scholarly journals Dynamic analysis of vertical stormwater storage systems

2021 ◽  
Author(s):  
Kay Taegyeong Kang
Keyword(s):  
Storage Systems ◽  
Storage System ◽  
Experimental Result ◽  
Scale Model ◽  
Rapid Rise ◽  
Flow Oscillation ◽  
Drop Shaft ◽  
Physical Scale ◽  
Rain Events ◽  
Entrapped Air

A below-grade vertical stormwater storage system is one of the solutions to reduce the volume of sewer overflows released into the environment. The system is submerged most of the time during filling, which can result in hydraulic problems. This research intent to provide some insight on potential hydraulic problems that can occur in a vertical storage system during intense rain events. An experimental study was conducted using a physical scale model that consists of two vertical storage shafts, a horizontal tunnel and an inflow drop shaft. The results showed that both entrapped air in the system and mass flow oscillation in the system can cause a rapid rise of water level, or a geyser, at the drop shaft. The predictions of a modified version of HAMMER compared well with the experimental result while the InfoWorks CS model was unable to simulate vertical momentum in the drop shaft.

scholarly journals Dynamic analysis of vertical stormwater storage systems

2021 ◽  
Author(s):  
Kay Taegyeong Kang
Keyword(s):  
Storage Systems ◽  
Storage System ◽  
Experimental Result ◽  
Scale Model ◽  
Rapid Rise ◽  
Flow Oscillation ◽  
Drop Shaft ◽  
Physical Scale ◽  
Rain Events ◽  
Entrapped Air

A below-grade vertical stormwater storage system is one of the solutions to reduce the volume of sewer overflows released into the environment. The system is submerged most of the time during filling, which can result in hydraulic problems. This research intent to provide some insight on potential hydraulic problems that can occur in a vertical storage system during intense rain events. An experimental study was conducted using a physical scale model that consists of two vertical storage shafts, a horizontal tunnel and an inflow drop shaft. The results showed that both entrapped air in the system and mass flow oscillation in the system can cause a rapid rise of water level, or a geyser, at the drop shaft. The predictions of a modified version of HAMMER compared well with the experimental result while the InfoWorks CS model was unable to simulate vertical momentum in the drop shaft.

Modeling an Energy Storage System Based on a Hybrid Renewable Energy System in Stand-alone Applications

2017 ◽  
Vol 68 (11) ◽  
pp. 2641-2645
Author(s):  
Alexandru Ciocan ◽  
Ovidiu Mihai Balan ◽  
Mihaela Ramona Buga ◽  
Tudor Prisecaru ◽  
Mohand Tazerout
Keyword(s):  
Renewable Energy ◽  
Energy Storage ◽  
Storage Systems ◽  
Renewable Energy Sources ◽  
Storage System ◽  
Energy Storage System ◽  
Compressed Air ◽  
Energy Sources ◽  
Energy Storage Systems ◽  
Hybrid Renewable Energy System

The current paper presents an energy storage system that stores the excessive energy, provided by a hybrid system of renewable energy sources, in the form of compressed air and thermal heat. Using energy storage systems together with renewable energy sources represents a major challenge that could ensure the transition to a viable economic future and a decarbonized economy. Thermodynamic calculations are conducted to investigate the performance of such systems by using Matlab simulation tools. The results indicate the values of primary and global efficiencies for various operating scenarios for the energy storage systems which use compressed air as medium storage, and shows that these could be very effective systems, proving the possibility to supply to the final user three types of energy: electricity, heat and cold function of his needs.

scholarly journals Multiphasic Study of Fluid-Dynamics and the Thermal Behavior of a Steel Ladle during Bottom Gas Injection Using the Eulerian Model

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1082
Author(s):  
Antonio Urióstegui-Hernández ◽  
Pedro Garnica-González ◽  
José Ángel Ramos-Banderas ◽  
Constantin Alberto Hernández-Bocanegra ◽  
Gildardo Solorio-Díaz
Keyword(s):  
Heat Exchange ◽  
Thermal Behavior ◽  
Gas Flow ◽  
Fluid Dynamic ◽  
Steel Slag ◽  
Scale Model ◽  
Discrete Ordinates ◽  
Transfer Model ◽  
Steel Ladle ◽  
Physical Scale

