Powder Impact Temperature Influence on Metallurgical Bonding—An Investigation for Soft Particle Deposition on Hard Substrate

2021 ◽  
Author(s):  
A. Nastic ◽  
B. Jodoin ◽  
D. Poirier ◽  
J.-G. Legoux
Keyword(s):  
Particle Size ◽  
Particle Deposition ◽  
Deposition Efficiency ◽  
Impact Behavior ◽  
Particle Impact ◽  
Soft Particle ◽  
Metallurgical Bonding ◽  
Computational Fluid Dynamics Cfd ◽  
Spray Field

Abstract Segregating the convoluted effects of particle size; impact temperature and velocity on deposition behavior and adhesion is of utmost interest to the cold spray field. The current study aims to associate the particle impact behavior and adhesion to its in-flight characteristics by studying and decoupling the influence of particle size; temperature and velocity for single particle impacts and full coatings. Experimental results reveal that in-situ peening processes contribute to the adhesion at low impact temperature while η (V.VC) controls the adhesion/cohesion at increased particle impact temperatures. The benefits of both bonding mechanisms are discussed in terms of measured adhesion/cohesion; bend-to-break fracture surfaces; pseudoplasticity; deposition efficiency and critical velocity. Computational fluid dynamics (CFD) results provide individual particle trajectory; size; temperature and velocity; of successfully deposited particles; which have led to the observed signs of metallurgical bonding.

Comparison of Micro- and Nano-Size Particle Transport and Depositions in 90 Degree Bend Microchannel

2009 ◽  
Author(s):  
Kai Zhang ◽  
Jianzhong Lin ◽  
Mingzhou Yu
Keyword(s):  
Particle Size ◽  
Electric Field ◽  
Finite Volume Method ◽  
Finite Volume ◽  
Particle Deposition ◽  
Particle Diameter ◽  
Deposition Efficiency ◽  
Size Particle ◽  
Volume Method ◽  
Nano Size

The flow and electric field are simulated numerically with finite volume method first, then large number of nanoparticles and microparticles are injected into the microchannel separately, and these particles are traced with the Lagrangian method. It has been found that particle deposition efficiency in the bend usually decreases first then increases with particle size increasing, and there usually exists a minimum value and it corresponds to the particle diameter of about 3μm, which means that kind of particle can transport longer distance. The electric field doesn’t affect that specified value. This conclusion is helpful to the optimization of the design of microchips.

Novel Formulation Development and Evaluation of Nanoparticles Based in Situ Gelling System for The Ophthalmic Delivery of Ciprofloxacin Hydrochloride

2015 ◽  
Vol 5 (4) ◽  
Author(s):  
Kranti Singh ◽  
Surajpal Verma ◽  
Shyam Prasad ◽  
Indu Bala
Keyword(s):  
Particle Size ◽  
Zeta Potential ◽  
Drug Loading ◽  
In Vitro Release ◽  
Formulation Development ◽  
Ciprofloxacin Hydrochloride ◽  
Potential Value ◽  
The Mean ◽  
In Situ Gelling

Ciprofloxacin hydrochloride loaded Eudragit RS100 nanoparticles were prepared by using w/o/w emulsification (multiple emulsification) solvent evaporation followed by drying of nanoparticles at 50°C. The nanoparticles were further incorporated into the pH-triggered in situ gel forming system which was prepared using Carbopol 940 in combination with HPMC as viscosifying agent. The developed nanoparticles was evaluated for particle size, zeta potential value and loading efficiency; nanoparticle incorporated in situ gelling system was evaluated for pH, clarity, gelling strength, rheological studies, in-vitro release studies and ex-vivo precorneal permeation studies. The nanopaticle showed the mean particle size varying between 263.5nm - 325.9 nm with the mean zeta potential value of -5.91 mV to -8.13 mV and drug loading capacity varied individually between 72.50% to 98.70% w/w. The formulation was clear with no suspended particles, showed good gelling properties. The gelling was quick and remained for longer time period. The developed formulation was therapeutically efficacious, stable and non-irritant. It provided the sustained release of drug over a period of 8-10 hours.

scholarly journals A Numerical Study of the Effect of Particle Size on Particle Deposition on Turbine Vanes and Blades

2021 ◽  
Vol 13 (5) ◽  
pp. 168781402110178
Author(s):  
Zhengang Liu ◽  
Weinan Diao ◽  
Zhenxia Liu ◽  
Fei Zhang
Keyword(s):  
Particle Size ◽  
Particle Deposition ◽  
Numerical Study ◽  
Stokes Number ◽  
Capture Efficiency ◽  
Particle Capture ◽  
Factors Affecting ◽  
Pressure Surface ◽  
Deposition Area ◽  
Turbine Vanes

