scholarly journals An Investigation of the Mechanical Properties of Sintered Fly Ash Lightweight Aggregate Concrete (SFLWAC) with Steel Fibers

2018 ◽  
Vol 64 (1) ◽  
pp. 73-85 ◽  
Author(s):  
B. Ranjith Babu ◽  
R. Thenmozhi
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Mechanical Performance ◽  
Lightweight Aggregate ◽  
Steel Fibers ◽  
Lightweight Aggregate Concrete ◽  
Split Tensile Strength ◽  
Natural Aggregates ◽  
Ash Aggregates

Abstractthis study investigates the fresh and mechanical performance of concrete incorporating sintered fly ash lightweight aggregates (SFLWA) both with and without steel fibers. Comparative assessments of natural aggregates with sintered fly ash aggregates were evaluated. Mix design was obtained by the IS method for M30 grade concrete, and within the natural aggregates were replaced with 20%, 40%, and 60% amounts of SFLWA. The addition of SFLWA shows an increase in the workability of the concrete. Replacement with SFLWA increases with an increase in slump value, and decreases in strength parameters. Compressive strength of 42.6 MPa was achieved with a 40% replacement of SFLWA with steel fibers. The mechanical properties such as compressive strength, split tensile strength, flexural strength, elastic modulus, and structural efficiency of SFLWAC were examined, both with and without fibers. The incorporation of fibers drastically improved the mechanical properties of the mix.

scholarly journals Mechanical properties of concrete composed of sintered fly ash lightweight aggregate

2018 ◽  
Vol 195 ◽  
pp. 01008
Author(s):  
Puput Risdanareni ◽  
Januarti Jaya Ekaputri ◽  
Ike Maulidiyawati ◽  
Poppy Puspitasari
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Coarse Aggregate ◽  
Lightweight Aggregate ◽  
Effective Solution ◽  
Binding Agent ◽  
Split Tensile Strength ◽  
Bonded Method

This paper investigates the effect of sintered fly ash lightweight aggregate as coarse aggregate substitution on the mechanical properties of concrete. The lightweight aggregate (LWA) was produced using the cold bonded method and then sintered at a temperature of 900°C. An alkaliactivated system was applied as a binding agent of the LWA. Fly ash was used as precursor while sodium hydroxide and sodium silicate were employed as alkali activators. Three variations of the LWA dosage were performed, which were 0%, 50%, and 100 % of the volume of coarse aggregate in the concrete mixture. The mechanical properties of the concrete investigated in this research are the compressive strength and split tensile strength. The result showed that the mechanical properties of the concrete slightly decrease along with the increased dosage of the LWA in the mixture. However, employing sintered fly ash the LWA is proven as an effective solution in reducing the concrete density without sacrificing its strength.

Mechanical Properties of Mortar Modified with Cement Treated Tyre Crumb and Oil Palm Fruit Fibre

2015 ◽  
Vol 802 ◽  
pp. 225-230
Author(s):  
Farah Noor Abdul Aziz ◽  
Sani Mohammed Bida ◽  
Noor Azline Mohd Nasir ◽  
Nor Azizi Safiee ◽  
Mohd Saleh Jaafar
Keyword(s):  
Mechanical Properties ◽  
Oil Palm ◽  
Lightweight Aggregate ◽  
Lightweight Aggregate Concrete ◽  
Material Research ◽  
Split Tensile Strength ◽  
Palm Fruit ◽  
The Matrix ◽  
Waste Tyre ◽  
Mechanical Strengths

Addition or replacement of waste tyre in mortars and concretes in lightweight aggregate concrete composites are popular in concrete material research although the mechanical properties of the composite are reduced. Various research studies have been conducted in an effort to improve the mechanical properties of concretes and mortars containing waste tyre particles using chemicals and additives which lead to increase cost. This approach presents an economical and sustainable method, through adding oil palm fruit fibre (OPFF) at 0.5, 1%, and 1.5% by mass of cement content into the matrix and pre-treating the tyre crumb aggregate (0-40%) by volume with cement, in order to improve the properties of the composite. Mechanical properties including compressive strength, split tensile strength and flexural strength were measured on the mortar specimens. Results showed the addition of 0.5% OPFF in 10% treated tyre crumb mortar gives the best improvement in the mechanical strengths of mortar modified with treated tyre crumb.

