scholarly journals New Hybrid Turbochargers Solutions for Special Military Vehicles with Internal Combustion Engines

2020 ◽  
Vol 26 (3) ◽  
pp. 64-72
Author(s):  
Rareş-Lucian Chiriac ◽  
Anghel Chiru ◽  
Ovidiu Condrea
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Electrical Energy ◽  
Internal Combustion ◽  
Energy Performance ◽  
Exhaust Gas ◽  
Combustion Engines ◽  
Test Bed ◽  
Military Vehicles ◽  
The Military

AbstractThe internal combustion engines performance can be increase. The residual gases can be recovered through turbo charging systems because is an important reserve of exhaust gas energy, which can be capitalized. The turbo charging solution is one of the most popular technical solutions for increasing the energy performance of internal combustion engines. The solutions proposed for the theoretical and experimental research is the hybrid turbocharger. The hybrid turbocharger has a double function: to compress the fresh air and to generate electric energy for the vehicle. The compressed fresh air is compress by the rotor wheel of the compressor. The generator which produces the electrical energy is linearly coupled to the rotor on the compressor shaft outside zone. The electrical energy can be used for consumption of the military vehicles or can be stored in to the battery of the vehicle. The military vehicle must have a internal combustion engine or a hybrid engine equipped with a hybrid turbocharger. The article aim is to present the results of the hybrid turbocharger. The simulation was realised with the AMESim Software developed by Siemens. To simulate the exhaust gas energy was used a CIMAT test bed which can provides high pressure air.

scholarly journals Comparative Parameters Evaluation of Internal Combustion Engines Naturally Aspired and Supercharged With Hybrid Turbocharger

2020 ◽  
Author(s):  
Chiriac Rares ◽  
Anghel Chiru
Keyword(s):  
Internal Combustion Engine ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Energy Performance ◽  
Operating Efficiency ◽  
Combustion Engines ◽  
Exhaust Gases ◽  
Electric Generator ◽  
Technical Solutions

Abstract Internal combustion engines have an operating efficiency that can be exploited to increase their performance. Some of the waste gases can be recovered through technical solutions such as turbocharging. The turbocharging solution is one of the most popular technical solutions for increasing the energy performance of internal combustion engines. This requires an analysis of the energy balance of the internal combustion engine. This shows that there is a significant reserve of energy in the exhaust gases, which can be used to increase the engine efficiency. One solution is to use this energy to drive a turbine coupled with an electric generator. This article aims to present the result of the experimental research of the hybrid turbocharger, simulating and validating the new solutions for increasing the energy performance of internal combustion engines through hybrid turbochargers using a coupled electric generator. The simulations will be performed using AMESim software developed by Siemens to demonstrate through calculations the efficiency of new solutions, such as a hybrid turbocharger. The tests will be performed using an diesel internal combustion engine with a cylinder capacity of 1.9 liters which is also simulated with AMESim software. The residual exhaust gases of the internal combustion engine will drive the hybrid turbocharger turbine and generate electricity. Electricity can then be used for storage in the car battery or for consumption by the car's electrical system. The article also includes a comparative study between the power and torque of the naturally aspirated internal combustion engine equipped with a hybrid turbocharger.

New Technical Solution for Hybrid Turbochargers

2020 ◽  
Author(s):  
Chiriac Rares ◽  
Anghel Chiru
Keyword(s):  
Experimental Research ◽  
Internal Combustion Engines ◽  
Technical Information ◽  
Internal Combustion ◽  
Energy Performance ◽  
Technical Solution ◽  
Combustion Engines ◽  
Test Bed ◽  
Compressor Wheel ◽  
Technical Solutions

