scholarly journals Preparation and Characterization of Epoxidised and Acrylated Styrene/Isoprene/Styrene (SIS) Triblock Block Copolymer Based Nanocomposites

2013 ◽  
Vol 28 ◽  
pp. 84-88 ◽  
Author(s):  
Santosh Khanal ◽  
Alina Shakya ◽  
Goerg H. Michler ◽  
Boulos Youssef ◽  
Jean M. Saiter ◽  
...  
Keyword(s):  
Block Copolymer ◽  
Chemical Society ◽  
Performic Acid ◽  
Casting Method ◽  
Immiscible Polymers ◽  
Transmission Electron ◽  
Boehmite Nanoparticles ◽  
Solution Casting Method

In this work, a commercially available Styrene-Isoprene-Styrene (SIS)triblock copolymer was modified into epoxidised version (ESIS)using performic acid generated in situ from hydrogen peroxide and formic acid. The epoxidised sample was further acrylated to prepare acrylated version (ASIS). The nanocomposites of each sample (SIS, ESIS and ASIS) were prepared using boehmite nanoparticles as filler by solution casting method. The polymers were characterized by Fourier Transform Infrared (FTIR) spectroscopy and transmission electron microscopy (TEM). TEM investigations revealed that that the epoxidation of the diene block enhanced the dispersion of the nanofiller in the polymer matrix while the segregation of the nanoparticles towards the interface of the immiscible polymers was observed in the acrylated block copolymer based nanocomposite. DOI: http://dx.doi.org/10.3126/jncs.v28i0.8112 Journal of Nepal Chemical Society Vol. 28, 2011 Page: 84-88 Uploaded Date: May 24, 2013

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

1973 ◽  
Vol 31 ◽  
pp. 132-133 ◽  
Author(s):  
R. E. Herfert
Keyword(s):  
Surface Characterization ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Depth Of Penetration ◽  
X Ray ◽  
The Past ◽  
Transmission Electron ◽  
Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

scholarly journals Fabrication and characterization of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) modified with nano-montmorillonite biocomposite

e-Polymers ◽  
2020 ◽  
Vol 21 (1) ◽  
pp. 038-046
Author(s):  
Xu Yan ◽  
Wanru Zhou ◽  
Xiaojun Ma ◽  
Binqing Sun
Keyword(s):  
Thermal Stability ◽  
Oxygen Permeability ◽  
Water Vapor Permeability ◽  
Barrier Properties ◽  
Nucleating Agent ◽  
Vapor Permeability ◽  
Casting Method ◽  
Increasing Trend ◽  
Solution Casting Method

Abstract In this study, a poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) modified with nano-montmorillonite biocomposite (MMT/PHBH) was fabricated by solution-casting method. The results showed that the addition of MMT increased the crystallinity and the number of spherulites, which indicated that MMT was an effective nucleating agent for PHBH. The maximum decomposition peak of the biocomposites moved to a high temperature and residue presented an increasing trend. The biocomposites showed the best thermal stability at 1 wt% MMT. Compared with PHBH, 182.5% and 111.2% improvement in elastic modulus and tensile strength were obtained, respectively. Moreover, the oxygen permeability coefficient and the water vapor permeability of MMT/PHBH biocomposites decreased by 43.9% and 6.9%, respectively. It was also found that the simultaneous enhancements on the crystallizing, thermal stability, mechanical, and barrier properties of biocomposites were mainly caused by the formation of intercalated structure between PHBH and MMT.

Fabrication and In Situ Transmission Electron Microscope Characterization of Free-Standing Graphene Nanoribbon Devices

ACS Nano ◽  
2016 ◽  
Vol 10 (1) ◽  
pp. 1475-1480 ◽  
Author(s):  
Qing Wang ◽  
Ryo Kitaura ◽  
Shoji Suzuki ◽  
Yuhei Miyauchi ◽  
Kazunari Matsuda ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Graphene Nanoribbon ◽  
Free Standing ◽  
Transmission Electron

scholarly journals Hydrogenative Cyclization of Levulinic Acid to γ-Valerolactone with Methanol and Ni-Fe Bimetallic Catalysts

Catalysts ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1096
Author(s):  
Ligang Luo ◽  
Xiao Han ◽  
Qin Zeng
Keyword(s):  
Photoelectron Spectroscopy ◽  
Levulinic Acid ◽  
Hydrogen Donor ◽  
Effect Of Temperature ◽  
X Ray ◽  
Transmission Electron ◽  
Ft Ir ◽  
Temperature Programmed

