Activated carbon from potassium hydroxide spent liquor lignin using phosphoric acid

TAPPI Journal ◽  
2018 ◽  
Vol 17 (02) ◽  
pp. 63-69 ◽  
Author(s):  
Mamon Sarkar ◽  
Chao Tian ◽  
M. Sarwar Jahan
Keyword(s):  
Activated Carbon ◽  
Phosphoric Acid ◽  
Iodine Number ◽  
Surface Area ◽  
Potassium Hydroxide ◽  
Bet Surface Area ◽  
Koh Activation ◽  
Activation Temperature ◽  
Impregnation Ratio ◽  
Spent Liquor

Activated carbon was prepared by phosphoric acid (H3PO4) activation of potassium hydroxide (KOH) pulping spent liquor lignin from rice straw and compared with KOH hydroxide activation. The process parameters, such as impregnation ratio, activation temperature, and activation time were varied and their effects on the yield of activated carbon and iodine number were studied. The activated carbon prepared by H3PO4 at 800°C for 60 min at an impregnation ratio of 2.5 reached a Brunauer-Emmett-Teller (BET) surface area of 1063 m2/g, including pore diameter of 14.4 nm, iodine number of 525 mg/g, and yield of 49.2%. Yield and BET surface area in KOH activation was much lower than that of H3PO4.

Physicochemical Properties of Carbons Prepared from Physic Nut Waste by Phosphoric Acid and Potassium Hydroxide Activations

2007 ◽  
Vol 561-565 ◽  
pp. 1719-1722 ◽  
Author(s):  
Chiravoot Pechyen ◽  
Duangdao Aht-Ong ◽  
Duangduen Atong ◽  
Viboon Sricharoenchaikul
Keyword(s):  
Activated Carbon ◽  
Phosphoric Acid ◽  
Physicochemical Properties ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Potassium Hydroxide ◽  
Bet Surface Area ◽  
Physic Nut ◽  
Monolayer Adsorption ◽  
Adsorption Data

Char derived from pyrolysis of physic nut waste at 400-800°C was used for the preparation of activated carbon by chemical impregnation of phosphoric acid and potassium hydroxide. The original char exhibited the BET surface area in the range of 120-250 m2·g-1. The surface area increased to 480 and 532 m2·g-1 when activated with H3PO4 and KOH, respectively. Equilibrium adsorption data was found to be best represented by the Langmuir isotherm with maximum monolayer adsorption capacity of 560.13 mg·g-1 at 30°C. The adsorption capacity of the physic nut residue activated carbon was comparable to commercial activated carbon.

Preparation and Characterization of Activated Carbon from Reedy Grass Leaves by Chemical Activation with KOH

2014 ◽  
Vol 881-883 ◽  
pp. 579-583 ◽  
Author(s):  
Ling Zhi Chen ◽  
Dong Xu Miao ◽  
Xiao Jie Feng ◽  
Jian Zhong Xu
Keyword(s):  
Iodine Number ◽  
Surface Area ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Weight Ratio ◽  
Raw Material ◽  
Bet Surface Area ◽  
Activation Temperature ◽  
Impregnation Ratio ◽  
Dta Analysis

Activated carbons (AC) were produced by chemical activation with potassium hydroxide (KOH) at 800°C from chars that were carbonized from reedy grass leaves at 450°C in N2atmosphere. The effects of the weight ratio of KOH/char ( impregnation ratio), activation temperature and duration time were examined. Adsorption capacity was demonstrated with iodine number. BET surface area, pore volume and pore size of activated carbons were characterized by N2adsorption isotherms. The maximum surface area and iodine number of the AC was 1100 m2/g and 1080 mg/g produced at 800°C for2h and impregnation ratio is 4:1.The characteristics of activated carbons were determined by Infrared spectroscopy (FT-IR) and X-ray diffraction (XRD). Thermal gravimetry (TG/DTA) analysis of raw material was carried out.

scholarly journals Fine Activated Carbon from Rubber Fruit Shell Prepared by Using ZnCl2 and KOH Activation