Mechanical Properties of Fiber Reinforced Lightweight Aggregate Concrete

2011 ◽  
Vol 477 ◽  
pp. 274-279 ◽  
Author(s):  
Yi Xu ◽  
Lin Hua Jiang ◽  
Hong Qiang Chu ◽  
Lei Chen
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Water Hyacinth ◽  
Steel Fiber ◽  
Polypropylene Fiber ◽  
Lightweight Aggregate ◽  
Splitting Tensile Strength ◽  
Lightweight Aggregate Concrete ◽  
Fiber Types

In this study, the effects of fiber types on the mechanical properties of lightweight aggregate concretes were investigated. Three types of fibers, namely, polypropylene fiber, steel fiber and water hyacinth (Eichhornia crassipes) fiber, and two types of lightweight aggregates, namely, expanded polystyrene and ceramsite were used. The compressive strength and splitting tensile strength of concretes were tested. The results show that both the compressive strength and the splitting tensile strength were improved by adding a reasonable volume of steel fiber and polypropylene fiber into LWAC. The addition of water hyacinth fiber had little effect on the compressive strength of LWAC, while a little increase was observed in the splitting tensile strength.

scholarly journals Studies on Pumice Lightweight Aggregate Concrete with Quarry Dust Using Mathematical Modeling Aid of ACO Techniques

2016 ◽  
Vol 2016 ◽  
pp. 1-12 ◽  
Author(s):  
J. Rex ◽  
B. Kameshwari
Keyword(s):  
Mathematical Modeling ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Lightweight Aggregate ◽  
Optimization Techniques ◽  
Lightweight Aggregate Concrete ◽  
Split Tensile Strength ◽  
Rock Aggregate ◽  
Quarry Dust

The lightweight aggregate is an aggregate that weighs less than the usual rock aggregate and the quarry dust is a rock particle used in the concrete for the experimentation. The significant intention of the proposed technique is to frame a mathematical modeling with the aid of the optimization techniques. The mathematical modeling is done by minimizing the cost and time consumed in the case of extension of the real time experiment. The proposed mathematical modeling is utilized to predict four output parameters such as compressive strength (Mpa), split tensile strength (Mpa), flexural strength (Mpa), and deflection (in mm). Here, the modeling is carried out with three different optimization techniques like genetic algorithm (GA), particle swarm optimization (PSO), and ant colony optimization (ACO) with 80% of data from experiment utilized for the training and the remaining 20% for the validation. Finally, while testing, the error value is minimized and the performance obtained in the ACO for the parameters such as compressive strength, split tensile strength, flexural strength, and deflection is 91%, 98%, 87%, and 94% of predicted values, respectively, in the mathematical modeling.

scholarly journals Effect of Steel Fibers on Heat of Hydration and Mechanical Properties of Concrete Containing Fly Ash

2019 ◽  
Vol 38 (1) ◽  
pp. 83-94 ◽  
Author(s):  
Sajid Mehmood ◽  
Faheem Butt
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Construction Projects ◽  
Heat Of Hydration ◽  
Steel Fibers ◽  
Modulus Of Rupture ◽  
Consistent Increase ◽  
Lower Heat

This study investigated the effects of steel fibers on the fresh and hardened properties, and heat of hydration of concrete containing FA (Fly Ash). A total of 192 samples were cast comprising cubes, cylinders, and prisms, for six concrete mixes with varying contents of steel fibers by volume and a fixed content of FA i.e. 15% by weight of cement. The semi adiabatic setup was used to monitor temperature rise due to the heat of hydration in the concrete mixes for fourteen days. The use of FA increased workability, and decreased early compressive strength, tensile strength and heat of hydration of concrete. However, an increase in the compressive strength of FA concrete was observed by the addition of steel fibers up to 0.9% whereas a consistent increase in the splitting tensile strength and modulus of rupture was observed with the addition of the steel fibers from 0.4-1.8%. Further the test results showed that increasing steel fibers content decrease the evolution of heat due to hydration. It was concluded that the FA concrete with steel fibers can be used in precast industry and mass construction projects due to the improved mechanical properties and lower heat of hydration.

