Development of an Automated TDR System for Package Failure Analysis

Author(s):  
Christopher C. Basilioa ◽  
Hieu Trong Nguyenb ◽  
Arlene Aguinaldoc ◽  
Jan Paul Arboledac ◽  
Richmond Angd ◽  
...  

Abstract This paper describes the successful effort to develop the Time Domain Reflectometry (TDR) tool by automating the equipment process. The current challenges in the tool usage brought about by miniaturization in the package technology presented itself as an opportunity for the tool improvement. The authors were able to devise an automated TDR system which is ergonomically safe, yielded a significant through put time reduction and provide a consistent and accurate result. This comes at a lower cost in comparison to the current system available in the Virtual Factory (VF).

Author(s):  
Kendall Scott Wills ◽  
Omar Diaz de Leon ◽  
Kartik Ramanujachar ◽  
Charles P. Todd

Abstract In the current generations of devices the die and its package are closely integrated to achieve desired performance and form factor. As a result, localization of continuity failures to either the die or the package is a challenging step in failure analysis of such devices. Time Domain Reflectometry [1] (TDR) is used to localize continuity failures. However the accuracy of measurement with TDR is inadequate for effective localization of the failsite. Additionally, this technique does not provide direct 3-Dimenstional information about the location of the defect. Super-conducting Quantum Interference Device (SQUID) Microscope is useful in localizing shorts in packages [2]. SQUID microscope can localize defects to within 5um in the X and Y directions and 35um in the Z direction. This accuracy is valuable in precise localization of the failsite within the die, package or the interfacial region in flipchip assemblies.


Author(s):  
Bilal Abd-AlRahman ◽  
Corey Lewis ◽  
Todd Simons

Abstract A failure analysis application utilizing scanning acoustic microscopy (SAM) and time domain reflectometry (TDR) for failure analysis has been developed to isolate broken stitch bonds in thin shrink small outline package (TSSOP) devices. Open circuit failures have occurred in this package due to excessive bending of the leads during assembly. The tools and their specific application to this technique as well as the limitations of C-SAM, TDR and radiographic analyses are discussed. By coupling C-SAM and TDR, a failure analyst can confidently determine whether the cause of an open circuit in a TSSOP package is located at the stitch bond. The root cause of the failure was determined to be abnormal mechanical stress placed on the pins during the lead forming operation. While C-SAM and TDR had proven useful in the analysis of TSSOP packages, it can potentially be expanded to other wire-bonded packages.


Author(s):  
Teoh King Long ◽  
Ko Yin Fern

Abstract In time domain reflectometry (TDR), the main emphasis lies on the reflected waveform. Poor probing contact is one of the common problems in getting an accurate waveform. TDR probe normalization is essential before measuring any TDR waveforms. The advantages of normalization include removal of test setup errors in the original test pulse and the establishment of a measurement reference plane. This article presents two case histories. The first case is about a Plastic Ball Grid Array package consisting of 352 solder balls where the open failure mode was encountered at various terminals after reliability assessment. In the second, a three-digit display LED suspected of an electrical short failure was analyzed using TDR as a fault isolation tool. TDR has been successfully used to perform non-destructive fault isolation in assisting the routine failure analysis of open and short failure. It is shown to be accurate and reduces the time needed to identify fault locations.


Irriga ◽  
2018 ◽  
Vol 14 (4) ◽  
pp. 564-577 ◽  
Author(s):  
Leonardo Do Nascimento Lopes ◽  
Elton Martins ◽  
Bruno De Lima Santoro ◽  
Claudinei Fonseca Souza