Abstract Internal combustion engines have an efficiency of operating which can be exploit to increase its performance. Part of the residual gases can be recovered through the technical solutions such as turbocharging. The turbocharging solution is one of the most popular technical solutions for increasing the energy performance of internal combustion engines. For the turbocharging process it is used a turbocharger. The turbocharger can contribute also with new technical solutions to increase the energy performance of the internal combustion engines. One of the solutions proposed for the theoretical and experimental research is the hybrid turbocharger, which has a double function, namely to compress the fresh air for the internal combustion engine, and to generate electric energy for the electric engine of the vehicle both for consumption other to be stored in batteries. This article aims is to present the result of the experimental research of the hybrid turbocharger, simulate and validate the new solutions for increasing the energy performance of internal combustion engines through hybrid turbochargers using a coupled electric generator. The simulations will be made using the AMESim Sofware developed by Siemens to demonstrate the efficiency of the new solutions such as a hybrid turbocharger through calculations. The tests will be carried out with the test bed CIMAT. CIMAT test bed is a machine which provides higt pressure air which simulate the combustion gases of an engine. The pourpose of the CIMAT test bed is to rotate the hybrid turbocharger turbine and also the compressor wheel. More technical information about the hybrid turbocharger test will be presented in the article and also constructive details. Based on the technical information and input data in the first phase it will be made an application for the simulation and validation of the prototype to demonstrate the great potential of the turbocharger to produce also green energy.

Calculation of Exhaust Gas Heat Produce for Ron 95, Ron97 and Vpower Racing Base Fuels use in Internal Combustion Engines

2017 ◽  
Vol 9 (3) ◽  
Author(s):  
I.B. Lias ◽  
H.B. Sharudin ◽  
M.H.B. Ismail ◽  
A.M.I.B. Mamat
Keyword(s):  
Heat Transfer ◽  
Heat Loss ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Exhaust System ◽  
Internal Combustion ◽  
Exhaust Gas ◽  
Combustion Engines ◽  
Exhaust Temperature ◽  
Different Types

The purpose of this study is to identify and analyse the calculation of exhaust gas heat produce (EGHP) in internal combustion engine (ICE) based on three types of fuel used specifically Petrol Ron 95, Petrol Ron 97 and Vpower racing base. The experimental test rig has used 1.6 CamPro Proton engine with 1561cc capacity and dynamometer. The calculation has used the basic formula of heat transfer equation and heat loss through the exhaust that included the mass flow rate of exhaust gas, specific heat of exhaust gas and temperature gradient. The exhaust temperature of ICE is generally in range from 400C to 600C and exhaust gas heat transfer affects the emissions burn-up in the exhaust system. This contributes significantly to the engine requirement. The experimental data was statistically analysed to identify the unknown parameter. High correlation of data variables can be determined based on the heat loss produced or EGHP. This also has significance by using different types of fuel in ICE.

scholarly journals Conception of gear ratios selection between the engine and the electric machine in the hybrid drive systems

2015 ◽  
Vol 160 (1) ◽  
pp. 56-61
Author(s):  
Kazimierz ROMANISZYN
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Engine Performance ◽  
Internal Combustion ◽  
Electric Machine ◽  
Exhaust Gas ◽  
Combustion Engines ◽  
Hybrid Drive ◽  
Drive Systems ◽  
Fuel Consumption And Emissions

Modern vehicles with hybrid combustion-electric drive systems are an important element in the strategy for reducing fuel consumption and emissions of exhaust gas components. Determinant of the use and development is to achieve substantial benefits in terms of classical powertrain vehicles equipped with internal combustion engines. This paper presents the concept of kinematic ratio selection between the engine and the electric machine. This concept is based on the analysis of the internal combustion engine load caused by the resistances of motion and the best possible assessment of the additional load caused by the operation of the generator. It is proposed that the energy transferred to the generator was taken in a most preferred area of the engine performance characteristics and generator by changing kinematic ratio between the engine and the generator. The described concept can also be used for the recovery of vehicles braking energy.