scholarly journals Mechanical and Microstructural Characterization of Quarry Rock Dust Incorporated Steel Fiber Reinforced Geopolymer Concrete and Residual Properties after Exposure to Elevated Temperatures

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6890
Author(s):  
Muhammad Ibraheem ◽  
Faheem Butt ◽  
Rana Muhammad Waqas ◽  
Khadim Hussain ◽  
Rana Faisal Tufail ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Weight Loss ◽  
Compressive Strength ◽  
Fly Ash ◽  
Mechanical Strength ◽  
Elevated Temperatures ◽  
Strength Properties ◽  
Steel Fibers ◽  
Geopolymer Concrete

The purpose of this research is to study the effects of quarry rock dust (QRD) and steel fibers (SF) inclusion on the fresh, mechanical, and microstructural properties of fly ash (FA) and ground granulated blast furnace slag (SG)-based geopolymer concrete (GPC) exposed to elevated temperatures. Such types of ternary mixes were prepared by blending waste materials from different industries, including QRD, SG, and FA, with alkaline activator solutions. The multiphysical models show that the inclusion of steel fibers and binders can enhance the mechanical properties of GPC. In this study, a total of 18 different mix proportions were designed with different proportions of QRD (0%, 5%, 10%, 15%, and 20%) and steel fibers (0.75% and 1.5%). The slag was replaced by different proportions of QRD in fly ash, and SG-based GPC mixes to study the effect of QRD incorporation. The mechanical properties of specimens, i.e., compressive strength, splitting tensile strength, and flexural strength, were determined by testing cubes, cylinders, and prisms, respectively, at different ages (7, 28, and 56 days). The specimens were also heated up to 800 °C to evaluate the resistance of specimens to elevated temperature in terms of residual compressive strength and weight loss. The test results showed that the mechanical strength of GPC mixes (without steel fibers) increased by 6–11%, with an increase in QRD content up to 15% at the age of 28 days. In contrast, more than 15% of QRD contents resulted in decreasing the mechanical strength properties. Incorporating steel fibers in a fraction of 0.75% by volume increased the compressive, tensile, and flexural strength of GPC mixes by 15%, 23%, and 34%, respectively. However, further addition of steel fibers at 1.5% by volume lowered the mechanical strength properties. The optimal mixture of QRD incorporated FA-SG-based GPC (QFS-GPC) was observed with 15% QRD and 0.75% steel fibers contents considering the performance in workability and mechanical properties. The results also showed that under elevated temperatures up to 800 °C, the weight loss of QFS-GPC specimens persistently increased with a consistent decrease in the residual compressive strength for increasing QRD content and temperature. Furthermore, the microstructure characterization of QRD blended GPC mixes were also carried out by performing scanning electron microscopy (SEM), X-ray diffraction (XRD), and energy dispersive spectroscopy (EDS).

scholarly journals Experimental Study of High-Strength Steel Fiber Lightweight Aggregate Concrete on Mechanical Properties and Toughness Index

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Yanxia Ye ◽  
Jilei Liu ◽  
Zhiyin Zhang ◽  
Zongbin Wang ◽  
Qiongwu Peng
Keyword(s):  
Mechanical Properties ◽  
Volume Content ◽  
High Strength Steel ◽  
Steel Fiber ◽  
Lightweight Aggregate ◽  
High Strength ◽  
Steel Fibers ◽  
Lightweight Aggregate Concrete ◽  
Aggregate Concrete ◽  
Toughness Index

