and high engine loads. Nevertheless, diesel fuel produces the lowest CO emission and higher HC emission at low loads of 0.13 to 0.38 MPa brake mean effective pressure.

scholarly journals Combustion Characteristics and NO Formation Characteristics Modeling in a Compression Ignition Engine Fuelled with Diesel Fuel and Biofuel

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Jean Paul Gram Shou ◽  
Marcel Obounou ◽  
Rita Enoh Tchame ◽  
Mahamat Hassane Babikir ◽  
Timoléon Crépin Kofané
Keyword(s):  
Diesel Fuel ◽  
High Efficiency ◽  
Steam Injection ◽  
Biodiesel Fuel ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Injection Method ◽  
Model Compression ◽  
No Formation ◽  
No Emissions

Compression ignition engine modeling draws great attention due to its high efficiency. However, it is still very difficult to model compression ignition engine due to its complex combustion phenomena. In this work, we perform a theoretical study of steam injection being applied into a single-cylinder four-strokes direct-injection and naturally aspirated compression ignition engine running with diesel and biodiesel fuels in order to improve the performance and reduce NO emissions by using a two-zone thermodynamic combustion model. The results obtained from biodiesel fuel are compared with the ones of diesel fuel in terms of performance, adiabatic flame temperatures, and NO emissions. The steam injection method could decrease NO emissions and improve the engine performances. The results showed that the NO formation characteristics considerably decreased and the performance significantly increased with the steam injection method. The relative errors for computed nitric oxide concentration values of biodiesel fuel and diesel fuel in comparison to the measured ones are 2.8% and 1.6%, respectively. The experimental and theoretical results observed show the highly satisfactory coincidences.

scholarly journals EXPERIMENTAL INVESTIGATION ON AN EXHAUST EMISSION CHARACTERISTICS OF A COMPRESSION IGNITION ENGINE FUELED WITH DIESEL-WATER EMULSION

2021 ◽  
Vol 21 (1) ◽  
pp. 35-45
Author(s):  
Abdulrahman Shakir Mahmood ◽  
Haqi I. Qatta ◽  
Saadi M. D. Al-Nuzal
Keyword(s):  
Diesel Fuel ◽  
Tween 20 ◽  
Water Volume ◽  
Exhaust Emission ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Gas Emissions ◽  
Water Emulsion ◽  
Ci Engine ◽  
Smoke Opacity

One of the main sources of global air pollution is the undesirable gas emissions from diesel engines, as well as the accompanied particulate matters (PM). Consequently, the reduction of their amount and quality is highly recommended for clean environment. The present work includes an attempt to use diesel-water emulsion as a fuel on compression ignition (CI) engine emissions and to investigate its effect on these hurtful discharges. For this reason, tests are carried out on a single cylinder, 4-stroke CI engine with steady speed (1500 rpm) and different loads (0-100 %) operated with various proportions of diesel-water emulsions and compared it to the diesel fuel. Four samples of diesel-water emulsions are prepared at ratios of (5, 10, 15 and 20 %) by water volume in diesel and with help of Tween 20 and Oleic Acid as a surfactant to maintain its stability for long periods of time. Gas emissions of the engine are recorded for CO2, CO, HC, and NOX using an exhaust gas analyzer and smoke opacity using a device of smoke meter. Results reveal that the diesel-water emulsion significantly decreases the NOX emissions and smoke opacity. The highest reduction ratio for NOX and smoke opacity are found in case of fuel emulsion DW20, with values of 32.5 % and 39 % respectively, in comparison with that of diesel fuel.

scholarly journals Experimental analysis on the blends of oxygenated fuels with diesel in a direct injection diesel engine for performance evaluation and emissions

2010 ◽  
Vol 7 (1) ◽  
pp. 229-234 ◽  
Author(s):  
M. P. Sudeshkumar ◽  
G. Devaradjane
Keyword(s):  
Diesel Fuel ◽  
Research Effort ◽  
Direct Injection ◽  
Emission Characteristics ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Performance And Emission ◽  
Combustion Performance ◽  
Oxygenated Compounds ◽  
Engine Emission

Rapid depletion of petroleum reserves and the environmental pollution caused by the growing use of conventional fuels created a challenge before the world that new type of fuels should replace the conventional fuels to achieve the future emission regulations. Hence great deal of research effort has been focused to find alternative fuel. The consideration of oxygenates with diesel fuel is a recent approach receives great attention in reducing the exhaust emissions of an engine The combustion, performance and emission characteristics of diesel fuel and oxygenated blends with diesel are analyzed in a four stroke naturally aspirated single cylinder direct injection compression ignition engine. The additives include 2-Ethoxyethanol (2EE), DiethyleneGlycol Dimethyl ether (DGM) and 2-Methoxyethanol (2ME) and the oxygenated compounds were selected based on the availability, price and oxygen content. These oxygenated compounds are blended with diesel fuel in proportion of 6% by volume. Combustion parameters such as in-cylinder pressure and Heat release rate were studied. The engine emission characteristics of the Compression ignition (CI) engine fuelling with oxygenated blends are studied experimentally. The performance of oxygenates on thermal efficiency and specific fuel consumption were studied. Comparing the combustion, performance and emission, the addition of 2-methoxy ethanol blend shows better performance than other two oxygenated blends with diesel and diesel fuel.

scholarly journals Experimental Investigations of a Compression-Ignition Engine Fuelled with Transesterified-Jatropha BiodieselDiesel Blend

2021 ◽  
Vol 40 (3) ◽  
pp. 474-481
Author(s):  
Gopal Kumar Deshmukh ◽  
Ammenur Rehman ◽  
Rajesh Gupta
Keyword(s):  
Diesel Fuel ◽  
Jatropha Curcas ◽  
Renewable Energy Sources ◽  
Direct Injection ◽  
Engine Performance ◽  
Experimental Investigations ◽  
Exhaust Emission ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Jatropha Curcas Biodiesel

Jatropha-curcas biodiesel has recently been considered as one of the potential renewable energy sources in Asia. This biodiesel is produced through the transesterification process of the non-edible oil obtained from Jatropha-curcas. The properties of this biodiesel are quite similar to those of diesel fuel. However, high viscosity of pure Jatropha-curcas biodiesel adversely affects engine performance. Hence, the percentage of Jatrophacurcas biodiesel that will not cause any adverse effect on the engine must be determined. In this context, this paper experimentally investigates the performance and exhaust emission characteristics of a direct injection compression ignition engine fuelled with 25%, 50% and 100% volume basis Jatropha-curcas biodiesel with diesel. Results showed that the Jatropha-curcas biodiesel and its blends demonstrated lower values for brake thermal efficiency and exhaust emission levels than diesel, but not for nitrogen oxide levels and brake specific fuel consumption. It was observed that the blend containing 25% Jatropha-curcas biodiesel (BD25) was the best alternative for diesel fuel based on engine emissions and overall performance. Therefore, BD25 could be considered a potential alternative fuel for compression ignition engines.

Sign in / Sign up

Export Citation Format

Share Document