Particle deposition could decrease the aerodynamic performance and cooling efficiency of turbine vanes and blades. The particle motion in the flow and its temperature are two important factors affecting its deposition. The size of the particle influences both its motion and temperature. In this study, the motion of particles with the sizes from 1 to 20 μm in the first stage of a turbine are firstly numerically simulated with the steady method, then the particle deposition on the vanes and blades are numerically simulated with the unsteady method based on the critical viscosity model. It is discovered that the particle deposition on vanes mainly formed near the leading and trailing edge on the pressure surface, and the deposition area expands slowly to the whole pressure surface with the particle size increasing. For the particle deposition on blades, the deposition area moves from the entire pressure surface toward the tip with the particle size increasing due to the effect of rotation. For vanes, the particle capture efficiency increases with the particle size increasing since Stokes number and temperature of the particle both increase with its size. For blades, the particle capture efficiency increases firstly and then decreases with the particle size increasing.

scholarly journals Experimental and CFD Simulations of the Aerosol Flow in the Air Ventilating the Underground Excavation in Terms of SARS-CoV-2 Transmission

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4743
Author(s):  
Tomasz Janoszek ◽  
Zbigniew Lubosik ◽  
Lucjan Świerczek ◽  
Andrzej Walentek ◽  
Jerzy Jaroszewicz
Keyword(s):  
Numerical Calculations ◽  
Mining Institute ◽  
Ventilation Network ◽  
Underground Excavation ◽  
In Situ Tests ◽  
Ansys Fluent ◽  
Aerosol Emission ◽  
Ansys Cfx ◽  
Computational Fluid Dynamics Cfd

The paper presents the results of experimental and model tests of transport of dispersed fluid droplets forming a cloud of aerosol in a stream of air ventilating a selected section of the underground excavation. The excavation selected for testing is part of the ventilation network of the Experimental Mine Barbara of the Central Mining Institute. For given environmental conditions, such as temperature, pressure, relative humidity, and velocity of air, the distribution of aerosol droplet changes in the mixture of air and water vapor along the excavation at a distance was measured at 10 m, 25 m, and 50 m from the source of its emission. The source of aerosol emission in the excavation space was a water nozzle that was located 25 m from the inlet (inlet) of the excavation. The obtained results of in situ tests were related to the results of numerical calculations using computational fluid dynamics (CFD). Numerical calculations were performed using Ansys-Fluent and Ansys-CFX software. The dimensions and geometry of the excavation under investigation are presented. The authors describe the adopted assumptions and conditions for the numerical model and discuss the results of the numerical solution.

Effect of particle size on in-situ desulfurization for oxy-fuel CFBC

Fuel ◽  
2021 ◽  
Vol 291 ◽  
pp. 120270
Author(s):  
Seo Yeong Kang ◽  
Su Been Seo ◽  
Eun Sol Go ◽  
Hyung Woo Kim ◽  
Sang In Keel ◽  
...  
Keyword(s):  
Particle Size ◽  
Effect Of Particle Size

scholarly journals Effects of processing, moisture, and storage length on the fermentation profile, particle size, and ruminal disappearance of reconstituted corn grain

2020 ◽  
Vol 98 (11) ◽  
Author(s):  
Ana L M Gomes ◽  
Antonio V I Bueno ◽  
Fernando A Jacovaci ◽  
Guilherme Donadel ◽  
Luiz F Ferraretto ◽  
...  
Keyword(s):  
Particle Size ◽  
Lactic Acid ◽  
Butyric Acid ◽  
Hammer Mill ◽  
Moisture Concentration ◽  
Fermentation Profile ◽  
And Storage ◽  
Ground Corn ◽  
Corn Grain

Abstract Our objective was to examine the effects of processing, moisture, and anaerobic storage length of reconstituted corn grain (RCG) on the fermentation profile, geometric mean particle size (GMPS), and ruminal dry matter disappearance (DMD). Dry corn kernels were ground (hammer mill, 5-mm screen) or rolled, then rehydrated to 30%, 35%, or 40% moisture, and stored for 0, 14, 30, 60, 90, 120, or 180 d in laboratory silos. Rolled corn had an increased GMPS compared with ground corn (2.24 and 1.13 mm, respectively, at ensiling). However, there was a trend for an interaction between processing and moisture concentration to affect particle size, with GMPS increasing with increased moisture concentration, especially in ground corn. Longer storage periods also slightly increased GMPS. Processing, moisture, and storage length interacted to affect the fermentation pattern (two- or three-way interactions). Overall, pH decreased, whereas lactic acid, acetic acid, ethanol, and NH3-N increased with storage length. RCG with 30% moisture had less lactic acid than corn with 35% and 40% moisture, indicating that fermentation might have been curtailed and also due to the clostridial fermentation that converts lactic acid to butyric acid. Ensiling reconstituted ground corn with 30% of moisture led to greater concentrations of ethanol and butyric acid, resulting in greater DM loss than grain rehydrated to 35% or 40% of moisture. Ammonia-N and in situ ruminal DMD were highest for reconstituted ground corn with 35% or 40% of moisture, mainly after 60 d of storage. Therefore, longer storage periods and greater moisture contents did not offset the negative effect of greater particle size on the in situ ruminal DMD of rolled RCG. Nonetheless, RCG should be ensiled with more than 30% moisture and stored for at least 2 mo to improve the ruminal DMD and reduce the formation of ethanol and butyric acid.