Design of a Method for Test Diagnostics of an Internal Combustion Engine Based on the Analysis of the Exhaust Gas Composition

2020 ◽  
Vol 67 (1) ◽  
pp. 104-110
Author(s):  
Aleksandr V. Gritsenko ◽  
Grigoriy N. Salimonenko ◽  
Maksim V. Nazarov
Keyword(s):  
Internal Combustion Engine ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Research Purpose ◽  
Exhaust Gas ◽  
Combustion Engines ◽  
Ignition System ◽  
Exhaust Gases ◽  
Diagnostic Parameters

The introduction of methods for timely diagnostics of internal combustion engines allows maintaining the environmental indicators of the car fleet at the highest level. (Research purpose) The research purpose is in increasing the reliability of diagnostics of internal combustion engines by using data obtained by selective sampling of exhaust gases. (Materials and methods) Informational, mathematical and experimental research methods, including methods for statistical processing of results and analysis of data obtained during experiments were used during the study. (Results and discussion) The main systems that affect the environmental performance of internal combustion engines has been identified: the fuel supply system, the ignition system and the exhaust gas neutralization system. The article describes a generalized mathematical model for calculating the characteristics of exhaust gases. Authors conducted operational tests on 35 internal combustion engines with justification of their number according to standard methods. The actual value of diagnostic parameters was processed into relative percentages for drawing a nomogram. A zero value has been set for the reference state of the elements specified by the manufacturer. (Conclusions) It was found that the dominant number of failures accounted for internal combustion engines, in detail: the ignition system produces 15-25 percent of failures, the power system produces 30-44 percent, the exhaust system produces 10-15 percent. It was found that for unambiguous identification of any combination of factors, it is necessary to have output values of at least three evaluation criteria. It was found that the most sensitive parameters for evaluating the technical condition of the three systems are: changes in the engine crankshaft speed, the parameters of exhaust gas toxicity, CO, CO2, CH, O2 when providing test modes (operation of the internal combustion engine on 1 cylinder at 20 and 40 percent of the throttle opening). The article describes designed a gasoline engine loader for the implementation of diagnostic modes and control of diagnostic parameters, that allows to create operating loads with an accuracy of 0.1 percent.

scholarly journals Environmental effect of molecular degradation of internal combustion engine exhaust gases

2021 ◽  
pp. 31-35
Author(s):  
В.В. Мурамович ◽  
В.Ю. Каминский ◽  
С.Н. Турусов
Keyword(s):  
Power Plants ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Ecological Problem ◽  
Exhaust Gas ◽  
Combustion Engines ◽  
Exhaust Gases ◽  
Advantages And Disadvantages ◽  
Toxic Components

Рассматривается экологическая проблема очистки отработавших газов углеводородных энергетических установок от токсичных компонентов. Показан состав основных токсичных компонентов, приведены значения энергии связи их молекул. Представлены существующие методы улучшения экологических характеристик двигателей внутреннего сгорания: рециркуляция отработавших газов, снижение степени сжатия, уменьшение угла опережения впрыска, добавление присадок к топливу и др. Перечислены их достоинства и недостатки. Предлагается новый метод – использование электромагнитных полей для очистки отработавших газов от токсичных компонентов. Выполнен оценочный расчет его эффективности. Показано, что применение устройств модификации в топливной системе двигателей внутреннего сгорания, а также в системе выпуска отработавших газов позволяет существенно снизить выбросы в окружающую среду вредных веществ, и, при этом, не требует принципиальных изменений в конструкции двигателей. Рабочий ресурс предлагаемых устройств электромагнитной обработки обусловлен применяемыми для их изготовления материалами. The ecological problem of cleaning the exhaust gases of hydrocarbon power plants from toxic components is considered. The composition of the main toxic components is shown; the values of the binding energy of their molecules are given. The existing methods of improving the environmental characteristics of internal combustion engines are presented: exhaust gas recirculation, reduction of the compression ratio, reduction of the injection advance angle, addition of fuel additives, etc. Their advantages and disadvantages are listed. A new method is proposed – the use of electromagnetic fields for cleaning exhaust gases from toxic components. An estimated calculation of its effectiveness is performed. It is shown that the use of modification devices in the fuel system of internal combustion engines, as well as in the exhaust gas system, can significantly reduce emissions of harmful substances into the environment, and, at the same time, does not require fundamental changes in the design of engines. The materials used for their manufacture determine the working life of the proposed electromagnetic processing devices.