In this work, the fluid dynamic and thermal behavior of steel was analyzed during argon gas stirring in a 140-t refining ladle. The Eulerian multiphase mathematical model was used in conjunction with the discrete ordinates (DO) thermal radiation model in a steel-slag-argon system. The model was validated by particle image velocimetry (PIV) and the analysis of the opening of the oil layer in a physical scale model. The effect of Al2O3 and Mg-C as a refractory in the walls was studied, and the Ranz-Marshall and Tomiyama models were compared to determine the heat exchange coefficient. The results indicated that there were no significant differences between these heat exchange models; likewise, the radiation heat transfer model adequately simulated the thermal behavior according to plant measurements, finding a thermal homogenization time of the steel of 2.5 min for a gas flow of 0.45 Nm3·min−1. Finally, both types of refractory kept the temperature of the steel within the ranges recommended in the plant; however, the use of Al2O3 had better heat retention, which would favor refining operations.

A facile new modified method for the preparation of a new cerium-doped lanthanium cuperate perovskite energy storage system using nanotechnology

2021 ◽  
Author(s):  
Mervette El Batouti ◽  
H. A. Fetouh
Keyword(s):  
Solar Cells ◽  
Energy Storage ◽  
Dielectric Loss ◽  
Storage Systems ◽  
Low Cost ◽  
Storage System ◽  
Energy Storage System ◽  
Solar Ponds ◽  
Modified Method ◽  
Ferroelectric Perovskite

New ferroelectric perovskite sample: excellent dielectric, negligible dielectric loss for energy storage systems such as solar cells, solar ponds, and thermal collectors has been prepared at low cost using nanotechnology.

scholarly journals Emissions Effects of Energy Storage for Frequency Regulation: Comparing Battery and Flywheel Storage to Natural Gas

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 549
Author(s):  
Eric Pareis ◽  
Eric Hittinger
Keyword(s):  
Energy Storage ◽  
Natural Gas ◽  
Fossil Fuels ◽  
Storage Systems ◽  
Storage System ◽  
The United States ◽  
Frequency Regulation ◽  
So2 Emissions ◽  
Gas Generation ◽  
Electrical Generation

With an increase in renewable energy generation in the United States, there is a growing need for more frequency regulation to ensure the stability of the electric grid. Fast ramping natural gas plants are often used for frequency regulation, but this creates emissions associated with the burning of fossil fuels. Energy storage systems (ESSs), such as batteries and flywheels, provide an alternative frequency regulation service. However, the efficiency losses of charging and discharging a storage system cause additional electrical generation requirements and associated emissions. There is not a good understanding of these indirect emissions from charging and discharging ESSs in the literature, with most sources stating that ESSs for frequency regulation have lower emissions, without quantification of these emissions. We created a model to estimate three types of emissions (CO2, NOX, and SO2) from ESSs providing frequency regulation, and compare them to emissions from a natural gas plant providing the same service. When the natural gas plant is credited for the generated electricity, storage systems have 33% to 68% lower CO2 emissions than the gas turbine, depending on the US eGRID subregion, but higher NOX and SO2 emissions. However, different plausible assumptions about the framing of the analysis can make ESSs a worse choice so the true difference depends on the nature of the substitution between storage and natural gas generation.

scholarly journals Roughness Lengths for Momentum and Heat Derived from Outdoor Urban Scale Models

2007 ◽  
Vol 46 (7) ◽  
pp. 1067-1079 ◽  
Author(s):  
M. Kanda ◽  
M. Kanega ◽  
T. Kawai ◽  
R. Moriwaki ◽  
H. Sugawara
Keyword(s):  
Wind Direction ◽  
Roughness Length ◽  
Scale Dependence ◽  
Scale Model ◽  
Small Scale ◽  
Physical Scale ◽  
Scale Models ◽  
Roughness Lengths ◽  
Urban Sites ◽  
Obstacle Height

