scholarly journals Sifat Mekanik Beton Serat Ijuk yang Terendam Air Laut

2019 ◽  
Vol 5 (2) ◽  
pp. 102
Author(s):  
Chaeril Anwar ◽  
Erniati Bachtiar ◽  
Nur Khaerat Nur
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fiber Length ◽  
Sea Water ◽  
Optimum Length ◽  
Normal Concrete ◽  
Split Tensile Strength ◽  
Fiber Concrete ◽  
Research Challenge

This research aims to determine the value of mechanical properties in fiber fibers which are submerged in seawater and to find out the optimum length of fiber fibers to the mechanical properties of fiber fibers which are submerged in sea water. The method used is an experimental method carried out in the laboratory by varying the length of the fibers, which is 25 mm; 50 mm; 75 mm; and 100 mm with 4% fiber addition. Tests of mechanical properties carried out in the form of compressive strength, split tensile strength, and flexural strength. The results of the research challenge the palm fiber-concrete that the longer the fibers used in the concrete, the mechanical properties decrease. Fiber concrete submerged in seawater has higher mechanical properties than normal concrete. Optimum fiber length length in fiber concrete from the results of this study is 25 mm.

scholarly journals Sifat Mekanis Beton Normal dengan Campuran Tepung Marmer

2018 ◽  
Vol 24 (1) ◽  
pp. 71
Author(s):  
Widodo Kushartomo ◽  
Dewi Permata Sari
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Cylindrical Specimen ◽  
Concrete Mixture ◽  
Beam Specimen ◽  
Test Results ◽  
Normal Concrete ◽  
Split Tensile Strength ◽  
Made In

This study is describe about the mechanical properties of normal concrete by adding of marble flour based on the mixed plan made. The compressive strength of the planned test object fc '20.0 and fc' 30.0 MPa was prepared by using the ACI method. The addition of marble flour in a concrete mixture varies from 0%, 5%, 10%, 15%, 20% and 25% to the weight of the cement used. Concrete test specimens were made in the form of cylinders 15.0 cm in diameter, 30.0 cm in height and made in the form of concrete beams measuring 15.0 cm x 15.0 cm x 75.0 cm, the type of mechanical testing performed in the form of compressive strength tests on cylindrical specimen, split tensile strength test on cylindrical specimen and flexure test on beam specimen. Curing is done by immersion technique at 25ºC and the test is done when the concrete is 28 days old. The test results show that the addition of marble flour to the normal concrete mixture can increase its mechanical properties by 26% for compressive strength, 24% for split tensile strength, and 17% for flexural strength. 

scholarly journals Behavior of Normal Concrete Reinforced with Fiber

2021 ◽  
Vol 4 (2) ◽  
pp. 123
Author(s):  
Prabowo Setiyawan
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fiber Length ◽  
Flexural Modulus ◽  
Compressive Test ◽  
Normal Concrete ◽  
Split Tensile Strength ◽  
Concrete Blocks ◽  
Concrete Materials ◽  
Average Compressive Strength

Concrete is a material with the ability to withstand a fairly high pressure, yet it has a low ability to withstand tension. To be utilized as a structure material, improvements need to be made to increase its tensile strength. Addition of fiber in the concrete mixture is recognized to be one among the existing methods to increase the tensile strength. Considering its high tensile strength, This study aimed to examine the compressive strength, the split tensile strength, the flexural and elastic modulus of the normal concrete with Menjalin fibers. The examination was conducted using a cylinder with the diameter of 15 cm and the height of 30 cm and a beam with the size of 15x15x60 cm. Fiber addition was 0.65% of the total concrete materials with various fiber lengths ranging from 2.5 cm, 5 cm, 7.5 cm to 10 cm. The experiment was made by the means of a concrete cylinder compressive test and a flexural test of unreinforced concrete blocks. Results of the study showed, at the age of 21 days, the highest average compressive strength value of 194.37 kg/cm2 and the split tensile strength of 30.43 kg/cm2 in the concrete with fiber of 5 cm long were obtained. The highest flexural modulus value of concrete occurred in the specimen with the fiber length of 7.5 cm (55.7 kg/cm2), while the highest elasticity of concrete occurred in the specimen with the fiber length of 5 cm (2.45x105 kg/cm2).

