scholarly journals Effects of annealing parameters on phase, structure and thermochromic properties of VO2 (M) derived from nanostructured VO2(B)

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Hamdi Muhyuddin Barra ◽  
Soo Kien Chen ◽  
Nizam Tamchek ◽  
Zainal Abidin Talib ◽  
Oon Jew Lee ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Phase Transition ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Sem Images ◽  
X Ray ◽  
Thermogravimetric Analyzer ◽  
Different Temperatures ◽  
Thermochromic Properties ◽  
Scanning Electron

Abstract Synthesis of thermochromic VO2 (M) was successfully done by annealing hydrothermally-prepared VO2 (B) at different temperatures and times. Conversion of the metastable VO2 (B) to the thermochromic VO2 polymorph was studied using thermogravimetric analyzer (TGA) under N2 atmosphere. Moreover, the phase and morphology of the synthesized samples were studied using X-ray diffraction (XRD) and field-emission scanning electron microscopy (FE-SEM), respectively. Accordingly, the XRD scans of all the annealed samples exhibited the presence of monoclinic VO2 (M), while the FE-SEM images of the samples showed the formation of nanorods and nanospheres, particularly those heated at high temperatures (650 °C and 700 °C). Meanwhile, differential scanning calorimetry (DSC) was used to measure the phase transition temperature (τc), hysteresis, and enthalpy of the prepared VO2. Based on these results, all samples displayed a τc of about 66 °C. However, the hysteresis was high for the samples annealed at lower temperatures (550 °C and 600 °C), while the enthalpy was very low for samples heated at lower annealing time (1.5 h and 1 h). These findings showed that crystallinity and nanostructure formation affected the thermochromic properties of the samples. In particular, the sample annealed at 650 °C showed better crystallinity and improved thermochromic behavior.

Effect of Cooling Rates on the Solidification and Microstructure of Rapidly Solidified Mg70.8Zn28Nd1.2 Quasicrystal Alloy

2017 ◽  
Vol 898 ◽  
pp. 246-253
Author(s):  
Xing Jing Ge ◽  
Xin Ying Teng ◽  
Shu Min Xu ◽  
Jin Yang Zhang
Keyword(s):  
Electron Microscopy ◽  
Phase Transition ◽  
Thermal Analysis ◽  
Energy Dispersive Spectrometer ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Cooling Rates ◽  
X Ray ◽  
Rapidly Solidified ◽  
Scanning Electron

The influence of cooling rates on the solidification and microstructure of rapidly solidified quasicrystal alloy Mg70.8Zn28Nd1.2(at.%) was investigated. The microstructure, phase constitution, phase transition and phase structure of the alloys were examined by means of scanning electron microscopy, x-ray diffraction, energy dispersive spectrometer, differential scanning calorimetry. The experimental results showed that the phase composition of as-cast Mg70.8Zn28Nd1.2 alloy includes quasicrystal I-phase and Mg7Zn3 phase. For the rapidly solidified alloy ribbons, when the speed is not higher than 400 r/min, the microstructure includes I-phase, Mg7Zn3 phase and α-Mg phase. When the speed is at the range of 400-2000r/min, the Mg7Zn3 phase disappears and only quasicrystal with α-Mg phase exist. With the increase of cooling rate, the grain size decreases and there are a large number of microcrystals in the microstructure. When the speed reaches higher than 2500 r/min, amorphous phase appeared. Differential thermal analysis showed that quasicrystal exist at about 340°C.

Research on compatibility and surface of high impact bio-based polyamide

2021 ◽  
pp. 095400832110055
Author(s):  
Yang Wang ◽  
Yuhui Zhang ◽  
Yuhan Xu ◽  
Xiucai Liu ◽  
Weihong Guo
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Crystallization Behavior ◽  
High Impact ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

The super-tough bio-based nylon was prepared by melt extrusion. In order to improve the compatibility between bio-based nylon and elastomer, the elastomer POE was grafted with maleic anhydride. Scanning Electron Microscopy (SEM) and Thermogravimetric Analysis (TGA) were used to study the compatibility and micro-distribution between super-tough bio-based nylon and toughened elastomers. The results of mechanical strength experiments show that the 20% content of POE-g-MAH has the best toughening effect. After toughening, the toughness of the super-tough nylon was significantly improved. The notched impact strength was 88 kJ/m2 increasing by 1700%, which was in line with the industrial super-tough nylon. X-ray Diffraction (XRD) and Differential Scanning Calorimetry (DSC) were used to study the crystallization behavior of bio-based PA56, and the effect of bio-based PA56 with high crystallinity on mechanical properties was analyzed from the microstructure.