scholarly journals Population Balance Application in TiO2 Particle Deagglomeration Process Modeling

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3523
Author(s):  
Radosław Krzosa ◽  
Łukasz Makowski ◽  
Wojciech Orciuch ◽  
Radosław Adamek
Keyword(s):  
Particle Size ◽  
Titanium Dioxide ◽  
Mechanistic Model ◽  
Population Balance ◽  
Tio2 Particle ◽  
Application Process ◽  
Titanium Dioxide Powder ◽  
Dioxide Powder ◽  
Computational Fluid Dynamics Cfd ◽  
Hydrodynamic Stresses

The deagglomeration of titanium-dioxide powder in water suspension performed in a stirring tank was investigated. Owing to the widespread applications of the deagglomeration process and titanium dioxide powder, new, more efficient devices and methods of predicting the process result are highly needed. A brief literature review of the application process, the device used, and process mechanism is presented herein. In the experiments, deagglomeration of the titanium dioxide suspension was performed. The change in particle size distribution in time was investigated for different impeller geometries and rotational speeds. The modification of impeller geometry allowed the improvement of the process of solid particle breakage. In the modelling part, numerical simulations of the chosen impeller geometries were performed using computational-fluid-dynamics (CFD) methods whereby the flow field, hydrodynamic stresses, and other useful parameters were calculated. Finally, based on the simulation results, the population-balance with a mechanistic model of suspension flow was developed. Model predictions of the change in particle size showed good agreement with the experimental data. Using the presented method in the process design allowed the prediction of the product size and the comparison of the efficiency of different impeller geometries.

scholarly journals In Situ Synthesis of Core-Shell-Structured SiCp Reinforcements in Aluminium Matrix Composites by Powder Metallurgy

Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1201
Author(s):  
Xinghua Ji ◽  
Cheng Zhang ◽  
Shufeng Li
Keyword(s):  
Particle Size ◽  
Powder Metallurgy ◽  
Shell Structure ◽  
Ex Situ ◽  
Aluminium Matrix ◽  
Core Shell ◽  
Matrix Composites ◽  
Aluminium Matrix Composites ◽  
Core Shell Structure

SiCp reinforced aluminium matrix composites (AMCs), which are widely used in the aerospace, automotive, and electronic packaging fields along with others, are usually prepared by ex situ techniques. However, interfacial contamination and poor wettability of the ex situ techniques make further improvement in their comprehensive performance difficult. In this paper, SiCp reinforced AMCs with theoretical volume fractions of 15, 20, and 30% are prepared by powder metallurgy and in situ reaction via an Al-Si-C system. Moreover, a combined method of external addition and an in situ method is used to investigate the synergistic effect of ex situ and in situ SiCp on AMCs. SiC particles can be formed by an indirect reaction: 4Al + 3C → Al4C3 and Al4C3 + 3Si → 3SiC + 4Al. This reaction is mainly through the diffusion of Si, in which Si diffuses around Al4C3 and then reacts with Al4C3 to form SiCp. The in situ SiC particles have a smooth boundary, and the particle size is approximately 1–3 μm. A core-shell structure having good bonding with an aluminium matrix was generated, which consists of an ex situ SiC core and an in situ SiC shell with a thickness of 1–5 μm. The yield strength and ultimate tensile strength of in situ SiCp reinforced AMCs can be significantly increased with a constant ductility by adding 5% ex situ SiCp for Al-28Si-7C. The graphite particle size has a significant effect on the properties of the alloy. A criterion to determine whether Al4C3 is a complete reaction is achieved, and the forming mechanism of the core-shell structure is analysed.

scholarly journals Numerical Simulation of the Aerosol Particle Motion in Granular Filters with Solid and Porous Granules

Processes ◽  
2021 ◽  
Vol 9 (2) ◽  
pp. 268
Author(s):  
Olga V. Soloveva ◽  
Sergei A. Solovev ◽  
Ruzil R. Yafizov
Keyword(s):  
Numerical Simulation ◽  
Aerosol Particle ◽  
Particle Deposition ◽  
Particle Diameter ◽  
Deposition Efficiency ◽  
Hydrodynamic Resistance ◽  
Hydrodynamic Properties ◽  
Granular Filters ◽  
Limiting Value ◽  
Good Agreement

In this work, a study was carried out to compare the filtering and hydrodynamic properties of granular filters with solid spherical granules and spherical granules with modifications in the form of micropores. We used the discrete element method (DEM) to construct the geometry of the filters. Models of granular filters with spherical granules with diameters of 3, 4, and 5 mm, and with porosity values of 0.439, 0.466, and 0.477, respectively, were created. The results of the numerical simulation are in good agreement with the experimental data of other authors. We created models of granular filters containing micropores with different porosity values (0.158–0.366) in order to study the micropores’ effect on the aerosol motion. The study showed that micropores contribute to a decrease in hydrodynamic resistance and an increase in particle deposition efficiency. There is also a maximum limiting value of the granule microporosity for a given aerosol particle diameter when a further increase in microporosity leads to a decrease in the deposition efficiency.

Sign in / Sign up

Export Citation Format

Share Document