Physical and Chemical Activation Effect on Activated Carbon Prepared from Local Pineapple Waste

2014 ◽  
Vol 699 ◽  
pp. 87-92 ◽  
Author(s):  
Abdul Rahim Yacob ◽  
Adlina Azmi ◽  
Mohd Khairul Asyraf Amat Mustajab
Keyword(s):  
Activated Carbon ◽  
Phosphoric Acid ◽  
Surface Area ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Bet Surface Area ◽  
Activation Effect ◽  
Pineapple Waste ◽  
Pineapple Peel ◽  
Physical And Chemical

The characteristics and quality of activated carbons prepared depending on the chemical and physical properties of the starting materials and the activation method used. In this study, activated carbon prepared using pineapple waste. Three parts of pineapple waste which comprises of peel, crown and leaf were studied. For comparison activated carbon were prepared by both physical and chemical activation respectively. Three types of chemicals were used, phosphoric acid (H3PO4), sulphuric acid (H2SO4), and potassium hydroxide (KOH). The preparation includes carbonization at 200°C and activation at the 400°C using muffle furnace. The chemical characterization of the activated carbon was carried out using Thermogravimetric analysis (TGA), Nitrogen gas adsorption analysis and Fourier transform infrared (FTIR). The highest BET surface area was achieved when the pineapple peel soaked in 20% phosphoric acid with a surface area of 1115 m2g-1. FTIR analysis indicates that the reacted pineapple waste successfully converted into activated carbons.

scholarly journals Characterization of Activated Carbons from Oil-Palm Shell by CO2Activation with No Holding Carbonization Temperature

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
S. G. Herawan ◽  
M. S. Hadi ◽  
Md. R. Ayob ◽  
A. Putra
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Oil Palm ◽  
Pyrolysis Temperature ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Surface Characteristics ◽  
Bet Surface Area ◽  
Preparation Time

Activated carbons can be produced from different precursors, including coals of different ranks, and lignocellulosic materials, by physical or chemical activation processes. The objective of this paper is to characterize oil-palm shells, as a biomass byproduct from palm-oil mills which were converted into activated carbons by nitrogen pyrolysis followed by CO2activation. The effects of no holding peak pyrolysis temperature on the physical characteristics of the activated carbons are studied. The BET surface area of the activated carbon is investigated using N2adsorption at 77 K with selected temperatures of 500, 600, and 700°C. These pyrolysis conditions for preparing the activated carbons are found to yield higher BET surface area at a pyrolysis temperature of 700°C compared to selected commercial activated carbon. The activated carbons thus result in well-developed porosities and predominantly microporosities. By using this activation method, significant improvement can be obtained in the surface characteristics of the activated carbons. Thus this study shows that the preparation time can be shortened while better results of activated carbon can be produced.

Preparation of Activated Carbon of Lignin from Straw Pulping by Chemical Activation Using Potassium Carbonate

2011 ◽  
Vol 704-705 ◽  
pp. 517-522 ◽  
Author(s):  
Xiao Juan Jin ◽  
Zhi Ming Yu ◽  
Gao Jiang Yan ◽  
Wu Yu
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Iodine Number ◽  
Surface Area ◽  
Potassium Carbonate ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Bet Surface Area ◽  
Chemical Agent ◽  
Optimum Conditions

Activated carbons were prepared through chemical activation of lignin from straw pulping precursor using potassium carbonate as the chemical agent. Effects of activated temperature, K2CO3/lignin ratio and the activated time on the yield, Iodine number of activated carbon were investigated. Experimental results indicated that the optimum conditions were as follow: activated temperature 800°C, K3CO3(40% concentration) /lignin ratio 5: l, activated time 50min. These conditions allowed us to obtain a BET surface area of 1104 m2/g, including the external or non-microporous surface of 417 m2/g，Amount of methylene blue adsorption, Iodine number and the yield of activated carbon prepared under optimum conditions were 10.6mL/0.lg,1310 mg/g and 19.75%, respectively.