CARACTERIZAÇÃO DA DISTRIBUIÇÃO DA ÁGUA NO SOLO PARA IRRIGAÇÃO POR GOTEJAMENTO  Leonardo do Nascimento Lopes1; Elton Martins2; Bruno de Lima Santoro2; Claudinei Fonseca Souza31Universidade de Taubaté, Unitau, Taubaté, SP,  [email protected] Engenharia Civil e Ambiental, Universidade de Taubaté, Taubaté, Unitau, SP 3Departamento de Recursos Naturais e Proteção Ambiental, Universidade Federal São Carlos, São Carlos, SP  1 RESUMO O conhecimento da distribuição da água no solo é de grande importância para a agricultura, uma vez que a água é um dos fatores que mais influenciam o rendimento das culturas. Existem muitas técnicas utilizadas para o monitoramento do conteúdo de água do solo, a reflectometria domínio do tempo (TDR) tem sido difundida entre os pesquisadores por apresentar várias vantagens, entre as quais a determinação em tempo real e a possibilidade de leituras automatizadas. O principal objetivo desta pesquisa foi avaliar a distribuição da água no perfil de um Latossolo Vermelho-Amarelo. Sondas de Reflectometria no domínio do Tempo (TDR) foram utilizadas para monitorar a distribuição de água no solo aplicada através de gotejadores de fluxo constante nas taxas de 2, 4 e 8 Lh-1. Considerando os resultados de diferentes perfis, observa-se um maior armazenamento da água próximo do gotejador diminuindo progressivamente para frente de molhamento. Aproximadamente, um terço da água aplicada (33%) foi armazenado na primeira camada (0-0,10 m) para todos os ensaios. Comparando diferentes taxas de aplicação, observa-se maior armazenamento de água para o gotejador de 8L h-1, com 30, 33 e 34% de água aplicada acumulada na primeira camada (0-0.10 m) para gotejadores de 2, 4 e 8L h-1, respectivamente. Os resultados sugerem que, com base no volume e frequência utilizada neste experimento, seria vantajoso aplicar pequenas quantidades de água em intervalos mais frequentes para reduzir perdas por percolação. UNITERMOS: TDR, conteúdo de água, bulbo molhado  LOPES, L. N.; MARTINS, E.; SANTORO, B. L.; SOUZA, C. F.WATER DISTRIBUTION CHARACTERIZATION IN SOIL FOR DRIP IRRIGATION   2 ABSTRACT Knowledge of water distribution in soil is of great importance to agriculture, since water is one of the factors that most influence the yield of crops. There are many techniques used to monitor soil water content. The time domain reflectometry (TDR) has been widespread among researchers because it presents several advantages, among which the determination in real time and possibility of automated readings. The main goal of this research was to evaluatethe water distribution in a profile of Red-Yellow Oxisol. Time domain reflectometry (TDR) probes were used to monitor the water distribution from drippers discharging at constant flow rates of 2, 4 and 8 Lh-1 in soil. Considering results from different profiles, we observed greater water storage near the dripper decreasing gradually towards the wetting front. About one third of the applied water (33%) was stored in the first layer (0-0.10 m) for all experiments. Comparing different dripper flow rates, we observed higher water storage for 8 L h-1, with 30, 33 and 34% of applied water accumulating in the first layer (0-0.10m) for dripper flow rates of 2, 4 and 8 L h-1, respectively. The results suggest that based on the volume and frequency used in this experiment, it would be advantageous to apply small amounts of water at more frequent intervals to reduce deep percolation losses of applied water. KEYWORDS: TDR, water content, wetted soil volume


1982 ◽  
Vol 19 (4) ◽  
pp. 511-517 ◽  
Author(s):  
T. H. W. Baker ◽  
J. L. Davis ◽  
H. N. Hayhoe ◽  
G. C. Topp

The time-domain reflectometry technique was compared with the temperature measurement method for locating the frozen–unfrozen interface in water and sandy soils. This technique depends on the high-frequency (1–1000 MHz) electrical properties of water that change significantly and abruptly between the liquid and solid phases. Parallel wire transmission lines were inserted into the soil to guide electromagnetic pulses produced by a time-domain reflectometer (TDR). The frozen–unfrozen interface produced reflections measured by the TDR which were in turn used to locate the interface as it moved along the transmission line. In the laboratory it was possible to locate the interface using the TDR to within ±0.5 cm and in the field to within ±2.4 cm. These errors were equal to those associated with the temperature measurements. Keywords: soil freezing, temperature measurements, dielectric constant, time-domain reflectometry.


Sign in / Sign up

Export Citation Format

Share Document