Karakteristik Cross Laminated Timber (CLT) dari Kayu Jati Platinum Hasil Penjarangan dan Limbah Batang Kelapa Sawit (Characteristic of Cross Laminated Timber (CLT) from Thinned Platinum Teak and Oil Palm Stem Waste)

2020 ◽  
Vol 8 (3) ◽  
pp. 340
Author(s):  
Dimas Triwibowo ◽  
Prabu Satria Sejati ◽  
Mohamad Gopar ◽  
Sudarmanto Sudarmanto ◽  
Fazhar Akbar ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Oil Palm ◽  
Elaeis Guineensis ◽  
Raw Materials ◽  
Flexural Modulus ◽  
Physical And Mechanical Properties ◽  
Tectona Grandis ◽  
Type A ◽  
Type B ◽  
Cross Laminated Timber

The aim of this study was to determine the physical and mechanical properties of Cross laminated timber (CLT) made from oil palm (Elaeis guineensis. Jacq) stem waste combined with thinned platinum teak (Tectona grandis ) wood. CLT was made into two types, namely CLT type A (teak-palm-teak) and CLT type B (teak-teak-teak). The CLT was 150 cm in length and 20 cm in width, with variation of the thickness of 3,0 cm, 4,5 cm, and 6,0 cm, and the glue spread of 300 g/m². The results showed that CLT type B has better physical and mechanical properties than CLT type A. Generally, CLT made of lamina with a thickness of 4,5 cm showed the best performance of physical and mechanical properties. Platinum teak and palm oil stem waste have the potential to be used as a source of CLT raw materials because of the moisture content, flexural modulus (MOE), and fracture modulus (MOR) that meet the JAS 1152 standard.Keywords: Cross laminated timber, platinum teak, oil palm stem, physical properties, mechanical properties

scholarly journals STUDY OF RECEIVING WOOD AND PLANT PLASTICS WITHOUT BINDERS IN THE PRESENCE OF CATALYSTS OF POLYOXOMETALLATES TYPE

2018 ◽  
Vol 8 (1) ◽  
pp. 132-138
Author(s):  
Виктор Бурындин ◽  
Viktor Buryndin ◽  
Лариса Бельчинская ◽  
Larisa Belchinskaya ◽  
Андрей Савиновских ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Functional Groups ◽  
Hot Pressing ◽  
Raw Materials ◽  
Flexural Modulus ◽  
Chemical Activation ◽  
Physical And Mechanical Properties ◽  
Strength Properties ◽  
Raw Material ◽  
Plastic Properties

The possibility of obtaining wood and plant plastics without a binder (WP-WB) in the presence of a catalyst of man-ganese-containing sodium vanadomolybdophosphate has been investigated. The use of this catalyst makes it possible to reduce the temperature of hot pressing in closed molds from 1,800°C to 1,600°C. The fractional composition of the initial press raw material influences physical and mechanical properties of WP-WB. Higher values of the plastic properties are obtained by using a 0.7 mm fraction, which is associated with an increased specific surface area of the particles compared to 1.3 mm particles. The results has showed that the samples obtained by using the catalyst have increase in strength properties (flexural strength, flexural modulus, hardness) at lower pressing temperature, but reduction of water resistance performance has been observed . This is explained by the increase in the content of functional groups when using a catalyst. The process of obtaining plastic can be broken down into two successive stages: the first is hydrothermal destruction of lignin-carbohydrate complex (initial moisture of the press raw material is 12%, the temperature of hot pressing in closed molds is 160 ... .180 ° C) and partial chemical activation of lignin as a result of hydrogen peroxide and catalyst application; the second stage - formation of plastic with the formation of a network structure due to the formed functional groups. It is established that the values of physical and mechanical properties of WP-WB are higher than those of plastic obtained on the basis of plant raw materials (PP-WB). This can be explained by the fact that lignin of coniferous species has the guaiacylpropane structure, while plant raw material has a hydroxyphenylpropane structure

scholarly journals Determination of Physical and Mechanical Properties of Three-layer Boards of Teak (Tectona grandis), Seike (Cedrelinga catenaeformis) and Mascarey (Hieronima alchorneoides), Company PISMADE S.A., Riobamba Canton, Chimborazo Province

2021 ◽  
Author(s):  
J. Criollo Barahona ◽  
D. Román Robalino ◽  
E. Cabezas ◽  
E. Salazar Castañeda
Keyword(s):  
Mechanical Properties ◽  
Compression Test ◽  
Physical And Mechanical Properties ◽  
Tectona Grandis ◽  
Mechanical Tests ◽  
Hyeronima Alchorneoides ◽  
Commercial Use ◽  
Palabras Clave ◽  
Thickness Measurements

