Effect of Quenching and Partitioning Processing on Microstructure and Mechanical Properties of a Low Alloyed Steel

2018 ◽  
Vol 941 ◽  
pp. 52-57
Author(s):  
Bernd Pfleger ◽  
Marina Gruber ◽  
Gerald Ressel ◽  
Peter Gruber ◽  
Matthew Galler ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Strength ◽  
Phase Evolution ◽  
Tensile Tests ◽  
Austenite Phase ◽  
Phase Fraction ◽  
Quenching Temperature ◽  
Quenching And Partitioning ◽  
Low Alloyed Steel ◽  
A Minor

The concept of quenching and partitioning (Q&P) is a tool to generate steels with high strength and high ductility resulting from a relatively high amount of martensite and austenite. As the parameters of the Q&P treatment influence the strength and ductility properties, the goal of this work was to analyze the effects of varying quenching and partitioning temperatures on the phase evolution, on the retained austenite phase fraction and on the mechanical properties. The phase evolution during heat treatment was analyzed by dilatometer and the microstructure after processing was characterized by light microscopy in combination with color etching according to Klemm. The austenite phase fraction and its carbon content were determined by X-Ray diffraction and the mechanical properties were evaluated by tensile tests. It is shown that the quenching temperature has a minor impact on the phase fraction of austenite as well as its stabilization by carbon and thus, also the mechanical properties. Furthermore, austenite transformation during the partitioning treatment is illustrated.

scholarly journals Microstructure Analysis and Mechanical Properties of Low Alloy High Strength Quenched and Partitioned Steel

2016 ◽  
Vol 258 ◽  
pp. 574-578 ◽  
Author(s):  
Farnoosh Forouzan ◽  
Suresh Gunasekaran ◽  
Ali Hedayati ◽  
Esa Vuorinen ◽  
Frank Mücklich
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Lath Martensite ◽  
High Strength ◽  
Microstructure Analysis ◽  
Quenching Temperature ◽  
Precipitate Formation ◽  
Quenching And Partitioning ◽  
Fine Grained ◽  
Impact Tests

Gleeble study of the quenching and partitioning (Q&P) process has been performed on Domex 960 steel (Fe, 0.08 %C, 1.79 %Mn, 0.23 %Si, 0.184 %Ti, and 0.038 %Al). The effect of different Q&P conditions on microstructure and mechanical properties were investigated. The aim of the process is to produce a fine grained microstructure for better ductility and controlled amounts of different micro-constituents to increase the strength and toughness simultaneously. Three different quenching temperatures, three partitioning temperatures and three partitioning times have been selected to process the 27 specimens by Gleeble® 1500. The specimens were characterized by means of OM, SEM, XRD, hardness and impact tests. It was found that, fine lath martensite with retained austenite is achievable without high amount of Si or Al in the composition although lack of these elements may cause the formation of carbides and decrease the available amount of carbon for partitioning into the austenite. The hardness increases as the quenching temperature is decreased, however, at highest partitioning temperature (640◦C) the hardness increases sharply due to extensive precipitate formation.

scholarly journals Heat Treatment Design for a QP Steel: Effect of Partitioning Temperature

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1136
Author(s):  
Marcel Carpio ◽  
Jessica Calvo ◽  
Omar García ◽  
Juan Pablo Pedraza ◽  
José María Cabrera
Keyword(s):  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Tensile Tests ◽  
Quenching Temperature ◽  
Advanced High Strength Steels ◽  
New Family ◽  
Automotive Parts ◽  
Fresh Martensite ◽  
Industry Needs

Designing a new family of advanced high-strength steels (AHSSs) to develop automotive parts that cover early industry needs is the aim of many investigations. One of the candidates in the 3rd family of AHSS are the quenching and partitioning (QP) steels. These steels display an excellent relationship between strength and formability, making them able to fulfill the requirements of safety, while reducing automobile weight to enhance the performance during service. The main attribute of QP steels is the TRIP effect that retained austenite possesses, which allows a significant energy absorption during deformation. The present study is focused on evaluating some process parameters, especially the partitioning temperature, in the microstructures and mechanical properties attained during a QP process. An experimental steel (0.2C-3.5Mn-1.5Si (wt%)) was selected and heated according to the theoretical optimum quenching temperature. For this purpose, heat treatments in a quenching dilatometry and further microstructural and mechanical characterization were carried out by SEM, XRD, EBSD, and hardness and tensile tests, respectively. The samples showed a significant increment in the retained austenite at an increasing partitioning temperature, but with strong penalization on the final ductility due to the large amount of fresh martensite obtained as well.

