scholarly journals Taguchi parametric study on the radial and tangential cutting forces in Dry High Speed Machining (DHSM)

10.30544/472 ◽  
2020 ◽  
Vol 26 (3) ◽  
pp. 303-316
Author(s):  
M. Hatami ◽  
H. Safari
Keyword(s):  
Titanium Alloy ◽  
Cutting Force ◽  
Feed Rate ◽  
Parametric Study ◽  
Cutting Forces ◽  
High Speed ◽  
Cutting Tools ◽  
High Speed Machining ◽  
Cutting Speeds

In this paper, L8 Taguchi array is applied to find the most important parameters effects on the radial and tangential cutting forces of a Ti–6Al-4V ELI titanium alloy in dry high speed machining (DHSM). The experiments are performed in four cutting speeds of 150, 200, 250, and 300 m/min and two feed rates of 0.03 and 0.06 mm/rev. Also, two cutting tools in types of XOMX090308TR-ME06 of uncoated (H25) and TiAlN+TiN coated (F40M) are used. Results confirm that to minimize the resultant cutting force and radial cutting force, utilizing the lower feed rate and higher cutting speeds were considered as the best levels of factors to reach to its goal.

Cutting Temperature and Cutting Forces Investigation Based on the Taguchi Design Method when High-Speed Milling of Titanium Matrix Composites with PCD Tool

2016 ◽  
Vol 836-837 ◽  
pp. 168-174 ◽  
Author(s):  
Ying Fei Ge ◽  
Hai Xiang Huan ◽  
Jiu Hua Xu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Volume Fraction ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling tests were performed on vol. (5%-8%) TiCp/TC4 composite in the speed range of 50-250 m/min using PCD tools to nvestigate the cutting temperature and the cutting forces. The results showed that radial depth of cut and cutting speed were the two significant influences that affected the cutting forces based on the Taguchi prediction. Increasing radial depth of cut and feed rate will increase the cutting force while increasing cutting speed will decrease the cutting force. Cutting force increased less than 5% when the reinforcement volume fraction in the composites increased from 0% to 8%. Radial depth of cut was the only significant influence factor on the cutting temperature. Cutting temperature increased with the increasing radial depth of cut, feed rate or cutting speed. The cutting temperature for the titanium composites was 40-90 °C higher than that for the TC4 matrix. However, the cutting temperature decreased by 4% when the reinforcement's volume fraction increased from 5% to 8%.

The effect of monolayer TiCN-, AlTiN-, TiAlN-and two layers TiCN + TiN- and AlTiN + TiN-coated cutting tools on tool wear, cutting force, surface roughness and chip morphology during high-speed milling of Ti6Al4V titanium alloy

2016 ◽  
Vol 232 (7) ◽  
pp. 1273-1286 ◽  
Author(s):  
Emel Kuram
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Tool Wear ◽  
Cutting Force ◽  
High Speed ◽  
Cutting Tools ◽  
Chip Morphology ◽  
High Speed Milling ◽  
Ti6al4v Titanium Alloy ◽  
Coated Carbide

Tool coatings can improve the machinability performance of difficult-to-cut materials such as titanium alloys. Therefore, in the current work, high-speed milling of Ti6Al4V titanium alloy was carried out to determine the performance of various coated cutting tools. Five types of coated carbide inserts – monolayer TiCN, AlTiN, TiAlN and two layers TiCN + TiN and AlTiN + TiN, which were deposited by physical vapour deposition – were employed in the experiments. Tool wear, cutting force, surface roughness and chip morphology were evaluated and compared for different coated tools. To understand the tool wear modes and mechanisms, detailed scanning electron microscope analysis combined with energy dispersive X-ray of the worn inserts were conducted. Abrasion, adhesion, chipping and mechanical crack on flank face and coating delamination, adhesion and crater wear on rake face were observed during high-speed milling of Ti6Al4V titanium alloy. In terms of tool wear, the lowest value was obtained with TiCN-coated insert. It was also found that at the beginning of the machining pass TiAlN-coated insert and at the end of machining TiCN-coated insert gave the lowest cutting force and surface roughness values. No change in chip morphology was observed with different coated inserts.

The Application of FEA in High-Speed Cutting Tool

2011 ◽  
Vol 314-316 ◽  
pp. 1258-1261
Author(s):  
Lian Qing Ji ◽  
Kun Liu
Keyword(s):  
Titanium Alloy ◽  
Cutting Force ◽  
High Speed ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Temperature ◽  
Material Model ◽  
Friction Model ◽  
High Speed Cutting ◽  
Key Technologies

The history and application of the FEA are briefly presented in this paper. Several key technologies such as the building of material model, the establishment of the chip - tool friction model as well as meshing are described. Taking the high-speed cutting of titanium alloy (Ti - 10V - 2Fe - 3Al) as an example , reasonable cutting tools parameters are determined by simulating the influences of cutting temperature, cutting force on the tools parameters using FEA.