Influence the Carbonation Resistance and Mechanical Properties of Shotcrete by Accelerated Carbonation Test

2014 ◽  
Vol 1065-1069 ◽  
pp. 1985-1989
Author(s):  
Jia Bin Wang ◽  
Di Tao Niu ◽  
Rui Ma ◽  
Ze Long Mi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Steel Fiber ◽  
Splitting Tensile Strength ◽  
Construction Technology ◽  
Accelerated Carbonation ◽  
Carbonation Depth ◽  
Normal Concrete ◽  
Carbonation Resistance

In order to investigate the carbonation resistance of shotcrete and the mechanical properties after carbonation, the accelerated carbonation test was carried out. The results indicate that the carbonation resistance of shotcrete is superior to that of normal concrete. With the increasing of carbonation depth, compressive strength and splitting tensile strength of shotcrete grew rapidly. The admixing of steel fiber can further improve the carbonation resistance, reduce the carbonation rate, and increase the splitting tensile strength of shotcrete greatly. Besides, based on analyzing the effects of construction technology and steel fiber of concrete for the carbonation resistance, a carbonation depth model for shotcrete was established. Key words: shotcrete; carbonation; steel fiber; mechanical properties

Research on the Basic Mechanical Properties of Fly Ash Fiber Reinforced Concrete

2011 ◽  
Vol 261-263 ◽  
pp. 8-12
Author(s):  
Shu Shan Li ◽  
Ming Xiao Jia ◽  
Dan Ying Gao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Compressive Modulus ◽  
Fiber Reinforced Concrete ◽  
Cement Ratio ◽  
Influence Mechanism ◽  
Fiber Concrete ◽  
Early Strength

The basic mechanical properties of fly ash fiber concrete were tested. The influences to the compressive strength, splitting tensile strength and compressive modulus of elasticity of fiber concrete by water-cement ratio, dosage of fly ash and other factors were analyzed. The influence mechanism of fly ash to concrete is discussed. The results indicate that with the increase of the dosage of fly ash, the early strength of double-doped concrete is reduced, while the later strength of concrete was obviously increased.

scholarly journals Tests on workability and strength of high strength-flowable concrete containing PET waste fiber

2020 ◽  
Vol 7 (3) ◽  
pp. 115-139
Author(s):  
Sarkawt Karim ◽  
◽  
Azad Mohammed ◽  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fiber Length ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Time Increase ◽  
Fiber Volume ◽  
Split Tensile Strength ◽  
Pet Waste ◽  
Strength Tests

This study describes two workability tests, compressive strength and tensile strength tests of high strength flowable concrete containing plastic fiber prepared from polyethylene terephthalate (PET) waste bottles. For the high fluidity mix Vebe time and V-funnel time tests were carried out. Results show that there is a Vebe time increase with PET fiber addition to concrete being increased with increasing fiber volume and fiber length. V-funnel time was found to reduce when up to 0.75% fiber volume is added to concrete, followed by an increase for larger fiber volumes. When fiber length is increase, there is more time increase, but in general, V-funnel time increase was lower than that of Vebe time, indicating a different influence of PET fiber on the compatibility and flowability. The measured V-funnel time for all mixes was found to conform to the limits of European specifications on the flowability of self compacting concrete. Small descending in compressive strength was recorded for RPET fiber reinforced concrete that reached 15.74 % for 1.5 percent fiber content with 10 mm fiber length. Attractive results was recorded in split tensile strength of RPET fibrous samples which resulted in improvement up to 63.3 % for 1.5 percent of 40 mm fiber length content.

scholarly journals Investigation of the Effect of Addition Nano-papyrus Cane on the Mechanical Properties of Concrete

2021 ◽  
Vol 7 (2) ◽  
pp. 226-235
Author(s):  
Faisal K. Abdulhussein ◽  
Zahraa F. Jawad ◽  
Qais J. Frayah ◽  
ِAwham J. Salman
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Physical Properties ◽  
Construction Material ◽  
Dry Density ◽  
Split Tensile Strength ◽  
Maximum Enhancement ◽  
Concrete Mixtures ◽  
Traditional Construction

This paper investigates the effect of nano-papyrus cane ash as an additive on concretes’ mechanical and physical properties. Three types of concrete mixtures, 1:2:4, 1:1.5:3, and 1:1:2 were prepared for each mixture, nano-papyrus ash was added in five different dosages of 0.75, 1.5, 3, 4.5, and 6% by weight of cement; therefore, eighteen mixes would be studied in this work. Physical properties represented by dry density and slump were also measured for each mix. Moreover, to evaluate the mechanical properties development split tensile strength and compressive strength were obtained at age (7 and 28). Results manifested that the adding of nano ash developed the compressive strength and split tensile strength of concrete and the maximum enhancement recognized in the mixes with a content of 4.5% nano-papyrus in each studied mixture in this work. The slump test results indicated that the workability of concrete increased with adding nano-papyrus ash gradually with increasing nanoparticles' content. As well as, dry density was significant increased with nano-papyrus ratio; greater values were recorded in mixtures with 1.5-4.5% content of nano-papyrus. When comparing the concrete mixes used, it was found that the best results were obtained with 1:1:2 mixtures. This remarkable improvement in concrete properties considers the nano-papyrus is considered a cement economical and useful replacement for traditional construction material. Doi: 10.28991/cej-2021-03091649 Full Text: PDF

scholarly journals Experimental Studies on the Mechanical Properties of Loess Stabilized with Sodium Carboxymethyl Cellulose