2021 ◽  
Vol 11 (9) ◽  
pp. 3994
Author(s):  
Suhdi ◽  
Sheng-Chang Wang
Keyword(s):  
Activated Carbon ◽  
Carbon Content ◽  
Surface Area ◽  
Average Pore Size ◽  
Absorption Capacity ◽  
Bet Surface Area ◽  
Koh Activation ◽  
Average Pore ◽  
Impregnation Ratio ◽  
Precursor Material

Fine activated carbon (FAC) is prepared from rubber fruit shells (RFS) using two chemical activating agents (ZnCl2 and KOH) and three impregnation ratios (1:3, 1:4, and 1:5). The Brunauer–Emmett–Teller (BET) results show that for a constant impregnation ratio, the ZnCl2 activating agent yields a higher specific surface area than the KOH agent. In particular, for the maximum impregnation ratio of 1:5, the FAC prepared using ZnCl2 has a BET surface area of 456 m2/g, a nitrogen absorption capacity of 150.38 cm3/g, and an average pore size of 3.44 nm. Moreover, the FAC structure consists of 70.1% mesopores and has a carbon content of 80.05 at.%. Overall, the results confirm that RFS, activated using an appropriate quantity of ZnCl2, provides a cheap, abundant, and highly promising precursor material for the preparation of activated carbon with high carbon content and good adsorption properties

Preparation and TG/DTG, FT-IR, SEM, BET Surface Area, Iodine Number and Methylene Blue Number Analysis of Activated Carbon from Pistachio Shells by Chemical Activation

2017 ◽  
Vol 16 (2) ◽  
Author(s):  
Mustafa Kaya ◽  
Ömer Şahin ◽  
Cafer Saka
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Iodine Number ◽  
Surface Area ◽  
Chemical Activation ◽  
Total Pore Volume ◽  
Bet Surface Area ◽  
Optimum Conditions ◽  
Activation Temperature ◽  
Pistachio Shell

AbstractIn this study, low cost activated carbon was prepared from the pistachio shell by chemical activation with zinc chloride (ZnCl2). The prepared activated carbon was characterized by thermogravimetry (TG) and differential thermal gravimetry (DTG), infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and Brunauer, Emmett and Teller (BET) surface area analyses. Results showed that the activation temperature and impregnation ratio have significant effect on the iodine number of the prepared activated carbon. The optimum conditions for preparing the activated carbon having the highest surface area were found to be an activation temperature of 700 °C, soaking time of 24 h and ZnCl2/ pistachio shell ratio of 50 %. The results showed that the BET surface area, total pore volume, iodine number and methylene blue (MB) number of activated carbon prepared under the optimum conditions were 1108 m2/g, 0.39 cm3/g, 1051 mg/g, 98.48 mg/g, respectively.

scholarly journals Comparative study for adsorption of acidic and basic dyes on activated carbon prepared from date stone by different activation agent

2020 ◽  
Vol 13 (1) ◽  
pp. 12-20
Author(s):  
Azhaar Radhi Jabbar
Keyword(s):  
Activated Carbon ◽  
Phosphoric Acid ◽  
Surface Area ◽  
Zinc Chloride ◽  
Potassium Hydroxide ◽  
Adsorption Process ◽  
Activated Carbons ◽  
Second Order ◽  
Bet Surface Area ◽  
Pseudo Second Order

This research includes a lab scale work to investigate the feasibility of treating waste water which polluted with dyes exhausted from textile factory by using adsorption process. Three type of activated carbon were prepared using locally available waste material (date stone). Chemical activation method  with (zinc chloride, potassium hydroxide, or phosphoric acid) was used  as activators  to  prepared carbon. Firstly, the materials were carbonized at 275 oC for 90 min and then the carbonized materials were treated with (4 molar) solution of acid, base or salt for 24 hour. Finally, these materials were activated at 600 oC for two hours in the presence of nitrogen gas flow. The resulted activated carbons were checked by its (BET) surface area analysis and surface morphology by SEM. The surface area values were (815, 950,600) m2/g for carbon produced from the activation of date  stone by phosphoric acid, potassium hydroxide or zinc chloride respectively. SEM characterizations show that activated carbons that prepared from potassium hydroxide have higher surface area and good adsorption characteristics than that prepared from activation with phosphoric acid or zinc chloride. The  adsorption process was studied using two types of dyes. The first one is acidic (methyl orange) and the other is basic (bismark brown). The adsorption isotherms and kinetics where investigated for both dyes at temperatures (30,40,50,60)oC for concentration  range  equal to (6-16)mg/l.  The  adsorption data of equilibrium were presented by using two common adsorption isotherm equations. The data was fitted fairly well with Langmuir isotherm for both dyes on all types of prepared activated carbons. The kinetic of adsorption was study by using two kinetic equations, pseudo first order and pseudo second order. The result showed the rapid increase in the rate of adsorption at the initial until equilibrium achieved. Pseudo second order model were represent the data very well with confidence level 0.99.