scholarly journals Development of an Oxcarbazepine Solid Dispersion Using Skimmed Milk to Improve the Solubility and Dissolution Profile

2019 ◽  
Vol 11 (05) ◽  
Author(s):  
M. Shah ◽  
D. Patel
Keyword(s):  
Electron Microscopy ◽  
Solid Dispersion ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Infra Red ◽  
Crystalline Nature ◽  
Skimmed Milk ◽  
Scanning Electron

Oxcarbazepine has low solubility and low oral bioavailability, so it’s a challenge to formulate suitable dosage form. In this present investigation, to improve the dissolution rate and solubility, skimmed milk is used as a carrier. Physical mixers were prepared using various drugs to carrier ratio and spray drying technology was used to develop solid dispersion with the carrier. Various techniques were used to characterize the solid dispersion immediately after they were made which includes differential scanning calorimetry, scanning electron microscopy, fourier transform infra- red spectroscopy, X-ray diffraction and in-vitro dissolution profiles. The differential scanning calorimetry thermograms of raw drug indicated of its anhydrous crystalline nature. In thermograms of solid dispersion, the characteristic peak was absent suggesting the change from crystalline nature to amorphous form. X-ray diffraction confirmed those results. X-ray diffraction results of raw drug showed highly intense peak characteristic of its crystalline nature where solid dispersion showed less intense, more diffused peak indicating the change in crystalline form. Fourier transforms infra-red spectroscopy studies showed there was no interaction between drug and carrier. Scanning electron microscopy support the amorphous nature of mixer. The whole formulation showed distinct enhancement in the drug release behavior and solubility. The optimum oxcarbazepine to skimmed milk ratio 1:3 enhances the in-vitro drug release by 3.5 fold and also show distinct increase in solubility. It was concluded that for improvement of solubility of poorly water soluble oxcarbazepine, skimmed milk powder as a carrier can be utilize very well.

Microstructure and Properties of Nanosemicrystalline Si3N4 Ceramics with Doped Sintering Additives: Part II. Phase Transformation and Microstructural Control

1998 ◽  
Vol 13 (9) ◽  
pp. 2588-2596 ◽  
Author(s):  
K. H. Ryu ◽  
J-M. Yang
Keyword(s):  
Electron Microscopy ◽  
Pressureless Sintering ◽  
Particle Sizes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sintering Additives ◽  
Different Temperatures ◽  
Si3n4 Ceramics ◽  
Scanning Electron ◽  
Microstructural Control

The low temperature pressureless sintering of a nanosized Si3N4 powder with doped sintering additives was investigated. The microstructural evolution during sintering at different temperatures was analyzed using x-ray diffraction and scanning electron microscopy. The effect of using nanosized Si3N4 powder as a catalyst to accelerate the α→β–Si3N4 transformation of a commercial Si3N4 powder with larger particle sizes was also investigated. Finally, two stage sintering was used to study the feasibility of controlling the microstructure and the mechanical properties of the nanosized silicon nitride.

Preparation and Property of Al87Ce3Ni8.5Mn1.5 Nanophase Amorphous Composites

2011 ◽  
Vol 412 ◽  
pp. 263-266
Author(s):  
Hong Wei Zhang ◽  
Li Li Zhang ◽  
Feng Rui Zhai ◽  
Jia Jin Tian ◽  
Can Bang Zhang
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Single Phase ◽  
Volume Fraction ◽  
Material Structure ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Different Temperatures

The higher mechanical strength of Al87Ce3Ni8.5Mn1.5 nanophase amorphous composites has been obtained with two methods. The first nanophase amorphous composites are directly produced by the single roller spin quenching technology. The method taken for the second nanophase amorphous composites is at first to obtain amorphous single-phase alloy, followed by annealed at different temperatures .The formative condition, the microstructure, the particle size, the volume fraction of α-Al phase and microhardness of nanophase amorphous composites etc have been investigated and compared by X-ray diffraction (XRD) and transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). The microstructure of composites produced by the second method is higher than the former, the fabricated material structure of the system is more uniform and the process is easier to control.