Preparation of Capacitor’s Electrode from Coconut Shell

2014 ◽  
Vol 875-877 ◽  
pp. 1585-1589
Author(s):  
Arenst Andreas Arie ◽  
Joong Kee Lee
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Electrode Materials ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Coconut Shell ◽  
Bet Surface Area ◽  
Type I ◽  
Activation Temperature ◽  
Bet Analysis

Activated carbons were prepared from coconut shell by chemical activation method and utilized as electrode materials for electrochemical double layer capacitor (EDLC). A preliminary characteristic of activated carbon from coconut shell includes the Brunnaeur Emmett Teller (BET) analysis and cyclic voltammetry measurements. The BET surface area is not affected by the variation of activation temperature as both of the samples showed BET surface area of about 850-870 m2g-1. The N2 adsorption–desorption isotherms showed that the sample exhibited type I characteristics according to IUPAC classification, which confirms its micro-porosity. Compared with the un-activated carbon samples, the activated ones exhibited the better electrochemical properties with a specific capacitance of 150 F g−1 at a scan rate of 2 mV s−1. The good performance of activated carbon is attributed to the enhancement of surface area due to the KOH pretreatment which can open new pores accessible for the ionic transport

scholarly journals Preparation and Characterization of Activated Carbon from Poplar Sawdust by Chemical Activation: Comparison of Different Activating Agents and Carbonization Temperature

2018 ◽  
Vol 3 (11) ◽  
pp. 6-11 ◽  
Author(s):  
Funda Ateş ◽  
Öznur Özcan
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Experimental Studies ◽  
Carbonization Temperature ◽  
Bet Surface Area ◽  
Koh Activation ◽  
Chemical Agent ◽  
Poplar Sawdust

Activated carbons were prepared from poplar sawdust by chemical activation using ZnCl2, H3PO4 or KOH. The influence of activating agents, carbonization temperatures ranging from 500 ºC to 800 ºC, and mass ratio of chemical agent to precursor (1:1 and 2:1) on the porosity of activated carbons were studied. The properties of the carbons were characterized by adsorption/desorption of nitrogen to determine the BET areas, scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FT-IR). It was determined that the surface morphology and textural characteristics of activated carbons vary depending on the carbonization temperature or chemical agent. Maximum surface areas were obtained at carbonization temperatures of 500, 700 and 800 ºC for H3PO4, KOH and ZnCl2 activation, respectively. The activated carbons prepared using ZnCl2 and H3PO4 activation had a higher BET surface area (nearly 1100 m2/g) than that of the KOH activation (761 m2/g). This study also presents a comparison of mechanisms of activating agents and carbonization temperature. As a result of the experimental studies, positive results were obtained, and the production of activated carbon with a high surface area was conducted. 

scholarly journals Effect of textural and chemical characteristics of activated carbons on phenol adsorption in aqueous solutions

2017 ◽  
Vol 19 (4) ◽  
pp. 87-93 ◽  
Author(s):  
Diana P. Vargas ◽  
Liliana Giraldo ◽  
Juan Carlos Moreno-Piraján
Keyword(s):  
Activated Carbon ◽  
Aqueous Solutions ◽  
Surface Area ◽  
Pore Volume ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Chemical Properties ◽  
Granular Activated Carbon ◽  
Bet Surface Area ◽  
Phenol Adsorption

Abstract The effect of textural and chemical properties such as: surface area, pore volume and chemical groups content of the granular activated carbon and monoliths on phenol adsorption in aqueous solutions was studied. Granular activated carbon and monolith samples were produced by chemical activation. They were characterized by using N2 adsorption at 77 K, CO2 adsorption at 273 K, Boehm Titrations and immersion calorimetry in phenol solutions. Microporous materials with different pore size distribution, surface area between 516 and 1685 m2 g−1 and pore volumes between 0.24 and 0.58 cm3 g−1 were obtained. Phenol adsorption capacity of the activated carbon materials increased with increasing BET surface area and pore volume, and is favored by their surface functional groups that act as electron donors. Phenol adsorption capacities are in ranged between 73.5 and 389.4 mg · g−1.

scholarly journals Comparative study for adsorption of acidic and basic dyes on activated carbon prepared from date stone by different activation agent

2020 ◽  
Vol 13 (1) ◽  
pp. 12-20
Author(s):  
Azhaar Radhi Jabbar
Keyword(s):  
Activated Carbon ◽  
Phosphoric Acid ◽  
Surface Area ◽  
Zinc Chloride ◽  
Potassium Hydroxide ◽  
Adsorption Process ◽  
Activated Carbons ◽  
Second Order ◽  
Bet Surface Area ◽  
Pseudo Second Order

