scholarly journals Analisis Kesehatan Dan Keselamatan Kerja Menggunakan Failure Mode And Effect Analysis Di PT. XYZ

2021 ◽  
Vol 23 (1) ◽  
pp. 46-58
Author(s):  
Muhammad Ramadan ◽  
Sukanta Sukanta ◽  
Risma Fitriani
Keyword(s):  
Occupational Health ◽  
Production Process ◽  
Health And Safety ◽  
Occupational Health And Safety ◽  
Risk Priority Number ◽  
Effect Analysis ◽  
Fmea Method ◽  
Prime Condition ◽  
A Company

Occupational Health and Safety (OHS) is important to maintain and improve so that the quality of human resources in the company is always in prime condition. Every company has a different level or level of Occupational Health and Safety (OHS). PT. XYZ is a company that uses corrosive materials, therefore Occupational Health and Safety (OHS) analyst at PT XYZ is needed. The Occupational Health and Safety (OHS) analysis carried out in this study used the FMEA method to determine which part of the production process had Occupational Health and Safety (OHS) that needed repair the most. From the research results, it was found that the highest Risk Priority Number (RPN) value was the pickling and degreasing production process.

scholarly journals Risk analysis of production process for food SMEs using FMEA method: a case study

2021 ◽  
Vol 331 ◽  
pp. 02010
Author(s):  
Prima Fithri ◽  
Muhammad Rafi ◽  
Pawenary ◽  
A. S. Prabuwono
Keyword(s):  
Human Resources ◽  
Production Process ◽  
Critical Value ◽  
Risk Priority Number ◽  
Effect Analysis ◽  
Increase Productivity ◽  
Fmea Method ◽  
Bread Production ◽  
A Company

The increasing development of the industry makes every industry have to compete with other competitors to gain an edge. The advantages of competition are influenced by several factors, one of which is good human resource management. Where if a company has good human resources, it will increase profits indirectly and can increase productivity. This research discusses case studies about the potential dangers of IKM Heppy Bakery’s potential dangers that can harm workers in bread production. The method used is Failure Mode And Effect Analysis (FMEA). Later, the data will be filled and given a rating distinguished into three parts: severity, occurrence, and detection. The data were obtained through questionnaires given to 3 workers at IKM Heppy Bakery and filled in rating values based on the provisions that have been given to the questionnaire. This Value helps determine the Risk Priority Number (RPN) obtained from multiplication between severity, occurrence, and detection. After processing the RPN multiplication data, the highest RPN value was obtained by 193 with the danger factor of the operator overheating and dehydrating due to high temperatures. Furthermore, the calculation of critical Value was obtained by 109. Based on the critical Value obtained seven hazard factors above the critical value, these seven hazard factors need to be improved so that workers do not avoid accidents when conducting the production process.

PEMANFAATAN PERALATAN KESELAMATAN DAN KESEHATAN KERJA (K3) PADA PRAKTIKUM PROSES PRODUKSI

2020 ◽  
Vol 1 (2) ◽  
pp. 64-70
Author(s):  
Rezky Fajar Ramadhan
Keyword(s):  
Data Collection ◽  
Occupational Health ◽  
Engineering Education ◽  
Production Process ◽  
Mechanical Engineering ◽  
Health And Safety ◽  
Occupational Health And Safety ◽  
Education Students ◽  
Descriptive Data

Abstrak: Tujuan penelitian ini adalah untuk mendeskripsikan penggunaan peralatan Kesehatan dan Keselamatan Kerja (K3) pada Mata Kuliah Praktikum Proses Produksi mahasiswa Pendidikan Teknik Mesin, Universitas Palangka Raya. Jenis penelitian ini adalah deskriptif. Teknik pengumpulan data menggunakan teknik angket dan dokumentasi. Objek penelitian adalah seluruh mahasiswa Pendidikan Teknik Mesin, Universitas Palangka Raya yang memprogramkan Mata Kuliah Praktikum Proses Produksi. Hasil penelitian ini menunjukkan bahwa 43% mahasiswa menyatakan sangat baik dan 57% mahasiswa menyatakan baik penggunaan peralatan K3 pada Mata Kuliah Praktikum Proses Produksi. Sehingga, disimpulkan bahwa penerapan K3 dapat mendukung pelaksanaan praktikum proses produksi.   Abstract: The purpose of this study was to describe the use of Occupational Health and Safety (OHS) equipment in the Production Process Practicum Subject of Mechanical Engineering Education students, Palangka Raya University. This type of research was descriptive. Data collection techniques used questionnaires and documentation. The object of research was all students of Mechanical Engineering Education, Palangkaraya University who programed Production Process Practicum Subjects. The results of this study indicate that 43% of students stated very well and 57% of students stated good use of OHS equipment in the Production Process Practicum Course. Thus, it was concluded that the application of OHS can support the implementation of practicum in the production process.

scholarly journals Penggunaan Metode Heart Dan JSA Sebagai Upaya Pengurangan Human Error Pada Kecelakaan Kerja Di Departemen Produksi

2017 ◽  
Vol 17 (1) ◽  
pp. 1
Author(s):  
Faris Rohmawan ◽  
Dian Palupi Restuputri
Keyword(s):  
Occupational Health ◽  
Production Process ◽  
Human Error ◽  
Raw Materials ◽  
Health And Safety ◽  
Occupational Accidents ◽  
Occupational Accident ◽  
Operational Procedure ◽  
Additional Equipment ◽  
A Company