Abstract Urban climate experimental results from the Comprehensive Outdoor Scale Model (COSMO) were used to estimate roughness lengths for momentum and heat. Two different physical scale models were used to investigate the scale dependence of the roughness lengths; the large scale model included an aligned array of 1.5-m concrete cubes, and the small scale model had a geometrically similar array of 0.15-m concrete cubes. Only turbulent data from the unstable boundary layers were considered. The roughness length for momentum relative to the obstacle height was dependent on wind direction, but the scale dependence was not evident. Estimated values agreed well with a conventional morphometric relationship. The logarithm of the roughness length for heat relative to the obstacle height depended on the scale but was insensitive to wind direction. COSMO data were used successfully to regress a theoretical relationship between κB−1, the logarithmic ratio of roughness length for momentum to heat, and Re*, the roughness Reynolds number. Values of κB−1 associated with Re* for three different urban sites from previous field experiments were intercompared. A surprising finding was that, even though surface geometry differed from site to site, the regressed function agreed with data from the three urban sites as well as with the COSMO data. Field data showed that κB−1 values decreased as the areal fraction of vegetation increased. The observed dependency of the bulk transfer coefficient on atmospheric stability in the COSMO data could be reproduced using the regressed function of Re* and κB−1, together with a Monin–Obukhov similarity framework.

scholarly journals Numerical Study of Pressure Attenuation Effect on Tunnel Structures Subjected to Blast Loads

2021 ◽  
Vol 11 (12) ◽  
pp. 5646
Author(s):  
Cheng-Wei Hung ◽  
Ying-Kuan Tsai ◽  
Tai-An Chen ◽  
Hsin-Hung Lai ◽  
Pin-Wen Wu
Keyword(s):  
Numerical Simulation ◽  
Orifice Plate ◽  
Experimental Result ◽  
Scale Model ◽  
Pressure Reduction ◽  
Expansion Chamber ◽  
Pressure Relief ◽  
Attenuation Effect ◽  
The One ◽  
Better Than

This study used experimental and numerical simulation methods to discuss the attenuation mechanism of a blast inside a tunnel for different forms of a tunnel pressure reduction module under the condition of a tunnel near-field explosion. In terms of the experiment, a small-scale model was used for the explosion experiments of a tunnel pressure reduction module (expansion chamber, one-pressure relief orifice plate, double-pressure relief orifice plate). In the numerical simulation, the pressure transfer effect was evaluated using the ALE fluid–solid coupling and mapping technique. The findings showed that the pressure attenuation model changed the tunnel section to diffuse, reduce, or detour the pressure transfer, indicating the blast attenuation effect. In terms of the effect of blast attenuation, the double-pressure relief orifice plate was better than the one-pressure relief orifice plate, and the single-pressure relief orifice plate was better than the expansion chamber. The expansion chamber attenuated the blast by 30%, the one-pressure relief orifice plate attenuated the blast by 51%, and the double-pressure relief orifice plate attenuated the blast by 82%. The blast attenuation trend of the numerical simulation result generally matched that of the experimental result. The results of this study can provide a reference for future protective designs and reinforce the U.S. Force regulations.

Solid Media Thermal Storage Development and Analysis of Modular Storage Operation Concepts for Parabolic Trough Power Plants

2007 ◽  
Vol 130 (1) ◽  
Author(s):  
Doerte Laing ◽  
Wolf-Dieter Steinmann ◽  
Michael Fiß ◽  
Rainer Tamme ◽  
Thomas Brand ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Power Plants ◽  
Heat Storage ◽  
Storage Systems ◽  
Storage System ◽  
Sensible Heat ◽  
Economic Optimization ◽  
Parabolic Trough ◽  
Solid Media ◽  
Exergetic Analysis

Cost-effective integrated storage systems are important components for the accelerated market penetration of solarthermal power plants. Besides extended utilization of the power block, the main benefits of storage systems are improved efficiency of components, and facilitated integration into the electrical grids. For parabolic trough power plants using synthetic oil as the heat transfer medium, the application of solid media sensible heat storage is an attractive option in terms of investment and maintenance costs. For commercial oil trough technology, a solid media sensible heat storage system was developed and tested. One focus of the project was the cost reduction of the heat exchanger; the second focus lies in the energetic and exergetic analysis of modular storage operation concepts, including a cost assessment of these concepts. The results show that technically there are various interesting ways to improve storage performance. However, these efforts do not improve the economical aspect. Therefore, the tube register with straight parallel tubes without additional structures to enhance heat transfer has been identified as the best option concerning manufacturing aspects and investment costs. The results of the energetic and exergetic analysis of modular storage integration and operation concepts show a significant potential for economic optimization. An increase of more than 100% in storage capacity or a reduction of more than a factor of 2 in storage size and therefore investment cost for the storage system was calculated. A complete economical analysis, including the additional costs for this concept on the solar field piping and control, still has to be performed.