A series of Ni-Fe/SBA-15 catalysts was prepared and tested for the catalytic hydrogenation of levulinic acid to γ-valerolactone, adopting methanol as the only hydrogen donor, and investigating the synergism between Fe and Ni, both supported on SBA-15, towards this reaction. The characterization of the synthesized catalysts was carried out by XRD (X-ray powder diffraction), TEM (transmission electron microscopy), H2-TPD (hydrogen temperature-programmed desorption), XPS (X-ray photoelectron spectroscopy), and in situ FT-IR (Fourier transform–infrared spectroscopy) techniques. H2-TPD and XPS results have shown that electron transfer occurs from Fe to Ni, which is helpful both for the activation of the C=O bond and for the dissociative activation of H2 molecules, also in agreement with the results of the in situ FT-IR spectroscopy. The effect of temperature and reaction time on γ-valerolactone production was also investigated, identifying the best reaction conditions at 200 °C and 180 min, allowing for the complete conversion of levulinic acid and the complete selectivity to γ-valerolactone. Moreover, methanol was identified as an efficient hydrogen donor, if used in combination with the Ni-Fe/SBA-15 catalyst. The obtained results are promising, especially if compared with those obtained with the traditional and more expensive molecular hydrogen and noble-based catalysts.

Growth and Characterization of Cobalt-filled Carbon Nanotubes Prepared by a Simple Catalytic Method

2003 ◽  
Vol 776 ◽  
Author(s):  
Xicheng Ma ◽  
Yuanhua Cai ◽  
Xia Li ◽  
Ning Lun ◽  
Shulin Wen
Keyword(s):  
Carbon Nanotubes ◽  
Metallic Nanoparticles ◽  
Low Cost ◽  
Catalytic Method ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
High Resolution Tem ◽  
One Step

AbstractHigh-quality cobalt-filled carbon nanotubes (CNTs) were prepared in situ in the decomposition of benzene over Co/silica-gel nano-scale catalysts. Unlike the previous reports, the catalysts needn't be pre-reduced prior to the forming of Co-filled CNTs, thus the advantage of this method is that Co-filled CNTs can be produced in one step, at a relatively low cost. Transmission electron microscopy (TEM) investigation showed that the products contained abundance of CNTs and most of them were filled with metallic nanoparticles or nanorods. High-resolution TEM (HRTEM), selected area electron diffraction (SAED) patterns and energy dispersive X-ray spectroscopy (EDS) confirmed the presence of Co inside the nanotubes. The encapsulated Co was further identified always as high temperature alpha-Co phase with fcc structure, which frequently consists of twinned boundaries and stacking faults. Based on the experimental results, a possible growth mechanism of the Co-filled CNTs was proposed.

In situ characterization of kinetics and mass transport of PbSe nanowire growth via LS and VLS mechanisms

Nanoscale ◽  
2019 ◽  
Vol 11 (13) ◽  
pp. 5874-5878 ◽  
Author(s):  
Miao Song ◽  
Jaewon Lee ◽  
Bin Wang ◽  
Benjamin A. Legg ◽  
Shenyang Hu ◽  
...  
Keyword(s):  
Mass Transport ◽  
Nucleation And Growth ◽  
In Situ Characterization ◽  
Transport Pathways ◽  
Structure Control ◽  
Transmission Electron ◽  
Gas Heating ◽  
Dependent Mass

We grew binary PbSe nanowires in an in situ gas-heating cell in a transmission electron microscope and elucidated species dependent mass transport pathways and correlations among supersaturation, nucleation, and growth kinetics, enabling structure control.

scholarly journals In Situ IR Characterization of CO Interacting with Rh Nanoparticles Obtained by Calcination and Reduction of Hydrotalcite-Type Precursors

2011 ◽  
Vol 2011 ◽  
pp. 1-8 ◽  
Author(s):  
F. Basile ◽  
I. Bersani ◽  
P. Del Gallo ◽  
S. Fiorilli ◽  
G. Fornasari ◽  
...  
Keyword(s):  
Crystal Size ◽  
Liquid Nitrogen Temperature ◽  
Transmission Electron ◽  
In Situ Ir ◽  
Ft Ir ◽  
Co Disproportionation ◽  
Ft Ir Spectroscopy

Supported Rh nanoparticles obtained by reduction in hydrogen of severely calcined Rh/Mg/Al hydrotalcite-type (HT) phases have been characterized by FT-IR spectroscopy of adsorbed CO [both at room temperature (r.t.) and nominal liquid nitrogen temperature] and Transmission Electron Microscopy (TEM). The effect of reducing temperature has been investigated, showing that Rh crystal size increases from 1.4 nm to 1.8 nm when the reduction temperature increases from 750°C to 950°C. The crystal growth favours the formation of bridged CO species and linear monocarbonyl species with respect to gem-dicarbonyl species; when CO adsorbs at r.t., CO disproportionation occurs on Rh and it accompanies the formation of RhI(CO)2. The role of interlayer anions in the HT precursors to affect the properties of the final materials has been also investigated considering samples prepared from silicate-instead of carbonate-containing precursors. In this case, formation of RhI(CO)2 and CO disproportionation do not occur, and this evidence is discussed in terms of support effect.

Sign in / Sign up

Export Citation Format

Share Document