Investigations on the Mechanical Properties and Formability of Friction Stir Welded Tailored Blanks

2007 ◽  
Vol 344 ◽  
pp. 143-150 ◽  
Author(s):  
Gianluca Buffa ◽  
Livan Fratini ◽  
Marion Merklein ◽  
Detlev Staud
Keyword(s):  
Mechanical Properties ◽  
Stress Condition ◽  
Research Effort ◽  
High Strength Steels ◽  
High Strength ◽  
Tensile Tests ◽  
Friction Stir ◽  
Tailored Blanks ◽  
Sheet Stamping ◽  
Wide Range

Tight competition characterizing automotive industries in the last decades has determined a strong research effort aimed to improve utilized processes and materials in sheet stamping. As far as the latter are regarded light weight alloys, high strength steels and tailored blanks have been increasingly utilized with the aim to reduce parts weight and fuel consumptions. In the paper the mechanical properties and formability of tailored welded blanks made of a precipitation hardenable aluminum alloy but with different sheet thicknesses, have been investigated: both laser welding and friction stir welding have been developed to obtain the tailored blanks. For both welding operations a wide range of the thickness ratios has been considered. The formability of the obtained blanks has been characterized through tensile tests and cup deep drawing tests, in order to show the formability in dependency of the stress condition; what is more mechanical and metallurgical investigations have been made on the welded joints.

scholarly journals Experimental Investigation into Corrosion Effect on Mechanical Properties of High Strength Steel Bars under Dynamic Loadings

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Hui Chen ◽  
Jinjin Zhang ◽  
Jin Yang ◽  
Feilong Ye
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Dynamic Loading ◽  
High Strength Steel ◽  
High Strength ◽  
Tensile Tests ◽  
Reinforcing Steel ◽  
Test Results ◽  
Cross Sectional ◽  
Steel Bars

The tensile behaviors of corroded steel bars are important in the capacity evaluation of corroded reinforced concrete structures. The present paper studies the mechanical behavior of the corroded high strength reinforcing steel bars under static and dynamic loading. High strength reinforcing steel bars were corroded by using accelerated corrosion methods and the tensile tests were carried out under different strain rates. The results showed that the mechanical properties of corroded high strength steel bars were strain rate dependent, and the strain rate effect decreased with the increase of corrosion degree. The decreased nominal yield and ultimate strengths were mainly caused by the reduction of cross-sectional areas, and the decreased ultimate deformation and the shortened yield plateau resulted from the intensified stress concentration at the nonuniform reduction. Based on the test results, reduction factors were proposed to relate the tensile behaviors with the corrosion degree and strain rate for corroded bars. A modified Johnson-Cook strength model of corroded high strength steel bars under dynamic loading was proposed by taking into account the influence of corrosion degree. Comparison between the model and test results showed that proposed model properly describes the dynamic response of the corroded high strength rebars.

scholarly journals Changing in Fatigue Life of 300 M Bainitic Steel After Laser Carburizing and Plasma Nitriding

2018 ◽  
Vol 165 ◽  
pp. 21002 ◽  
Author(s):  
Antonio J. Abdalla ◽  
Douglas Santos ◽  
Getúlio Vasconcelos ◽  
Vladimir H. Baggio-Scheid ◽  
Deivid F. Silva
Keyword(s):  
Mechanical Properties ◽  
Fatigue Life ◽  
Plasma Nitriding ◽  
Fatigue Behavior ◽  
High Strength ◽  
Tensile Tests ◽  
Steel Sample ◽  
Fatigue Tests ◽  
300M Steel ◽  
Structural Applications