The present investigation aims to determine the physical and mechanical properties in three-layer boards of Teak (Tectona grandis), Seike (Cedrelinga catenaeformis) and Mascarey (Hieronima alchorneoides), from the PISMADE S.A. Company, Canton Riobamba, province of Chimborazo. The three specimens used for each of the species in each of the tests performed were worked on using the ASTM D143-94 standard for the tests of parallel compression, perpendicular compression and flexion, and the DIN-52182 standard, with the main variation in thickness measurements caused by the commercial use established by the company. Mechanical tests showed that Seike had the best results, being superior in two tests: perpendicular compression and flexion. Teak tests gave us results that were superior in the perpendicular compression test. Mascarey, unlike the two species mentioned above, had complications during the trials due to problems with the glue between layers. Keywords: physical and mechanical properties of wood, three-layer boards. Resumen La presente investigación pretende: Determinar las propiedades físicas y mecánicas en tableros tricapa de Teca, Seike (Cedrelinga catenaeformis) y Mascarey (Hyeronima alchorneoides), Empresa PISMADE S.A., cantón Riobamba, provincia de Chimborazo; para lo cual se utilizaron 3 probetas por cada una de las especies en cada uno de los ensayos realizados, las mismas fueron trabajadas con base a la Norma ASTM D143-94 para las pruebas de compresión paralela, compresión perpendicular y flexión y la Norma DIN-52182, teniendo como principal variación en las medidas de espesor debido al uso comercial establecido por la empresa. Las pruebas mecánicas mostraron que Seike tuvo los mejores resultados al ser superior en dos ensayos: Compresión perpendicular y flexión. Los ensayos con Teca nos dieron como resultados que es superior en el ensayo de compresión perpendicular. Mascarey a diferencia de las dos especies mencionadas anteriormente tuvo complicaciones con los ensayos debido a problemas con el pegamento entre capas. Palabras clave: propiedades físicas y mecánicas de la madera, tableros tricapa.

scholarly journals KUALITAS PAPAN PARTIKEL BERDASARKAN KOMPOSISI SEKAM PADI DAN KAYU SENGON DENGAN VARIASI KADAR PEREKAT

2019 ◽  
Vol 7 (2) ◽  
Author(s):  
Dendi Prayoga ◽  
. Dirhamsyah ◽  
. Nurhaida
Keyword(s):  
Mechanical Properties ◽  
Moisture Content ◽  
Rice Husk ◽  
Raw Materials ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
Solid Content ◽  
Particle Board ◽  
Rice Husks ◽  
Wood Processing

This research aimed to examine the physical and mechanical properties of particle boards based on the composition of raw materials and adhesive content and know the treatment of the composition of raw materials and the best adhesive content and meet the standard JIS A 5908-2003. The research was conducted at Wood Workshop Laboratory, Wood Processing Laboratory Faculty of Forestry,Tanjungpura University and Laboratory of PT. Duta Pertiwi Nusantara Pontianak. The adhesive used is Urea Formaldehyde with 52% Solid Content. Comparison of the composition of rice husks and sengon varies namely rice husk 50%: sengon 50%, rice husk 60%: sengon 40% and rice husk 70%: sengon 30%  and variations in the levels of UF adhesives, namely 14% and 16%, with target density 0,7 gr/cm3. The particleboard was 30 cm x 30 cm x 1 cm Pressing at temperature 140oC for 8 minutes, with  pressure of 25 kg/cm2. The research results of the study of density and moisture content meet the standards JIS A 5908-2003. The best particle values of rice husk and sengon  with composition a ratio of  rice husk 50%: sengon 50% , 16% adhesive content  16%, with density value of  0,7072 gr/cm3, moisture content 9,1949 %, thick development 12,3210 %, water absorption 68,8270 %, MOE 12110,7273 kg/cm2, MOR 161,0025 kg/cm2, firmness sticky 1,9320 kg/cm2, screw holding strength 62,3124 kg.Keywords : adhesive, composition, particle board, rice husk, sengon

scholarly journals SIFAT FISIK DAN MEKANIK PAPAN GIPSUM DARI LIMBAH KAYU AKASIA (Acacia mangium Willd) BERDASARKAN KADAR GIPSUM DAN UKURAN SERBUK KAYU

2019 ◽  
Vol 7 (1) ◽  
Author(s):  
Ridho Pratama ◽  
M Dirhamsyah ◽  
. Nurhaida
Keyword(s):  
Mechanical Properties ◽  
Raw Materials ◽  
Acacia Mangium ◽  
Physical And Mechanical Properties ◽  
Powder Size ◽  
Wood Powder ◽  
Gypsum Board ◽  
Randomized Design ◽  
Gypsum Content ◽  
Two Factors

This study aims to examine the physical and mechanical properties of gypsum board from Acacia mangium Willd wood waste based on gypsum content and wood powder size. This study refers to the JIS A 5417-1992 standard. This research were conducted at Wood Work Shop laboratory for the preparation of raw materials, Wood Technology laboratory Faculty of Forestry for board making and testing the physical properties of gypsum boards, and  PT. Duta Pertiwi Nusantara laboratory to test the mechanical properties of the gypsum board. The material used is  A. mangium W. Wood powder, gypsum flour, water and borax. The study uses Factorial Completely Randomized Design (CRD) with two factors, namely factor A (gypsum content) which consists of gypsum content of 400%, 500% and 600% of the weight of A. mangium W. wood powder, and factors B (wood powder size) consists of 20 mesh passes 40 mesh retained and 40 mesh passes 60 mesh retained. The results showed that the density (600% gypsum content of 40 and 60 mesh retained wood powder size), moisture content, thickness swelling, MOE (600% gypsum content of 40 and 60 mesh retained wood powder size) fulfill JIS A5417-1992 standard. The best gypsum board is gypsum board with gypsum content of 600% with a wood powder size is 40 mesh.Keyword: Acacia mangium, gypsum board, gypsum content, wood powder size.