Study of an Energetic-oxidant Co-crystal: Preparation, Characterisation, and Crystallisation Mechanism

2017 ◽  
Vol 67 (5) ◽  
pp. 510 ◽  
Author(s):  
Han Gao ◽  
Wei Jiang ◽  
Jie Liu ◽  
Gazi Hao ◽  
Lei Xiao ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Diffraction Spectrum ◽  
Solvent Evaporation Method ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

<p>An energetic co-crystal consisting of the most promising military explosive 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (CL-20) and the most well-known oxidant applied in propellants ammonium perchlorate has been prepared with a simple solvent evaporation method. Scanning electron microscopy revealed that the morphology of co-crystal differs greatly from each component. The X-ray diffraction spectrum, FTIR, Raman spectra, and differential scanning calorimetry characterisation further prove the formation of the co-crystal. The result of determination of hygroscopic rate indicated the hygroscopicity was effectively reduced. At last, the crystallisation mechanism has been discussed.</p>

Synthesis, Characterization and Magnetism of Nanosized Copper Ferrite

2008 ◽  
Vol 368-372 ◽  
pp. 604-606 ◽  
Author(s):  
Wei Zhong Lv ◽  
Zhong Kuang Luo ◽  
Bo Liu ◽  
Xiang Zhong Ren ◽  
Hong Hua Cai ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermal Analysis ◽  
Copper Ferrite ◽  
Sonochemical Method ◽  
Thermal Gravimetric ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Ft Ir ◽  
Scanning Electron

Copper ferrite powders were successfully synthesized by sonochemical method. The resultant powders were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), FT-IR, differential thermal analysis-thermal gravimetric (DTA-TG), differential scanning calorimetry (DSC) and VSM. The particle saturation magnetization (Ms) is 66 emu/g and an intrinsic coercive force (iHc) is 2100 Oe when the precursor calcined at 950 °C for 15 h.

Preparation of Tungsten-Doped VO2 (M) Nanoparticles through Sol-Gel Method and Hydrothermal Synthesis

2014 ◽  
Vol 881-883 ◽  
pp. 960-963 ◽  
Author(s):  
Ji Qi ◽  
Bin Zhao ◽  
Naisen Yu ◽  
Chen Niu ◽  
Guan Gran Sun
Keyword(s):  
Phase Transition ◽  
Vanadium Dioxide ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
New Process ◽  
Scanning Electron

A new process was developed for synthesizing tungsten-doped vanadium dioxide VO2(M) from ammonium metavanadate. The process includes obtaining V2O5by pyrolysing NH4VO3, doping tungsten in V2O5by sol-gel method, and reducing V2O5to VO2(M) with hydrazine by hydrothermal method. X-ray diffraction (XRD), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC) were applied to characterizing the product. The experimental results indicated that tungsten doped VO2(M) nanoparticles were successfully synthesized. The product VO2(M) presents mainly rod-like and block-like morphology. The phase transition temperature decreases with tungsten doped amount increasing, the phase transition takes place over the range from 36.23°C to 62.16°C and the largest enthalpy of the phase transition is 16.24J/g.

Hydriding Behaviour of Mg-C Nanocomposites

2003 ◽  
Vol 801 ◽  
Author(s):  
A. Bassetti ◽  
E. Bonetti ◽  
A. L. Fiorini ◽  
J. Grbovic ◽  
A. Montone ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Weight Ratio ◽  
Hydrogen Desorption ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Carbon Nanocomposites ◽  
X Ray ◽  
Scanning Electron

ABSTRACTMagnesium carbon nanocomposites for hydrogen storage have been synthesized by ball milling with different amount of benzene, acting as a lubricant. Their microstructure has been studied by X-ray diffraction and scanning electron microscopy, while the hydrogen desorption temperature has been tested by differential scanning calorimetry. Experimental results show that the microstructure after milling, the hydrogenation capabilities of the material and the reactivity with the air are related to the amount of additives. In particular the carbon to benzene ratio seems to play a major role. In fact, with an optimum value of carbon to benzene weight ratio of 1/6, the amount of carbon being 15 wt% of the milled mixture, a decomposition heat equal to 57% of pure MgH2 was measured, even after air manipulation of the sample.

Sign in / Sign up

Export Citation Format

Share Document