This research includes a lab scale work to investigate the feasibility of treating waste water which polluted with dyes exhausted from textile factory by using adsorption process. Three type of activated carbon were prepared using locally available waste material (date stone). Chemical activation method  with (zinc chloride, potassium hydroxide, or phosphoric acid) was used  as activators  to  prepared carbon. Firstly, the materials were carbonized at 275 oC for 90 min and then the carbonized materials were treated with (4 molar) solution of acid, base or salt for 24 hour. Finally, these materials were activated at 600 oC for two hours in the presence of nitrogen gas flow. The resulted activated carbons were checked by its (BET) surface area analysis and surface morphology by SEM. The surface area values were (815, 950,600) m2/g for carbon produced from the activation of date  stone by phosphoric acid, potassium hydroxide or zinc chloride respectively. SEM characterizations show that activated carbons that prepared from potassium hydroxide have higher surface area and good adsorption characteristics than that prepared from activation with phosphoric acid or zinc chloride. The  adsorption process was studied using two types of dyes. The first one is acidic (methyl orange) and the other is basic (bismark brown). The adsorption isotherms and kinetics where investigated for both dyes at temperatures (30,40,50,60)oC for concentration  range  equal to (6-16)mg/l.  The  adsorption data of equilibrium were presented by using two common adsorption isotherm equations. The data was fitted fairly well with Langmuir isotherm for both dyes on all types of prepared activated carbons. The kinetic of adsorption was study by using two kinetic equations, pseudo first order and pseudo second order. The result showed the rapid increase in the rate of adsorption at the initial until equilibrium achieved. Pseudo second order model were represent the data very well with confidence level 0.99.

scholarly journals Chemical Activation of a South African Coal using Phosphoric Acid

1993 ◽  
Vol 10 (1-4) ◽  
pp. 181-192 ◽  
Author(s):  
François D. Botha ◽  
Brian Mcenaney
Keyword(s):  
Activated Carbon ◽  
Phosphoric Acid ◽  
Surface Area ◽  
South African ◽  
Froth Flotation ◽  
Mercury Porosimetry ◽  
Chemical Activation ◽  
Ash Content ◽  
Bet Surface Area ◽  
Adsorption Of Nitrogen

The potential of a South African coal, Bosjesspruit, as a precursor for a phosphoric acid-activated carbon has been assessed using the adsorption of nitrogen at 77 K and mercury porosimetry. Column cleaning of the coal by froth flotation reduced the ash content from 22 to 12 wt.% and caused maceral separtion, resulting in an intertinite-rich product. Reaction of the column-cleaned coal with phosphoric acid in the range 450–550°C produced an activated carbon which was dominantly microporous. The notional BET surface area of the coal reached a maximum of 600 m2/g at a reaction temperature of 550°C.

scholarly journals Pinecone-Derived Activated Carbons as an Effective Medium for Hydrogen Storage

Energies ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2237
Author(s):  
Sara Stelitano ◽  
Giuseppe Conte ◽  
Alfonso Policicchio ◽  
Alfredo Aloise ◽  
Giovanni Desiderio ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Hydrogen Storage ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Hydrogen Adsorption ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Textural Properties ◽  
Biomass Waste ◽  
Wavelength Dispersive Spectrometry

Pinecones, a common biomass waste, has an interesting composition in terms of cellulose and lignine content that makes them excellent precursors in various activated carbon production processes. The synthesized, nanostructured, activated carbon materials show textural properties, a high specific surface area, and a large volume of micropores, which are all features that make them suitable for various applications ranging from the purification of water to energy storage. Amongst them, a very interesting application is hydrogen storage. For this purpose, activated carbon from pinecones were prepared using chemical activation with different KOH/precursor ratios, and their hydrogen adsorption capacity was evaluated at liquid nitrogen temperatures (77 K) at pressures of up to 80 bar using a Sievert’s type volumetric apparatus. Regarding the comprehensive characterization of the samples’ textural properties, the measurement of the surface area was carried out using the Brunauer–Emmett–Teller method, the chemical composition was investigated using wavelength-dispersive spectrometry, and the topography and long-range order was estimated using scanning electron microscopy and X-ray diffraction, respectively. The hydrogen adsorption properties of the activated carbon samples were measured and then fitted using the Langmuir/ Töth isotherm model to estimate the adsorption capacity at higher pressures. The results showed that chemical activation induced the formation of an optimal pore size distribution for hydrogen adsorption centered at about 0.5 nm and the proportion of micropore volume was higher than 50%, which resulted in an adsorption capacity of 5.5 wt% at 77 K and 80 bar; this was an increase of as much as 150% relative to the one predicted by the Chahine rule.

scholarly journals Phenol adsorption on high microporous activated carbons prepared from oily sludge: equilibrium, kinetic and thermodynamic studies

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
N. Mojoudi ◽  
N. Mirghaffari ◽  
M. Soleimani ◽  
H. Shariatmadari ◽  
C. Belver ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Pore Volume ◽  
Activated Carbons ◽  
Ph Value ◽  
Chemical Activation ◽  
Bet Surface Area ◽  
Polluted Water ◽  
Oily Sludge ◽  
Maximum Adsorption Capacity ◽  
Adsorption Desorption