scholarly journals ACTIVATED CARBON FROM DURIAN SEED BY H3PO4 ACTIVATION: PREPARATION AND PORE STRUCTURE CHARACTERIZATION

2010 ◽  
Vol 10 (1) ◽  
pp. 36-40 ◽  
Author(s):  
Amri Ismail ◽  
Hanggara Sudrajat ◽  
Desi Jumbianti
Keyword(s):  
Activated Carbon ◽  
Phosphoric Acid ◽  
Heating Rate ◽  
Surface Area ◽  
Activated Carbons ◽  
Acid Activation ◽  
Activation Temperature ◽  
Impregnation Ratio ◽  
Durio Zibethinus ◽  
Durian Seed

Activated carbons have been produced from the natural biomaterial durian (Durio zibethinus) seed, using phosphoric acid (H3PO4) as the activating agent. The effects of impregnation ratio, activation temperature, heating rate on the carbon surface area, porosity and mass yield are presented. A two step process has been used, the first step was a low temperature impregnation at 150 °C using phosphoric acid and the second step was the carbonization at high temperatures, namely, 600 and 900 °C. The most outstanding carbon with the highest surface area of 2123 m2/g was prepared using an impregnation ratio of 2, an activation temperature of 600 °C for 4 h and a heating rate of 1 °C/min.   Keywords: activated carbon, durian seed, phosphoric acid activation

Effect of Activation Agents on COD Reduction Using Activated Carbon from Agricultural Residue

2020 ◽  
Vol 1010 ◽  
pp. 453-458
Author(s):  
Mohd Zazmiezi Mohd Alias ◽  
Rozidaini Mohd Ghazi ◽  
Nik Raihan Nik Yusoff ◽  
Mohd Hafiz Jamaludin
Keyword(s):  
Activated Carbon ◽  
Phosphoric Acid ◽  
Potassium Hydroxide ◽  
Activated Carbons ◽  
Oxygen Demand ◽  
Koh Activation ◽  
Ftir Analysis ◽  
Agricultural Residue ◽  
Cod Reduction ◽  
Activating Agent

This study investigated the effect of activating agent on activated carbon preparation and potential chemical oxygen demand (COD) reduction using activated carbons (AC) prepared. Zinc chloride, phosphoric acid and potassium hydroxide were utilized in impregnation of bamboo and rice husk. Result of SEM-EDX, FTIR as well as COD reduction were compared and discussed. The SEM displayed highest porosity in AC using KOH activation. FTIR analysis displayed obvious difference for each activation. AC using KOH activation obtained highest COD reduction.

Activated carbon powder derived from cashmere guard hair

2019 ◽  
Vol 50 (5) ◽  
pp. 599-615
Author(s):  
Zhuanyong Zou ◽  
Xin Liu ◽  
Jiahui Ding ◽  
Tanqi Chen ◽  
Xungai Wang
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Carbon Powder ◽  
Guard Hair ◽  
Carbon Yield ◽  
Activation Temperature ◽  
Impregnation Ratio ◽  
Study Results