scholarly journals Aging of engine oils and their influence on the wear of an internal combustion engine

2021 ◽  
Author(s):  
Marek Idzior
Keyword(s):  
Service Life ◽  
Internal Combustion Engine ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Exhaust Gas ◽  
Combustion Engines ◽  
Engine Oils ◽  
Base Oils ◽  
The Impact

New designs of internal combustion engines require the use of engine oils that can cope with more demanding conditions, primarily with greater loads and higher temperatures. The requirements of recent years have led to a wider use of modern base oils and specially designed additive packages. This avoids the formation of impurities and changes in viscosity as a result of shearing of the viscosity additives under high loads. The article discusses the important problem of oil aging during operation and the impact of this phenomenon on the operation of internal combustion engines. The influence of oil service life and its replacement on the emission of toxic exhaust gas components was discussed, and the results of research on the effect of oil service life on changes in their viscosity were presented.

scholarly journals Exhaust Gas Temperature Measurements in Diagnostics of Turbocharged Marine Internal Combustion Engines Part I Standard Measurements

2015 ◽  
Vol 22 (1) ◽  
pp. 47-54 ◽  
Author(s):  
Zbigniew Korczewski
Keyword(s):  
Internal Combustion Engines ◽  
Internal Combustion ◽  
Technical Condition ◽  
Temperature Measurements ◽  
Injection System ◽  
Exhaust Gas ◽  
Combustion Engines ◽  
Gas Temperature ◽  
Measuring Signal ◽  
Exhaust Gas Temperature

Abstract The article discusses the problem of diagnostic informativeness of exhaust gas temperature measurements in turbocharged marine internal combustion engines. Theoretical principles of the process of exhaust gas flow in turbocharger inlet channels are analysed in its dynamic and energetic aspects. Diagnostic parameters are defined which enable to formulate general evaluation of technical condition of the engine based on standard online measurements of the exhaust gas temperature. A proposal is made to extend the parametric methods of diagnosing workspaces in turbocharged marine engines by analysing time-histories of enthalpy changes of the exhaust gas flowing to the turbocompressor turbine. Such a time-history can be worked out based on dynamic measurements of the exhaust gas temperature, performed using a specially designed sheathed thermocouple. The first part of the article discusses possibilities to perform diagnostic inference about technical condition of a marine engine with pulse turbocharging system based on standard measurements of exhaust gas temperature in characteristic control cross-sections of its thermal and flow system. Selected metrological issues of online exhaust gas temperature measurements in those engines are discusses in detail, with special attention being focused on the observed disturbances and thermodynamic interpretation of the recorded measuring signal. Diagnostic informativeness of the exhaust gas temperature measurements performed in steady-state conditions of engine operation is analysed in the context of possible evaluations of technical condition of the engine workspaces, the injection system, and the fuel delivery process.

scholarly journals Assessment of thermodynamic cycle of internal combustion engine in terms of rightsizing

2019 ◽  
Vol 178 (3) ◽  
pp. 182-186
Author(s):  
Zbigniew SROKA ◽  
Maciej DWORACZYŃSKI
Keyword(s):  
Internal Combustion Engine ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Combustion Process ◽  
Thermodynamic Cycle ◽  
Internal Combustion ◽  
Research Problem ◽  
Combustion Engines ◽  
Operating Characteristics ◽  
Swept Volume

The modification of the downsizing trend of internal combustion engines towards rightsizing is a new challenge for constructors. The change in the displacement volume of internal combustion engines accompanying the rightsizing idea may in fact mean a reduction or increase of the defining swept volume change factors and thus may affect the change in the operating characteristics as a result of changes in combustion process parameters - a research problem described in this publication. Incidents of changes in the displacement volume were considered along with the change of the compression space and at the change of the geometric degree of compression. The new form of the mathematical dependence describing the efficiency of the thermodynamic cycle makes it possible to evaluate the opera-tion indicators of the internal combustion engine along with the implementation of the rightsizing idea. The work demonstrated the in-variance of cycle efficiency with different forms of rightsizing.

Sign in / Sign up

Export Citation Format

Share Document