Super-Conducting Quantum Interference Device Technique: 3-D Localization of a Short within a Flip Chip Assembly

2001 ◽  
Author(s):  
Kendall Scott Wills ◽  
Omar Diaz de Leon ◽  
Kartik Ramanujachar ◽  
Charles P. Todd
Keyword(s):  
Form Factor ◽  
Failure Analysis ◽  
Time Domain ◽  
Quantum Interference ◽  
Flip Chip ◽  
Time Domain Reflectometry ◽  
Interfacial Region ◽  
Precise Localization ◽  
Super Conducting ◽  
Accuracy Of Measurement

Abstract In the current generations of devices the die and its package are closely integrated to achieve desired performance and form factor. As a result, localization of continuity failures to either the die or the package is a challenging step in failure analysis of such devices. Time Domain Reflectometry [1] (TDR) is used to localize continuity failures. However the accuracy of measurement with TDR is inadequate for effective localization of the failsite. Additionally, this technique does not provide direct 3-Dimenstional information about the location of the defect. Super-conducting Quantum Interference Device (SQUID) Microscope is useful in localizing shorts in packages [2]. SQUID microscope can localize defects to within 5um in the X and Y directions and 35um in the Z direction. This accuracy is valuable in precise localization of the failsite within the die, package or the interfacial region in flipchip assemblies.

Advanced Non-Destructive Fault Isolation Techniques for PCB Substrates Using Magnetic Current Imaging and Terahertz Time Domain Reflectometry

2018 ◽  
Author(s):  
Daechul Choi ◽  
Yoonseong Kim ◽  
Jongyun Kim ◽  
Han Kim
Keyword(s):  
Time Domain ◽  
Quantum Interference ◽  
Flip Chip ◽  
Imaging System ◽  
Time Domain Reflectometry ◽  
Fault Isolation ◽  
Magnetic Current ◽  
Isolation Techniques ◽  
Super Conducting ◽  
Non Destructive

Abstract In this paper, we demonstrate cases for actual short and open failures in FCB (Flip Chip Bonding) substrates by using novel non-destructive techniques, known as SSM (Scanning Super-conducting Quantum Interference Device Microscopy) and Terahertz TDR (Time Domain Reflectometry) which is able to pinpoint failure locations. In addition, the defect location and accuracy is verified by a NIR (Near Infra-red) imaging system which is also one of the commonly used non-destructive failure analysis tools, and good agreement was made.

Time Domain Reflectometry as a Device Packaging Level Failure Analysis and Failure Localization Tool

2000 ◽  
Author(s):  
Damion T. Searls ◽  
Anura Don ◽  
Emilie Dy ◽  
Deepak Goyal
Keyword(s):  
Failure Analysis ◽  
Time Domain ◽  
Flip Chip ◽  
Low Voltage ◽  
Time Domain Reflectometry ◽  
Stress Tests ◽  
X Ray ◽  
Customer Returns ◽  
Failure Location ◽  
Electrical Connectivity

Abstract Detecting failure in electrical connectivity at the component packaging level is a major expenditure of the industry’s failure analysis (FA) resources. These package failures can result from material/manufacturing excursions, stress tests, and/or customer returns. However, many of the methods employed currently (such as X-ray or crosssectioning) can fall short in terms of throughput time, or success rate. Moreover, many FA techniques can be destructive and therefore leave the sample useless for subsequent tests. On the other hand, time domain reflectometry (TDR) can be used as a component packaging level FA tool which meets the needs of quickly, precisely, and non-destructively locating electrical connectivity problems in signal traces. Once the failure location has been pin pointed, other FA methods (X-ray, cross-section, etc.) can be used more easily to determine why the failure occurred. Since TDR testing involves no physical preparation, the sample will be completely intact for subsequent tests. TDR uses a low voltage, low current, and very short rise time voltage pulse to determine the impedance of a signal trace as a function of time. With a waveform of trace impedance versus time, not only can the presence of a failure be detected, but the distance along the trace to the anomaly can also be quickly determined. This paper presents TDR as a useful tool for package level failure analysis labs. The paper proposes one set of solutions for enabling effective TDR analysis (e.g., TDR test fixturing), and discusses some TDR methodologies for detecting and locating anomalies. The methodologies will be illustrated using three example cases that reflect some commonly used packaging technologies: Flip-Chip Organic Land Grid Array (FC-OLGA), Flip-Chip Pin Grid Array (FC-PGA), and Plastic Land Grid Array (PLGA).

Failure Analysis of Broken Stitch Bonds in TSSOP Packages Using Scanning Acoustic Microscopy (SAM) and Time Domain Reflectometry (TDR)

2004 ◽  
Author(s):  
Bilal Abd-AlRahman ◽  
Corey Lewis ◽  
Todd Simons
Keyword(s):  
Failure Analysis ◽  
Mechanical Stress ◽  
Time Domain ◽  
Open Circuit ◽  
Time Domain Reflectometry ◽  
Acoustic Microscopy ◽  
Scanning Acoustic Microscopy ◽  
Root Cause ◽  
Analysis Application

Abstract A failure analysis application utilizing scanning acoustic microscopy (SAM) and time domain reflectometry (TDR) for failure analysis has been developed to isolate broken stitch bonds in thin shrink small outline package (TSSOP) devices. Open circuit failures have occurred in this package due to excessive bending of the leads during assembly. The tools and their specific application to this technique as well as the limitations of C-SAM, TDR and radiographic analyses are discussed. By coupling C-SAM and TDR, a failure analyst can confidently determine whether the cause of an open circuit in a TSSOP package is located at the stitch bond. The root cause of the failure was determined to be abnormal mechanical stress placed on the pins during the lead forming operation. While C-SAM and TDR had proven useful in the analysis of TSSOP packages, it can potentially be expanded to other wire-bonded packages.