In this paper, three different kinds of steel fibers, being micro (M), end-hooked (H), and corrugated (C), commonly used in engineering applications, are added to high-strength lightweight aggregate concrete (HLAC) to study the effects of steel fiber and volume content ratio of fiber on the compressive, splitting tensile, and flexural strength of HLAC. The range of steel fiber volume content fraction studied is 0.5% to 2.0%. The research shows that different types of steel fiber have different effects on the mechanical properties and toughness of HLAC. M steel fibers have the best reinforcing performance on the mechanical properties. The study also shows that the toughness of M steel fibers is the best with the same fiber content. The toughening effect of H and C steel fibers can only reach 2/3 and 1/2 of M steel fibers, respectively. At the end of this paper, the unified strength formula and toughness index of these three kinds of high-strength steel fiber lightweight aggregate concrete (HSLAC) with different fiber contents are given to provide a reference for engineering practice and design.

scholarly journals Effect of Additives on the Rheological and Mechanical Properties of Microfine-Cement-Based Grout

2019 ◽  
Vol 2019 ◽  
pp. 1-10
Author(s):  
Shuai Zhang ◽  
Weiguo Qiao ◽  
Yanzhi Li ◽  
Kai Xi ◽  
Pengcheng Chen
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Compressive Strength ◽  
Fly Ash ◽  
Mechanical Performance ◽  
Setting Time ◽  
Effect Of Additives ◽  
Microfine Cement ◽  
The Stability ◽  
Grouting Materials

Enhancement of the fluidity and mechanical performance of grouting materials has proven to be an effective method of seepage prevention in geotechnical engineering. In this research, a microfine-cement-based grout mixed with microfine fly ash (MFA), nano-CaCO3 (NC), and superplasticizer (SP) was designed to improve the rheological and mechanical properties of grouting materials, and the particle size distribution, fluidity, spreading ability, bleed capacity, setting time, and mechanical properties were studied. A water/solid (W/S) ratio of 1.2 was selected, and the contents of MFA, NC, and SP by mass of microfine cement (MC) were 0–40%, 0–2.0%, and 1.5%, respectively. The results showed that MFA and 1.5% SP improved the fluidity and spreading ability of fresh grouts, while prolonging the setting time. The addition of NC can increase the yield stress and plastic viscosity and decrease the fluidity and spreading ability; nevertheless, it obviously enhances the stability and shortens the setting time of grouts. The addition of MFA and 1.5% SP reduced the compressive strength of hardened grouts; however, the addition of NC improved the mechanical properties.

Mechanical Properties of Lightweight Alum Sludge Aggregate Concrete

2015 ◽  
Vol 754-755 ◽  
pp. 413-416 ◽  
Author(s):  
Nur Quraatu’ Aini Mohd Rajin ◽  
Roszilah Hamid
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Lightweight Concrete ◽  
Lightweight Aggregate ◽  
Lightweight Aggregate Concrete ◽  
Content Increase ◽  
Split Tensile Strength ◽  
Aggregate Concrete ◽  
Alum Sludge ◽  
Better Than

Disposal of alum sludge (AS) in such an economical and environmental friendly way is a major challenge that water treatment plants around the globe had to deal with. AS cannot be dumped into landfills as it contains heavy metals which are harmful to the environment. In this study, alum sludge is utilised as partial replacements (0, 5 and 10%) of natural granite coarse aggregate (by mass) to form a lightweight concrete. The water/cement ratio is 0.65. The water absorption of the alum sludge is 22.06%. The slump, density, compressive strength and split tensile strength of the lightweight alum sludge aggregate concrete (LASAC) reduce as the AS aggregate content increase. The density of the 10% AS aggregate concrete is 2185.3 kg/m3. The compressive strength reduced from 25.6 MPa to 16.7 MPa and 14.2 MPa at 0, 5 and 10% replacement of AS aggregate respectively. The 2.18 MPa tensile strength of the control concrete reduced to 1.53 MPa at 10% replacement of AS aggregate. But as for the flexural strength, it increases from 5.42 MPa for the control up to 5.55 MPa and 5.63 MPa for 5 and 10% replacement of AS aggregate respectively. Results show that strength of alum sludge lightweight aggregate concrete is better than lightweight crumb tyre aggregate concrete and is at par with oil palm coconut shell aggregate concrete.

Sign in / Sign up

Export Citation Format

Share Document