Ultra-High-Speed Machining: A Review and an Analysis of Cutting Forces

1973 ◽  
Vol 187 (1) ◽  
pp. 625-634 ◽  
Author(s):  
G. Arndt
Keyword(s):  
Cutting Forces ◽  
High Speed ◽  
Physical Factors ◽  
High Speed Machining ◽  
Work Related ◽  
Rate Dependent ◽  
High Speeds ◽  
Ultra High Speed ◽  
Very High ◽  
Cutting Speeds

As part of the search for a new cutting mechanism, a few largely empirical investigations into ultra-high-speed machining (velocity greater than 500 ft/s) have been performed in the past. A comprehensive review of this and other work related to machining at very high cutting speeds is presented and the physical factors predominating in UHSM are discussed. As a consequence of this a new theory of cutting forces at ultra-high speeds is presented, based on inertia and temperature effects, adiabatic shear, and strain-rate dependent yield stress. This theory shows that workpiece properties greatly influence force behaviour, the latter determining the feasibility of machining at ultra-high speeds.

Cutting Force and Tool Deflection Predictions for High Speed Machining of Hard to Cut Material

2010 ◽  
Vol 154-155 ◽  
pp. 1157-1164 ◽  
Author(s):  
Jinn Jong Sheu ◽  
Dong Mei Xu ◽  
Chin Wei Liu
Keyword(s):  
Cutting Force ◽  
Cutting Forces ◽  
High Speed ◽  
Force Model ◽  
Beam Model ◽  
High Speed Machining ◽  
Tool Deflection ◽  
Machining Center ◽  
Helical Angle ◽  
Cutting Experiment

The dimension accuracy and the too life are the major issues of the machining of hard-to-cut materials. To fulfill the requirements of accuracy and tool life needs not only well planning of cutting path but also the proper cutting conditions of cutters. The vibration and deflection of cutters caused by poor selection of cutting conditions can be predicted using models of cutting force and tool deflection. In this paper, a cutting force model considering the effect of tool helical angle and a cantilever beam model of tool deflection were proposed for the high speed machining of hard-to-cut material SKD11. The shearing force, the plowing forces, and the helical angle of cutters are considered in the elemental force model. The material of workpiece, SKD11, studied in this paper is commonly used for the die and mold industries. The cutting constants of the proposed force model are determined via the cutting experiments carried out on a high speed machining center. A dynamometer and a high frequency data acquisition system were used to measure the x-, y-, and z-direction cutting forces. The obtained cutting constants were used to predict the cutting forces and compared with the results obtained from the cutting experiment of verification using cutters with different helical angles. The theoretical and the experimental cutting forces in the x-, y-, and z- direction are in good agreement using flat cutters with 30 and 45 degrees of helical angle. The dimension deviations of the cut surface in the cutting experiment case of tool deflection were measured using a touch probe and an infrared receiver installed on the machining center. The measured average dimension deviation, 0.163mm, is close to the predicted tool deflection, 0.153mm, using the proposed cantilever beam model. The comparisons of the cutting forces and the average of the cut surface dimension deviation are in good agreement and verify the proposed cutting force and the tool deflection models are feasible and useful.

Evaluation of the cutting forces, the surface roughness, and the tool wear characteristics during machining of cobalt-based superalloy Haynes 188 with ceramic cutting tool

2021 ◽  
pp. 095440892110480
Author(s):  
Abdullah Altin
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Cutting Forces ◽  
Cutting Tool ◽  
Signal To Noise Ratio ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Signal To Noise ◽  
Ceramic Cutting Tool ◽  
Cutting Speeds

In this research, we had studied the sensitivity for machining of cobalt-based superalloy Haynes 188 with ceramic cutting tool. The investigation had focused on the effects of the cutting speed, on the cutting forces, and on the surface roughness based on Taguchi’s experimental design. The effects of machining parameters were determined using Taguchi’s L27 orthogonal array. The signal-to-noise ratio was calculated for the average of surface roughness and the cutting forces, and the smaller were used to determine the optimal cutting conditions. The analysis of variance and the signal-to-noise ratio had effects on the parameters on both surface roughness and cutting. Three different types of cutting tools had been used in the experiment, namely KYON 4300, KYS 25, and KYS 30. The cutting force of Fz was considered to be the main cutting force. Depending on the material which had been used as cutting tool, the Fz had the lowest cutting speed and the lowest surface roughness with the KYS25 ceramic tool. The cutting force and the surface roughness of KYON 4300 cutting tool had shown better performance than other cutting tools. The flank wear and notch were found to be more effective in the experiments. The long chips were removed at low and medium cutting speeds, while the sawdust with one edge and narrow pitch at high cutting speeds was obtained.