Time Domain Reflectometry Technique for Failure Analysis

2004 ◽  
Author(s):  
Teoh King Long ◽  
Ko Yin Fern
Keyword(s):  
Failure Analysis ◽  
Time Domain ◽  
Time Domain Reflectometry ◽  
Fault Isolation ◽  
Reference Plane ◽  
First Case ◽  
Main Emphasis ◽  
Plastic Ball ◽  
Solder Balls ◽  
Non Destructive

Abstract In time domain reflectometry (TDR), the main emphasis lies on the reflected waveform. Poor probing contact is one of the common problems in getting an accurate waveform. TDR probe normalization is essential before measuring any TDR waveforms. The advantages of normalization include removal of test setup errors in the original test pulse and the establishment of a measurement reference plane. This article presents two case histories. The first case is about a Plastic Ball Grid Array package consisting of 352 solder balls where the open failure mode was encountered at various terminals after reliability assessment. In the second, a three-digit display LED suspected of an electrical short failure was analyzed using TDR as a fault isolation tool. TDR has been successfully used to perform non-destructive fault isolation in assisting the routine failure analysis of open and short failure. It is shown to be accurate and reduces the time needed to identify fault locations.

Advanced Fault Isolation Technique Using Electro-Optical Terahertz Pulse Reflectometry (EOTPR) for 2D and 2.5D Flip-Chip Package

2012 ◽  
Author(s):  
Lihong Cao ◽  
Manasa Venkata ◽  
Meng Yeow Tay ◽  
Wen Qiu ◽  
J. Alton ◽  
...  
Keyword(s):  
Time Domain ◽  
Flip Chip ◽  
Time Domain Reflectometry ◽  
Fault Isolation ◽  
Experimental Results ◽  
Terahertz Pulse ◽  
Isolation And Identification ◽  
Isolation Technique ◽  
Non Destructive

Abstract Electro-optical terahertz pulse reflectometry (EOTPR) was introduced last year to isolate faults in advanced IC packages. The EOTPR system provides 10μm accuracy that can be used to non-destructively localize a package-level failure. In this paper, an EOTPR system is used for non-destructive fault isolation and identification for both 2D and 2.5D with TSV structure of flip-chip packages. The experimental results demonstrate higher accuracy of the EOTPR system in determining the distance to defect compared to the traditional time-domain reflectometry (TDR) systems.

Non-Destructive Open Fault Isolation in Flip-Chip Devices with Space-Domain Reflectometry

2013 ◽  
Author(s):  
W. Qiu ◽  
M.S. Wei ◽  
J. Gaudestad ◽  
V.V. Talanov
Keyword(s):  
Quantum Interference ◽  
Flip Chip ◽  
Time Domain Reflectometry ◽  
Fault Isolation ◽  
Superconducting Quantum Interference Device ◽  
Isolation Method ◽  
Space Domain ◽  
Open Faults ◽  
Scanning Squid ◽  
Non Destructive

Abstract Space-domain reflectometry (SDR) utilizing scanning superconducting quantum interference device (SQUID) microscopy is a newly developed non-destructive failure analysis (FA) technique for open fault isolation. Unlike the conventional open fault isolation method, time-domain reflectometry (TDR), scanning SQUID SDR provides a truly two-dimensional physical image of device under test with spatial resolution down to 30 μm [1]. In this paper, the SQUID SDR technique is used to isolate dead open faults in flip-chip devices. The experimental results demonstrate the capability of SDR in open fault detection

Localization of Dead Open in a Solder Bump by Space Domain Reflectometry

2012 ◽  
Author(s):  
David P. Vallett ◽  
Daniel A. Bader ◽  
Vladimir V. Talanov ◽  
Jan Gaudestad ◽  
Nicolas Gagliolo ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Failure Analysis ◽  
Quantum Interference ◽  
Flip Chip ◽  
Solder Bump ◽  
Frequency Range ◽  
Superconducting Quantum Interference Device ◽  
Space Domain ◽  
Non Destructive ◽  
The Magnetic Field

Abstract Space Domain Reflectometry (SDR) is a newly developed non-destructive failure analysis (FA) technique for localizing open defects in both packages and dies through mapping in space domain the magnetic field produced by a radio frequency (RF) current induced in the sample, herein the name Space Domain Reflectometry. The technique employs a scanning superconducting quantum interference device (SQUID) RF microscope operating over a frequency range from 60 to 200 MHz. In this paper we demonstrate that SDR is capable of locating defective micro bumps in a flip-chip device.

Sign in / Sign up

Export Citation Format

Share Document