Converting waste fiber to high value-added carbonaceous materials has been considered as an effective and affordable route in response to the increasing volume of waste fiber in recent year. In this study, we are the first to prepare activated carbon powder derived from cashmere guard hair as a renewable waste protein fiber, using a chemical activation method at different impregnation ratios of K2CO3/cashmere guard hair char and activation temperatures ranging from 400℃ to 600℃. Characterization of the activated carbon powder was carried out by morphology study, specific surface area study, and adsorption study. Results have shown that the increase of the impregnation ratio and the activation temperature created more microporous structure in the activated carbon powder, and then increased the specific surface area of the activated carbon powder as well as the amount of methylene blue adsorbed. However, the carbon yield increases with the increase in the impregnation ratio of K2CO3/cashmere guard hair char and decreases with the increase in the activation temperature. The activated carbon powder, activated by the condition of 1:2 K2CO3/cashmere guard hair char impregnation ratio and 600℃ activation temperature, has a specific surface area of 764.86 m2g−1 and a carbon yield of 14.07 wt%. Compared to the activated carbon powder derived from fine merino wool fibers, the activated carbon powder derived from cashmere guard hair has higher carbon yield, surface area, and total pore volume, showing a superior adsorption performance.

scholarly journals Waste phenolic resin derived activated carbon by microwave-assisted KOH activation and application to dye wastewater treatment

2019 ◽  
Vol 8 (1) ◽  
pp. 408-415 ◽  
Author(s):  
Wenhai Hu ◽  
Song Cheng ◽  
Hongying Xia ◽  
Libo Zhang ◽  
Xin Jiang ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Carbon ◽  
Surface Area ◽  
Adsorption Isotherms ◽  
Phenolic Resin ◽  
Bet Surface Area ◽  
Isotherm Models ◽  
Koh Activation ◽  
Activation Process ◽  
Dye Wastewater

Abstract The waste phenolic resin was utilized as the raw material to prepare activated carbon (AC) used KOH as the activating agent via microwave heating. The phenolic resin was carbonized at 500°C and then performed with a KOH/Char ratio of 4 and microwave power of 700 W for a duration of 15 min. The physic-chemical characteristics of the AC were characterized by N2 adsorption instrument, FTIR, SEM and TEM. The BET surface area and pore volume of AC were found to be 4269 m2/g and 2.396 ml/g, respectively. The activation process to generate such a phenomenally high surface area of the AC has little reported in open literatures and could pave way for preparation adsorbents that are far superior to the currently marketed adsorbents. The methylene blue (MB) was used as the model to assess its suitability to dye wastewater treatment. Towards this, the MB adsorption isotherms were conducted at three different temperatures and tested with different adsorption isotherm models. The adsorption isotherms could be modeled using Langmuir isotherm. While the kinetics could be used the pseudo-second order kinetics to describe. Thermodynamic results demonstrated that the adsorption process was a spontaneous, as well as an endothermic.

Physical and Chemical Activation Effect on Activated Carbon Prepared from Local Pineapple Waste

2014 ◽  
Vol 699 ◽  
pp. 87-92 ◽  
Author(s):  
Abdul Rahim Yacob ◽  
Adlina Azmi ◽  
Mohd Khairul Asyraf Amat Mustajab
Keyword(s):  
Activated Carbon ◽  
Phosphoric Acid ◽  
Surface Area ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Bet Surface Area ◽  
Activation Effect ◽  
Pineapple Waste ◽  
Pineapple Peel ◽  
Physical And Chemical

The characteristics and quality of activated carbons prepared depending on the chemical and physical properties of the starting materials and the activation method used. In this study, activated carbon prepared using pineapple waste. Three parts of pineapple waste which comprises of peel, crown and leaf were studied. For comparison activated carbon were prepared by both physical and chemical activation respectively. Three types of chemicals were used, phosphoric acid (H3PO4), sulphuric acid (H2SO4), and potassium hydroxide (KOH). The preparation includes carbonization at 200°C and activation at the 400°C using muffle furnace. The chemical characterization of the activated carbon was carried out using Thermogravimetric analysis (TGA), Nitrogen gas adsorption analysis and Fourier transform infrared (FTIR). The highest BET surface area was achieved when the pineapple peel soaked in 20% phosphoric acid with a surface area of 1115 m2g-1. FTIR analysis indicates that the reacted pineapple waste successfully converted into activated carbons.

Sign in / Sign up

Export Citation Format

Share Document