In this work 300M steel samples is used. This high-strength steel is used in aeronautic and aerospace industry and other structural applications. Initially the 300 M steel sample was submitted to a heat treatment to obtain a bainític structure. It was heated at 850 °C for 30 minutes and after that, cooled at 300 °C for 60 minutes. Afterwards two types of surface treatments have been employed: (a) using low-power laser CO2 (125 W) for introducing carbon into the surface and (b) plasma nitriding at a temperature of 500° C for 3 hours. After surface treatment, the metallographic preparation was carried out and the observations with optical and electronic microscopy have been made. The analysis of the coating showed an increase in the hardness of layer formed on the surface, mainly, among the nitriding layers. The mechanical properties were analyzed using tensile and fatigue tests. The results showed that the mechanical properties in tensile tests were strongly affected by the bainitic microstructure. The steel that received the nitriding surface by plasma treatment showed better fatigue behavior. The results are very promising because the layer formed on steel surface, in addition to improving the fatigue life, still improves protection against corrosion and wear.

scholarly journals Effect of Quenching and Partitioning Temperatures in the Q-P Process on the Properties of AHSS with Various Amounts of Manganese and Silicon

2012 ◽  
Vol 706-709 ◽  
pp. 2734-2739 ◽  
Author(s):  
Hana Jirková ◽  
Ludmila Kučerová ◽  
Bohuslav Mašek
Keyword(s):  
Tensile Strength ◽  
Retained Austenite ◽  
Isothermal Holding ◽  
Bainitic Ferrite ◽  
High Strength Steels ◽  
High Strength ◽  
Experimental Program ◽  
Quenching Temperature ◽  
Quenching And Partitioning ◽  
Advanced High Strength Steels

The use of the combined influence of retained austenite and bainitic ferrite to improve strength and ductility has been known for many years from the treatment of multiphase steels. Recently, the very fine films of retained austenite along the martensitic laths have also become the centre of attention. This treatment is called the Q-P process (quenching and partitioning). In this experimental program the quenching temperature and the isothermal holding temperature for diffusion carbon distribution for three advanced high strength steels with carbon content of 0.43 % was examined. The alloying strategies have a different content of manganese and silicon, which leads to various martensite start and finish temperatures. The model treatment was carried out using a thermomechanical simulator. Tested regimes resulted in a tensile strength of over 2000MPa with a ductility of above 14 %. The increase of the partitioning temperature influenced the intensity of martensite tempering and caused the decrease of tensile strength by 400MPa down to 1600MPa and at the same time more than 10 % growth of ductility occurred, increasing it to more than 20%.

Application of Quenching-Partitioning-Tempering Process in Hot Rolled Plate Fabrication

2010 ◽  
Vol 654-656 ◽  
pp. 82-85 ◽  
Author(s):  
Shu Zhou ◽  
Ying Wang ◽  
Nai Lu Chen ◽  
Yong Hua Rong ◽  
Jian Feng Gu
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Significant Fraction ◽  
Rolled Plate ◽  
Quenching And Partitioning ◽  
Good Ductility ◽  
Hot Rolled ◽  
Rolled Plates

The quenching-partitioning-tempering (Q-P-T) process, based on the quenching and partitioning (Q&P) treatment, has been proposed for producing high strength steels containing significant fraction of film-like retained austenite and controlled amount of fine martensite laths. In this study, a set of Q-P-T processes for C-Mn-Si-Ni-Nb hot rolled plates are designed and realized. The steels with Q-P-T processes present a combination of high strength and relatively good ductility. The origin of such mechanical properties is revealed by microstructure characterization.

