scholarly journals Study of the thermal treatment modes influence on the forming of microstructure and specified complex of mechanical properties of high-strength sheet product with guaranteed level of hardness (400–450 HB) of low-alloyed steel

2019 ◽  
Vol 75 (4) ◽  
pp. 480-487
Author(s):  
M. Yu. Matrosov ◽  
P. G. Martynov ◽  
A. V. Mitrofanov ◽  
K. Yu. Barabash ◽  
T. V. Goroshko ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fine Structure ◽  
Thermal Treatment ◽  
Hot Rolling ◽  
High Strength ◽  
Controlled Rolling ◽  
Alloyed Steel ◽  
Accelerated Cooling ◽  
Cold Forming ◽  
Low Alloyed Steel

High-strength sheet product of low-alloyed steel, used at manufacturing of heavy-loaded structures, must have, apart from wear resistance, high toughness, good weldability, ability to hot and cold forming, machinability and low cost. Combination of these properties based on forming fine grain austenite structure before the martensitic transformation at definite its thermal treatment modes. Results of study of microstructure, fine structure and mechanical properties of high-strength boron-containing low-alloyed steel after different technological methods of the rolled product manufacturing presented: high-temperature hot rolling and twostages controlled rolling with accelerated cooling followed by thermal treatment – quenching with tempering. Variants of optimal modes of thermal treatment determined, providing combination of high level of impact toughness under negative temperatures, hardness and strength properties of sheet product. The two considered in the article technological variants, comprising treatment of low-alloyed steel with boron (hot rolling and two-stages controlled rolling with accelerated cooling) followed by thermal treatment results in forming fine structure of tempered martensite, which provides high mechanical properties, meeting the made requirements. Depending on the heating temperature before quenching in the range 770–950 °С, the morphology of the actual steel grain is changing from elongated to equiaxed, which is connected with the metal recrystallization process during heating after plastic deformation. The study results obtained allow to optimize the thermal treatment processes of sheet product of low-alloyed boron containing steel for particular conditions of application.

Process, Microstructure and Mechanical Properties of X90 Pipeline Steel

2016 ◽  
Vol 850 ◽  
pp. 894-898
Author(s):  
Bin Guo ◽  
Jin Qiao Xu ◽  
Lei Cui ◽  
Qing Feng Wang
Keyword(s):  
Mechanical Properties ◽  
Manufacturing Process ◽  
Pipeline Steel ◽  
Structural Characteristics ◽  
High Strength ◽  
Controlled Rolling ◽  
Accelerated Cooling ◽  
Iron And Steel ◽  
Technical Requirements ◽  
China National Petroleum Corporation

This paper provided a detailed description of X90 pipeline steel developed in Wuhan Iron and Steel Corporation (WISCO), including its metallurgical design, manufacturing process, structural characteristics and mechanical properties. Some key issues such as the cooling rate and rolling parameters were addressed for the development of X90 pipeline steel. The experimental results showed that the manufacturing process of controlled rolling (for austenite refining) + relaxation (for ferrite phase transformation) +ultrafast accelerated cooling could guarantee very fine microstructure and excellent mechanical properties. The X90 pipeline steel developed in WISCO has a good match of high strength and excellent toughness. Mechanical properties of X90 coils, plates and corresponding SSAW and LSAW pipes comprehensively meet the technical requirements of China National Petroleum Corporation (CNPC).

Recent Development in High Strength Linepipe for Sour Environment

2003 ◽  
Author(s):  
Nobuyuki Ishikawa ◽  
Toyohisa Shinmiya ◽  
Shigeru Endo ◽  
Tsunemi Wada ◽  
Joe Kondo
Keyword(s):  
Mechanical Properties ◽  
High Strength ◽  
Controlled Rolling ◽  
Accelerated Cooling ◽  
Optimum Conditions ◽  
Microstructural Characteristics ◽  
Design Concepts ◽  
Bainitic Microstructure ◽  
Linepipe Steels ◽  
Sour Gas

This paper firstly summarizes the design concepts for controlling crack resistant property and mechanical properties of high strength linepipe steels for sour gas service. Optimum conditions of controlled rolling and accelerated cooling that balances crack resistant property and toughness were investigated. It was demonstrated that higher cooling rate in accelerated cooling process brings tremendous advantages for balancing toughness and strength by fine bainitic microstructure even for heavy wall thick pipes. Production results of high strength sour resistant linepipes were introduced. In order to increase strength grade of sour linepipes, further investigation was made using the steels with different microstructures. It was found that precipitation hardened ferrite-bainite steels have extremely high resistance against HIC even for Grade X80. Mechanical properties and microstructural characteristics of this newly developed steel were introduced in this paper.

scholarly journals Features of the ferrite-bainite structure low-alloy low-carbon steel after heat hardening and subsequent tempering

2021 ◽  
pp. 33-47
Author(s):  
L.M. Deineko ◽  
A.Yu. Borysenko ◽  
A.О. Taranenko ◽  
T.O. Zaitseva ◽  
N.S. Romanova
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Controlled Rolling ◽  
Alloyed Steel ◽  
Low Alloy Steels ◽  
Low Carbon ◽  
Finished Steel ◽  
Bainite Structure ◽  
Bainitic Structure ◽  
Low Alloyed Steel

Problem statement. In recent decades, there has been a tendency to increase the mechanical properties of low-carbon, low-alloyed steel plate iron by using controlled rolling or hardening heat treatment of finished steel parts. At the same time, for welded parts, the most suitable is a metal having a ferrite-bainite (or bainite) structure. The work investigated the features of the ferrite-bainite structure of low-carbon and low-alloyed steel 15ХСНД for the production of connecting pipeline parts. Purpose of the article. To establish the laws of formation of a ferritic-bainitic structure in low-carbon low-alloy steels depending on the parameters of heat treatment. Determine the effect of heat treatment parameters on the properties of the connecting parts of pipelines made of these steels. Conclusion. The regularities of the influence of heat treatment parameters on the structure, mechanical properties and topography of fractures of impact samples of 15ХСНД steel with a ferrite-bainitic structure are established. Keywords: stamped-welded connecting parts of man pipelines; heat treatment; microstructure; bainite;mechanical properties; fractography

Effect of Quenching and Partitioning Processing on Microstructure and Mechanical Properties of a Low Alloyed Steel

2018 ◽  
Vol 941 ◽  
pp. 52-57
Author(s):  
Bernd Pfleger ◽  
Marina Gruber ◽  
Gerald Ressel ◽  
Peter Gruber ◽  
Matthew Galler ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Strength ◽  
Phase Evolution ◽  
Tensile Tests ◽  
Austenite Phase ◽  
Phase Fraction ◽  
Quenching Temperature ◽  
Quenching And Partitioning ◽  
Low Alloyed Steel ◽  
A Minor

The concept of quenching and partitioning (Q&P) is a tool to generate steels with high strength and high ductility resulting from a relatively high amount of martensite and austenite. As the parameters of the Q&P treatment influence the strength and ductility properties, the goal of this work was to analyze the effects of varying quenching and partitioning temperatures on the phase evolution, on the retained austenite phase fraction and on the mechanical properties. The phase evolution during heat treatment was analyzed by dilatometer and the microstructure after processing was characterized by light microscopy in combination with color etching according to Klemm. The austenite phase fraction and its carbon content were determined by X-Ray diffraction and the mechanical properties were evaluated by tensile tests. It is shown that the quenching temperature has a minor impact on the phase fraction of austenite as well as its stabilization by carbon and thus, also the mechanical properties. Furthermore, austenite transformation during the partitioning treatment is illustrated.

Sign in / Sign up

Export Citation Format

Share Document