2019 ◽  
Vol 2019 ◽  
pp. 1-8 ◽  
Author(s):  
Hongwang Ma ◽  
Qi Ma
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Carboxymethyl Cellulose ◽  
Experimental Studies ◽  
Loess Soil ◽  
Sodium Carboxymethyl Cellulose ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Split Tensile Strength

This research investigated the use of sodium carboxymethyl cellulose (CMC) as a reinforcement to improve mechanical properties of loess soil found in northwestern China. The mechanical properties of loess were determined by unconfined compressive strength and split tensile strength tests. Three different contents of CMC were adopted: 0.5%, 1.0%, and 1.5%. The results showed that utilizing CMC reduced the maximum dry density of the loess. The compressive strength, tensile strength, and Young’s modulus are enough to construct low-rise buildings when the CMC content exceeds 1.0%, based on existing standards. This research thus provides a prospective sustainability method for loess stabilization.

scholarly journals Experimental Investigation on Mechanical Properties of Hybrid Fiber Reinforced Quaternary Cement Concrete

2015 ◽  
Vol 10 (4) ◽  
pp. 155892501501000
Author(s):  
Ramesh Kanagavel ◽  
K. Arunachalam
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Impact Resistance ◽  
Polypropylene Fiber ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Cement Concrete ◽  
Split Tensile Strength ◽  
Polypropylene Fiber Reinforced Concrete

Mechanical properties of quaternary blending cement concrete reinforced with hybrid fibers are evaluated in this experimental study. The steel fibers were added at volume fractions of 0.5%, 1%, and 1.5 % and polypropylene fibers were added at 0.25% and 0.5% by weight of cementitious materials in the concrete mix individually and in hybrid form to determine the compressive strength, split tensile strength, flexural strength and impact resistance for all the mixes. The experimental results revealed that fiber addition improves the mechanical properties and also the ductility and energy absorption of the concrete. The results also demonstrate that the hybrid steel – polypropylene fiber reinforced concrete performs better in compressive strength, split tensile strength, flexural strength and impact resistance than mono steel and mono polypropylene fiber reinforced concrete.

scholarly journals Mechanical properties of concrete composed of sintered fly ash lightweight aggregate

2018 ◽  
Vol 195 ◽  
pp. 01008
Author(s):  
Puput Risdanareni ◽  
Januarti Jaya Ekaputri ◽  
Ike Maulidiyawati ◽  
Poppy Puspitasari
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Coarse Aggregate ◽  
Lightweight Aggregate ◽  
Effective Solution ◽  
Binding Agent ◽  
Split Tensile Strength ◽  
Bonded Method

This paper investigates the effect of sintered fly ash lightweight aggregate as coarse aggregate substitution on the mechanical properties of concrete. The lightweight aggregate (LWA) was produced using the cold bonded method and then sintered at a temperature of 900°C. An alkaliactivated system was applied as a binding agent of the LWA. Fly ash was used as precursor while sodium hydroxide and sodium silicate were employed as alkali activators. Three variations of the LWA dosage were performed, which were 0%, 50%, and 100 % of the volume of coarse aggregate in the concrete mixture. The mechanical properties of the concrete investigated in this research are the compressive strength and split tensile strength. The result showed that the mechanical properties of the concrete slightly decrease along with the increased dosage of the LWA in the mixture. However, employing sintered fly ash the LWA is proven as an effective solution in reducing the concrete density without sacrificing its strength.

scholarly journals An Integrated Evaluation of Manufactured Sand and Metakaolin Impacts on Concrete Properties

2019 ◽  
Vol 8 (12) ◽  
pp. 188-192
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Normal Concrete ◽  
Split Tensile Strength ◽  
Natural Sand ◽  
Manufactured Sand ◽  
Concrete Properties ◽  
Concrete Mix

This paper deals with M25 Concrete mix in which replacing Natural Sand by the Manufacturing Sand of 35% and 65% at Cement by Metakaolin of 0, 5, 10, 15 and 20 percentages is compared with concrete had cement with Metakaolin at different percentages without replacement of natural sand .Workability is determined for Concrete and Cylindrical specimens of 150mm*300mm of size are casted to test Concrete properties such as Split Tensile strength(STS) and Compressive Strength(CS) of Concrete. These specimens are placed under curing of 7days, 28days and 60days; after that time placed under testing and compared the results with Normal Concrete.

Sign in / Sign up

Export Citation Format

Share Document