AN EXPERIMENTAL STUDY ON THE RELATIVE MOTIONS BETWEEN A FLOATING HARBOUR TRANSHIPPER AND A FEEDER VESSEL IN REGULAR WAVES

2021 ◽  
Vol 154 (A2) ◽  
Author(s):  
G J Macfarlane ◽  
T Lilienthal ◽  
R J Ballantyne ◽  
S Ballantyne
Keyword(s):  
Open Water ◽  
Scale Model ◽  
Regular Waves ◽  
Inclement Weather ◽  
Port Operations ◽  
Physical Scale ◽  
Feeder Vessel ◽  
Primary Advantage ◽  
Exposed Location ◽  
Relative Motions

The Floating Harbour Transhipper (FHT) is a pioneering logistics solution that was designed to meet the growing demands for coastal transhipment in the mining sector as well as commercial port operations. The primary advantage of the FHT system is that it can reduce transhipment delays caused by inclement weather, by reducing relative motions between the FHT and feeder vessel. The feeder is sheltered when inside the FHT well dock when compared to the more exposed location when a feeder is in a traditional side-by-side mooring arrangement. This paper discusses previously published studies into the relative motions of vessels engaged in side-by-side mooring arrangements and also presents details and results from a series of physical scale model experiments. In these experiments, both side-by-side and aft well dock mooring arrangements are investigated. The results provide strong evidence that the FHT well dock concept can significantly reduce the heave, pitch and roll motions of feeder vessels when transhipping in open seas – this being the cornerstone of any successful open water transhipment operation.

Cooperative Sequence Clustering and Decoding for DNA Storage System with Fountain Codes

2021 ◽  
Author(s):  
Jaeho Jeong ◽  
Seong-Joon Park ◽  
Jae-Won Kim ◽  
Jong-Seon No ◽  
Ha Hyeon Jeon ◽  
...  
Keyword(s):  
Hamming Distance ◽  
Storage Systems ◽  
Storage System ◽  
Data Retrieval ◽  
Illumina Miseq ◽  
Error Correcting Codes ◽  
Read Length ◽  
Sequence Coverage ◽  
Source Codes ◽  
Dna Storage

Abstract Motivation In DNA storage systems, there are tradeoffs between writing and reading costs. Increasing the code rate of error-correcting codes may save writing cost, but it will need more sequence reads for data retrieval. There is potentially a way to improve sequencing and decoding processes in such a way that the reading cost induced by this tradeoff is reduced without increasing the writing cost. In past researches, clustering, alignment, and decoding processes were considered as separate stages but we believe that using the information from all these processes together may improve decoding performance. Actual experiments of DNA synthesis and sequencing should be performed because simulations cannot be relied on to cover all error possibilities in practical circumstances. Results For DNA storage systems using fountain code and Reed-Solomon (RS) code, we introduce several techniques to improve the decoding performance. We designed the decoding process focusing on the cooperation of key components: Hamming-distance based clustering, discarding of abnormal sequence reads, RS error correction as well as detection, and quality score-based ordering of sequences. We synthesized 513.6KB data into DNA oligo pools and sequenced this data successfully with Illumina MiSeq instrument. Compared to Erlich’s research, the proposed decoding method additionally incorporates sequence reads with minor errors which had been discarded before, and thuswas able to make use of 10.6–11.9% more sequence reads from the same sequencing environment, this resulted in 6.5–8.9% reduction in the reading cost. Channel characteristics including sequence coverage and read-length distributions are provided as well. Availability The raw data files and the source codes of our experiments are available at: https://github.com/jhjeong0702/dna-storage.

Sign in / Sign up

Export Citation Format

Share Document