Occupational health and safety is very important point for a company. CV. XYZ is a company that produces paving and have problem about the occupational accident. There are 4 production procceses that can be couse occupational accidents, which is taking raw materials procces, stirring batter, forming and drying. This case must be analyzed using HEART and JSA method as evaluating effort for occupational accident. The results of HEART method analysing imply that HEP value 0,8632is the most dangerous occupational, that is forpicking gravel from cement mixer machine. After known the value of HEP afterward analyzed using JSA method. The goal is as improvement to occupational accident in the production process in order can be reduced. The result of JSA method analysing are improvement suggestion such us levying mask, hat, design of additional components for machine, additional equipment for pallet and hand pallet, and assigning standart operational procedure.

scholarly journals Analisis Pengaruh Efektivitas Penerapan Sistem Manajemen Keselamatan dan Kesehatan Kerja (SMK3) Terhadap Produktivitas Kerja Karyawan (Studi Kasus Plant 11 PT Indocement Tunggal Prakarsa, Tbk Citeureup)

2016 ◽  
Vol 1 (2) ◽  
pp. 80
Author(s):  
Rini Riestiany ◽  
Ratih Maria Dhewi ◽  
Sjafri Mangkuprawira
Keyword(s):  
Occupational Health ◽  
Safety Assessment ◽  
Health And Safety ◽  
Secondary Data ◽  
Occupational Health And Safety ◽  
Safety Training ◽  
Quality Of Work Life ◽  
Work Accident ◽  
Cement Factories

<p><em>Employee is an important resource to have production process in a big factory. Factory couldn’t operate without employee. To protect their employees, the leader makes a policy like occupational health and safety. This policy for protect their employee from risk of bad accident and illness that causes of work. Bad accident can strike employee anywhere and anytime so this cases must to have a special attention. So, the leader, government, and management must pay attention to this risk.  Work accident leaning influence to manpower productivity because quality of work life and guarantee of occupational health and safety influence manpower productivity. PT Indocement Tunggal Prakarsa, Tbk is one of the biggest cement factories in Indonesia. This factory has applicated occupational health and safety assessment base on Permenaker No. 05/MEN/1996 and OHSAS 18001. Occupational health and safety effectiveness can describe by six aspect based on Miner Theory. That theory are safety training,</em><em> </em><em>safety publication, control to work</em><em> </em><em>environment, inspection and discipline, improvement awareness of occupational health and safety, report and statistic of occupational health and safety. Five aspect of Theory Miner, can describe by employee perspective, even report and statistic of occupational health and safety can describe by secondary data from Safety Department and Management Representative of PT ITP.</em></p>

scholarly journals THE EFFECTIVENESS OF THE OCCUPATIONAL HEALTH AND SAFETY ASSESSMENT SERIES 18001:2007 PT. SURYA BESINDO SAKTI

2020 ◽  
Vol 3 (3) ◽  
pp. 114
Author(s):  
Sudarman Subhi ◽  
Catur Septiawan
Keyword(s):  
Occupational Health ◽  
Work Environment ◽  
Safety Assessment ◽  
Health Workers ◽  
Health And Safety ◽  
Occupational Health And Safety ◽  
Safety And Health ◽  
Minimum Requirements ◽  
A Company ◽  
Research Type

Background: OHSAS 18001:2007 is management system of occupational health and safety international standard which includes the structure of the organization, the planning activities, responsibility, procedure, the process and resources to manage K3 .OHSAS have a purpose for protection against the workers from unwanted things arising from work environment, or activity work itself, it have an impact on safety and health workers, and so as not to cause much loss for from accidents work have image bad a company that can lower image company. Purpose: This study aimed to understand the effectiveness of the occupational health and safety assessment series (OHSAS) 18001:2007 in PT. Surya Besindo Sakti. Methods: The research used descriptive qualitative research type and design. Test the validity of data using technique triagulation method. Result: PT. Surya Besindo Sakti still meets the minimum requirements of the application of Occupational Health and Safety Assessment Series (OHSAS) 18001: 2007. With findings of minor incompatibilities 6 and 1 OFI (Opportunity For Improvement) findings. Conclusion: The company is expected to continue to commit to run the Occupational Health and Safety Assessment Series (OHSAS) 18001: 2007 for corporate vision and mission to be achieved, objective must be monitored its achievement every month by each department and ensure all procedures used in the company reviewed and implemented consistently.

scholarly journals Methodological Challenges in the Economic Evaluation of Occupational Health and Safety Programmes

2018 ◽  
Vol 15 (11) ◽  
pp. 2606 ◽  
Author(s):  
Jonas Steel ◽  
Lode Godderis ◽  
Jeroen Luyten
Keyword(s):  
Economic Evaluation ◽  
Occupational Health ◽  
Health And Safety ◽  
Occupational Health And Safety ◽  
Evaluation Methods ◽  
Economic Evaluations ◽  
Advantages And Disadvantages ◽  
Reputation Effects ◽  
Future Work

An emerging issue in occupational health and safety (OHS) is that interventions increasingly have to demonstrate that they offer sufficient value for money. To this end, the last decennia have seen more and more economic evaluation methods being employed in this field. However, several recent publications have indicated that many of the published studies suffer from important shortcomings. This paper aims to highlight difficulties in assessing the value of OHS by use of current economic evaluation methods. First, a summary framework presents an overview of the costs and benefits relevant for OHS interventions. Next, three elements from this framework are selected that are at the same time crucial to OHS value, but also challenging to measure and monetise: Effects on worker productivity, ‘intangible’ benefits, such as reputation effects, and the influence of the broader legal–fiscal context in which an intervention takes place. The following sections then discuss the following research questions for each of these elements: Why is it difficult to exclude these factors from OHS economic evaluations? Why do they pose a challenge to the quality of economic evaluations in OHS? How can they be included, and what are the known advantages and disadvantages of the methods to measure these factors? Future work should investigate (and standardise) better methods to include these elements.

Sign in / Sign up

Export Citation Format

Share Document