AbstractThe purpose of this study was the preparation, characterization and application of high-performance activated carbons (ACs) derived from oily sludge through chemical activation by KOH. The produced ACs were characterized using iodine number, N2 adsorption-desorption, Fourier-transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The activated carbon prepared under optimum conditions showed a predominantly microporous structure with a BET surface area of 2263 m2 g−1, a total pore volume of 1.37 cm3 g−1 and a micro pore volume of 1.004 cm3 g−1. The kinetics and equilibrium adsorption data of phenol fitted well to the pseudo second order model (R2 = 0.99) and Freundlich isotherm (R2 = 0.99), respectively. The maximum adsorption capacity based on the Langmuir model (434 mg g−1) with a relatively fast adsorption rate (equilibrium time of 30 min) was achieved under an optimum pH value of 6.0. Thermodynamic parameters were negative and showed that adsorption of phenol onto the activated carbon was feasible, spontaneous and exothermic. Desorption of phenol from the adsorbent using 0.1 M NaOH was about 87.8% in the first adsorption/desorption cycle and did not decrease significantly after three cycles. Overall, the synthesized activated carbon from oily sludge could be a promising adsorbent for the removal of phenol from polluted water.

AKTIVASI KIMIA-FISIK LIMBAH SERUTAN ROTAN MENJADI KARBON AKTIF

2014 ◽  
Vol 14 (1) ◽  
pp. 82-98
Author(s):  
Andy Mizwar
Keyword(s):  
Activated Carbon ◽  
Water Content ◽  
Iodine Number ◽  
Surface Area ◽  
Chemical Activation ◽  
Raw Material ◽  
Physical Activation ◽  
Fixed Carbon ◽  
Impregnation Time ◽  
Physical And Chemical

Limbah rotan dari industri kerajinan dan mebel berpotensi untuk dijadikan sebagai bahan baku pembuatan karbon aktif karena memiliki kandungan holoselulosa dan kadar karbon yang tinggi. Penelitian ini bertujuan untuk menganalisis efektifitas dari aktivasi kimia menggunakan larutan natrium klorida (NaCl) yang dilanjutkan dengan aktivasi fisik dalam pembuatan karbon aktif berbahan dasar  limbah serutan rotan. Pembuatan karbon aktif diawali dengan proses karbonisasi pada suhu 250°C selama 1 jam. Selanjutnya aktivasi kimia menggunakan larutan NaCl dengan variasi konsentrasi 10%, 15% dan 20% serta waktu perendaman selama 10, 15 dan 20 jam. Aktivasi fisik dilakukan dengan pembakaran pada suhu 700°C selama 30 menit. Analisis karakteristik fisik-kimia karbon aktif mengacu pada SNI 06-3730-95, meliputi kadar air, fixed carbon, dan iodine number, sedangkan perhitungan luas permukaan spesifik karbon aktif dilakukan dengan Metode Sears. Hasil penelitian ini menunjukkan bahwa kondisi optimum aktivasi kimia terjadi pada konsentrasi NaCl 10% dan lama perendaman 10 jam dengan hasil analisis kadar air 2.90%, fixed carbon 72.70%, iodine number 994.59 mg/g dan luas permukaan 1587.67 m²/g. Peningkatan fixed carbon, iodine number dan luas permukaan karbon aktif berbanding terbalik dengan peningkatan konsentrasi NaCl dan lama waktu perendaman, sedangkan peningkatan kadar air pada karbon aktif berlaku sebaliknya. Rattan waste from handicraft and furniture industry could potentially be used as raw material of activated carbon due to high content of holoselulosa and carbon. This paper investigates the effectiveness of chemical activation using sodium chloride (NaCl) followed by physical activation in the making of activated carbon-based on rattan shavings waste. Preparation of the activated carbon began with the carbonization process at 250°C for 1 hour. Furthermore chemical activation using a variation of NaCl concentrations 10%, 15% and 20% as well as the time of immersion 10, 15 and 20 hours. Physical activation was done by burning at 700°C for 30 minutes. Analysis of the physical and chemical characteristics of the activated carbon was referred to the SNI 06-3730-95, including of moisture content, fixed carbon and iodine number, while the calculation of the specific surface area was done by the Sears’s method. The results of this study showed that the optimum conditions of chemical activation occurred in impregnation by NaCl 10% for 10 hours. The water content, fixed carbon, iodine number and surface area of activated carbon was 2.90%, 72.70%, 994.59 mg/g and 1587.67 m²/g  respectively. The increase values of fixed carbon, iodine number, and surface area was inversely proportional to the increase of NaCl concentration and the length of impregnation time, while the increase of water content applied vice versa.

Sign in / Sign up

Export Citation Format

Share Document