scholarly journals Potencial económico de la palma aceitera (Elaeis guineensis Jacq)

2017 ◽  
Vol 28 (2) ◽  
pp. 523
Author(s):  
Juan Sierra Márquez ◽  
Lucellys Sierra Márquez ◽  
Jesus Olivero-Verbel
Keyword(s):  
Oil Palm ◽  
Animal Feed ◽  
Elaeis Guineensis ◽  
Raw Materials ◽  
Palm Kernel ◽  
Liquid Waste ◽  
Environmental Benefits ◽  
Special Importance ◽  
La Palma ◽  
Positive Balance

The objective of this research was to highlight the economic importance of the optimal use of products and byproducts of oil palm. In Colombia, productive crops per hectare can generate, over one year, an average of 3.14 tons of oil, and up to 21.68 t of solid and liquid waste when the plant is on a productive stage. These data allowed the researcher to estimate that more than nine million of t of solid and liquid waste was produced from the 450 131 ha present in 2014, in Colombia; the produced biomass was used to generate energy and steam, releasing carbon dioxide back again into the environment. These residues have great potential in many industries, some to be developed, therefore, it is of special importance to try to maximize the use of waste produced by oil palm production, to generate economic and environmental benefits. An example of this is the palm kernel cake, with a nutritional potential in animal feed, fiber in the biocompound industry, biomass and stipe in the timber industry, glycerol, biodiesel, and liquid effluents in the chemical and biotechnological industry. The use of these raw materials may help to establish a positive balance in the cultivation of this species of oil palm in the country. 

Making Oxalic Acid From Palm Oil Pelepah (Elaeis Guineensis) Through Nitric Acid Oxidation Reaction

2021 ◽  
Vol 1 (1) ◽  
pp. 10-14
Author(s):  
Ihwan Rahmadi
Keyword(s):  
Nitric Acid ◽  
Oxalic Acid ◽  
Palm Oil ◽  
Oil Palm ◽  
Elaeis Guineensis ◽  
Raw Materials ◽  
Nitric Acid Concentration ◽  
Acid Oxidation ◽  
Cellulose Conversion ◽  
Acid Yield

Palm oil palm is one of the solid waste produced by oil palm plantations every harvest. Chemical analysis of palm oil palm oil pellets showed that there are components of cellulose, hemiscellulose, and lignin that show that palm oil pellets have the opportunity to be further processed into useful and economically valuable products. Palm waste contains cellulose by 34.89%, hemiscellulose by 27.14%, and lignin by 19.87%. The analysis conducted on raw materials includes the analysis of water content and cellulose levels of palm oil palm oil. 46.6% and cellulose levels of 29.2%. In this study quantitative analysis was conducted in the form of cellulose conversion and oxalic acid yield. The largest cellulose conversion was obtained at the use of 70% nitric acid concentration and 80 minutes reaction time of 58.56%.

scholarly journals A Tale of Two Tiles: Characterization of Floor Tiles from the Nineteenth-Century Akko Tower Shipwreck (Israel)

Coatings ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1091
Author(s):  
Alexandra Inberg ◽  
Dana Ashkenazi ◽  
Yishai Feldman ◽  
Omri Dvir ◽  
Deborah Cvikel
Keyword(s):  
Secondary Ion Mass Spectrometry ◽  
Raw Materials ◽  
Type A ◽  
Raw Material ◽  
Brown Pigment ◽  
Blue Color ◽  
Type B ◽  
Yellow Color ◽  
Floor Tiles

Fragments of decorated floor tiles were retrieved from the Akko Tower shipwreck, Israel. Most tiles were made of bright brown fired clay with a white glaze decorated with colored stenciled motifs (Type A); and others consisted of a red-brown fired clay body, coated with a brown pigment covered with transparent brown glaze (Type B). This study aimed to characterize the two tile types; to reveal information concerning the manufacturing process; and to determine the origin of their raw material. A multidisciplinary approach was used, including light microscopy, SEM-EDS, electron probe microanalysis with wavelength-dispersive X-ray spectroscopy (EPMA-WDS), XRD, Raman spectroscopy, and time-of-flight secondary ion mass spectrometry (TOF-SIMS) analyses. The characterization of both tile types demonstrated the use of different raw materials. The Type A tiles were covered with tin-opacified majolica glaze and colored with various mixtures of pigments. The blue color was due to pigment rich in cobalt; the yellow color was due to Naples yellow and lead-tin yellow I minerals; and the green, orange, and brown colors were all prepared by mixing the Naples yellow pigment with different minerals. These majolica glaze tiles were probably manufactured in Sicily. The brown coating of the Type B tiles was due to pigment rich in lead and iron minerals. These tiles were produced with different manufacturing processes, and apparently made in France.

Sign in / Sign up

Export Citation Format

Share Document