Ultra-High-Speed Machining: A Review and an Analysis of Cutting Forces

1973 ◽  
Vol 187 (1) ◽  
pp. 625-634 ◽  
Author(s):  
G. Arndt
Keyword(s):  
Cutting Forces ◽  
High Speed ◽  
Physical Factors ◽  
High Speed Machining ◽  
Work Related ◽  
Rate Dependent ◽  
High Speeds ◽  
Ultra High Speed ◽  
Very High ◽  
Cutting Speeds

As part of the search for a new cutting mechanism, a few largely empirical investigations into ultra-high-speed machining (velocity greater than 500 ft/s) have been performed in the past. A comprehensive review of this and other work related to machining at very high cutting speeds is presented and the physical factors predominating in UHSM are discussed. As a consequence of this a new theory of cutting forces at ultra-high speeds is presented, based on inertia and temperature effects, adiabatic shear, and strain-rate dependent yield stress. This theory shows that workpiece properties greatly influence force behaviour, the latter determining the feasibility of machining at ultra-high speeds.

scholarly journals Drilling Burr Minimization by Changing Drill Geometry

Materials ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3207
Author(s):  
Emilia Franczyk ◽  
Łukasz Ślusarczyk ◽  
Wojciech Zębala
Keyword(s):  
Titanium Alloy ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
Complete Elimination ◽  
Positive Correlation ◽  
Optimal Geometry ◽  
Burr Size ◽  
Specific Length

This article presents an attempt to solve the problem of the formation of burrs and drilling caps in the process of drilling in difficult-to-cut materials, specifically in the titanium alloy Ti-6Al-4V. In order to eliminate these phenomena, a chamfer of specific length and angle was made on FANAR drill’s margin. Taguchi and ANOVA methods were used to plan and analyze the experiment aimed at determining the optimal geometry of the modified drill. Chamfer with a length of 2 mm and an angle of 10° was selected. In the next stage of research, the values of cutting forces and burr heights obtained during drilling with the original and modified drill were compared for three different feed rate values. It turned out that the introduced changes significantly reduced both the axial cutting force (22–23%) and the height of burrs (10–22%) and caused the complete elimination of the presence of drilling caps. Additionally, a positive correlation between the cutting force and the burr size was found.

scholarly journals Impact of Cutting Forces and Chip Microstructure in High Speed Machining of Carbon Fiber – Epoxy Composite Tube

2017 ◽  
Vol 62 (3) ◽  
pp. 1771-1777 ◽  
Author(s):  
Y. Allwin Roy ◽  
K. Gobivel ◽  
K.S. Vijay Sekar ◽  
S. Suresh Kumar
Keyword(s):  
Carbon Fiber ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Cutting Speed ◽  
Weight Ratio ◽  
Cutting Parameters ◽  
High Speed Machining ◽  
The Impact ◽  
Thrust Forces

AbstractCarbon fiber reinforced polymeric (CFRP) composite materials are widely used in aerospace, automobile and biomedical industries due to their high strength to weight ratio, corrosion resistance and durability. High speed machining (HSM) of CFRP material is needed to study the impact of cutting parameters on cutting forces and chip microstructure which offer vital inputs to the machinability and deformation characteristics of the material. In this work, the orthogonal machining of CFRP was conducted by varying the cutting parameters such as cutting speed and feed rate at high cutting speed/feed rate ranges up to 346 m/min/ 0.446 mm/rev. The impact of the cutting parameters on cutting forces (principal cutting, feed and thrust forces) and chip microstructure were analyzed. A significant impact on thrust forces and chip segmentation pattern was seen at higher feed rates and low cutting speeds.

scholarly journals Finite Element Modeling of the Effect of Tool Rake Angle on Cutting Force and Tool Temperature during High Speed Machining of AISI 1045 Steel

2014 ◽  
Vol 939 ◽  
pp. 194-200
Author(s):  
Shamsuddin Sulaiman ◽  
Mohd K.A. Ariffin ◽  
A. Roshan
Keyword(s):  
Finite Element ◽  
Cutting Force ◽  
High Speed ◽  
Metal Cutting ◽  
Rake Angle ◽  
Cutting Process ◽  
High Speed Machining ◽  
Tool Temperature ◽  
Aisi 1045 ◽  
Cutting Speeds

A finite element model (FEM) of an orthogonal metal-cutting process is used to study the influence of tool rake angle on the cutting force and tool temperature. The model involves Johnson-Cook material model and Coulomb’s friction law. A tool rake angle ranging from 0° to 20° and a cutting speed ranging from 300 to 600 m/min were considered in this simulation. The results of this simulation work are consistent optimum tool rake angle for high speed machining (HSM) of AISI 1045 medium carbon steel. It was observed that there was a suitable rake angle between 10° and 18° for cutting speeds of 300 and 433 m/min where cutting force and temperature were lowest. However, there was not optimum rake angle for cutting speeds of 550 and 600 m/min. This paper can contribute in optimization of cutting tool for metal cutting process.

Sign in / Sign up

Export Citation Format

Share Document