Tensile properties of the FFF-processed thermoplastic polyurethane (TPU) elastomer

2021 ◽  
Author(s):  
Budi Arifvianto ◽  
Teguh Nur Iman ◽  
Benidiktus Tulung Prayoga ◽  
Rini Dharmastiti ◽  
Urip Agus Salim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Low Cost ◽  
Thermoplastic Polyurethane ◽  
High Strength ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Fused Filament Fabrication ◽  
Raster Angle ◽  
Manufacturing Techniques

Abstract Fused filament fabrication (FFF) has become one of the most popular, practical, and low-cost additive manufacturing techniques for fabricating geometrically-complex thermoplastic polyurethane (TPU) elastomer. However, there are still some uncertainties concerning the relationship between several operating parameters applied in this technique and the mechanical properties of the processed material. In this research, the influences of extruder temperature and raster orientation on the mechanical properties of the FFF-processed TPU elastomer were studied. A series of uniaxial tensile tests was carried out to determine tensile strength, strain, and elastic modulus of TPU elastomer that had been printed with various extruder temperatures, i.e., 190–230 °C, and raster angles, i.e., 0–90°. Thermal and chemical characterizations were also conducted to support the analysis in this research. The results obviously showed the ductile and elastic characteristics of the FFF-processed TPU, with specific tensile strength and strain that could reach up to 39 MPa and 600%, respectively. The failure mechanisms operating on the FFF-processed TPU and the result of stress analysis by using the developed Mohr’s circle are also discussed in this paper. In conclusion, the extrusion temperature of 200 °C and raster angle of 0° could be preferred to be applied in the FFF process to achieve high strength and ductile TPU elastomer.

scholarly journals Effect of Intercritical Annealing and Austempering on the Microstructure and Mechanical Properties of a High Silicon Manganese Steel

Metals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1448 ◽  
Author(s):  
Mattia Franceschi ◽  
Luca Pezzato ◽  
Claudio Gennari ◽  
Alberto Fabrizi ◽  
Marina Polyakova ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Intercritical Annealing ◽  
High Strength ◽  
Xrd Analysis ◽  
Tensile Tests ◽  
Manganese Steel ◽  
Microstructure And Mechanical Properties ◽  
Martensitic Microstructure ◽  
Steel Grades ◽  
High Silicon

High Silicon Austempered steels (AHSS) are materials of great interest due to their excellent combination of high strength, ductility, toughness, and limited costs. These steel grades are characterized by a microstructure consisting of ferrite and bainite, accompanied by a high quantity retained austenite (RA). The aim of this study is to analyze the effect of an innovative heat treatment, consisting of intercritical annealing at 780 °C and austempering at 400 °C for 30 min, on the microstructure and mechanical properties of a novel high silicon steel (0.43C-3.26Si-2.72Mn wt.%). The microstructure was characterized by optical and electron microscopy and XRD analysis. Hardness and tensile tests were performed. A multiphase ferritic-martensitic microstructure was obtained. A hardness of 426 HV and a tensile strength of 1650 MPa were measured, with an elongation of 4.5%. The results were compared with those ones obtained with annealing and Q&T treatments.

Microstructure and Mechanical Properties of High Strength Alloyed Steel for Aerospace Application

2018 ◽  
Vol 284 ◽  
pp. 351-356 ◽  
Author(s):  
Mikhail V. Maisuradze ◽  
Maksim A. Ryzhkov
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
High Strength ◽  
Single Stage ◽  
The Novel ◽  
Tempering Temperature ◽  
Quenching And Partitioning ◽  
Aerospace Application ◽  
Cooling Conditions ◽  
Quenching And Tempering

The high strength aerospace steel alloyed with Cr, Mn, Si, Ni, W and Mo was studied. The austenite transformations under continuous cooling conditions were investigated using the dilatometer analysis at the cooling rates 0.1...30 °C/s. The mechanical properties of the studied steel were determined after the conventional quenching and tempering heat treatment. The dependences of the mechanical properties on the tempering temperature were obtained. The novel quenching and partitioning heat treatment was applied to the steel under consideration. The microstructure and the mechanical properties were studied after three different modes of the quenching and partitioning (QP) treatment: single-stage QP, two-stage QP and single-stage QP with subsequent tempering (QPT).

Sign in / Sign up

Export Citation Format

Share Document