scholarly journals Marine Pollution Mitigation by Waste Oils Recycling Onboard Ships: Technical Feasibility and Need for New Policy and Regulations

2020 ◽  
Vol 7 ◽  
Author(s):  
Michela Mazzoccoli ◽  
Marco Altosole ◽  
Veronica Vigna ◽  
Barbara Bosio ◽  
Elisabetta Arato
Keyword(s):  
Marine Pollution ◽  
Cost Savings ◽  
Waste Recycling ◽  
Fuel Oil ◽  
Waste Oil ◽  
Marine Fuel ◽  
Waste Oils ◽  
Simulation Results ◽  
Oily Waste ◽  
To Receive

About 80% of the total pollution from ships is caused by operational oil discharges into the sea, often made deliberately and in violation of international rules; the main reasons can be due to cost savings or lack of adequate facilities in ports to receive waste oils. Therefore, reducing waste oil discharges is crucial for a proper protection of the marine environment. In this regard, the paper presents the preliminary feasibility of a particular waste recycling technology, aimed at obtaining marine fuel oil from sludge, through a pyrolysis process to be carried out in a small reactor onboard. The originality of the research consists in the adaptation of pyrolysis to oily waste produced by ships, since this technology is traditionally applied to solid waste and biomass. Furthermore, the plant has to be designed for operation on board the ship, therefore under very different constraints compared to traditional land plants. Although the preliminary lab tests and simulation results in the chemical process are promising enough, there are still some technical criticalities due to the energy optimization of the reactor for an efficient use onboard of the whole system. In addition, the possibility of recycling waste, directly onboard ships, is not yet covered by mandatory regulations, which is why shipowners generally still feel unmotivated to invest in such technologies.

Study on Producing Marine Fuel Oil by Blending

2005 ◽  
Vol 23 (3-4) ◽  
pp. 235-241
Author(s):  
Feng Yan*
Keyword(s):  
Fuel Oil ◽  
Marine Fuel

Seawater Scrubbing for the Removal of Sulfur Dioxide in a Steam Turbine Power Plant

2005 ◽  
Author(s):  
Akili D. Khawaji ◽  
Jong-Mihn Wie
Keyword(s):  
Power Plant ◽  
Sulfur Dioxide ◽  
Steam Turbine ◽  
Flue Gas ◽  
Operating Cost ◽  
Cooling Water ◽  
Cost Savings ◽  
Fuel Oil ◽  
So2 Emissions ◽  
Heavy Fuel Oil

The most popular method of controlling sulfur dioxide (SO2) emissions in a steam turbine power plant is a flue gas desulfurization (FGD) process that uses lime/limestone scrubbing. Another relatively newer FGD technology is to use seawater as a scrubbing medium to absorb SO2 by utilizing the alkalinity present in seawater. This seawater scrubbing FGD process is viable and attractive when a sufficient quantity of seawater is available as a spent cooling water within reasonable proximity to the FGD scrubber. In this process the SO2 gas in the flue gas is absorbed by seawater in an absorber and subsequently oxidized to sulfate by additional seawater. The benefits of the seawater FGD process over the lime/limestone process and other processes are; 1) The process does not require reagents for scrubbing as only seawater and air are needed, thereby reducing the plant operating cost significantly, and 2) No solid waste and sludge are generated, eliminating waste disposal, resulting in substantial cost savings and increasing plant operating reliability. This paper reviews the thermodynamic aspects of the SO2 and seawater system, basic process principles and chemistry, major unit operations consisting of absorption, oxidation and neutralization, plant operation and performance, cost estimates for a typical seawater FGD plant, and pertinent environmental issues and impacts. In addition, the paper presents the major design features of a seawater FGD scrubber for the 130 MW oil fired steam turbine power plant that is under construction in Madinat Yanbu Al-Sinaiyah, Saudi Arabia. The scrubber with the power plant designed for burning heavy fuel oil containing 4% sulfur by weight, is designed to reduce the SO2 level in flue gas to 425 ng/J from 1,957 ng/J.

2015 North American ECA: Lessons Learned in CA

2014 ◽  
Author(s):  
Jeff Cowan
Keyword(s):  
Cost Savings ◽  
Lessons Learned ◽  
Fuel Oil ◽  
Compression Ignition ◽  
Heavy Fuel Oil ◽  
Flow Through ◽  
Filter Clogging ◽  
The Cost ◽  
Normal Ambient ◽  
Distillate Fuel

California experienced a 300% increase in loss of propulsion (LOP) incidents since its distillate fuel regulation came into effect in 2009. The compression ignition (Diesel) engines aboard modern cargo ships over 10,000 gross tons use 3.0% sulfur Heavy Fuel Oil (HFO). This fuel must be heated to flow through the fuel lines because at normal ambient temperature HFO has the consistency of tar. Distillate fuel in contrast does not require the high temperatures, and the thermodynamics of cooling metal, gaskets and seals resulted in leaks, along with filter clogging from engine buildup scrubbing. In addition, the cost savings of using HFO are significant over the use of distillate fuel which is typically around US$300 more per ton.

A 12-pulse rectifier with passive harmonic reduction based on UIPT in more electric aircrafts

Circuit World ◽  
2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Rohollah Abdollahi
Keyword(s):  
Power Factor ◽  
Harmonic Distortion ◽  
Cost Savings ◽  
Cost Effective ◽  
Industrial Applications ◽  
Input Current ◽  
New Combination ◽  
Content Type ◽  
Harmonic Reduction ◽  
Simulation Results

Purpose The purpose of this paper is to provide a T autotransformer based 12-pulse rectifier with passive harmonic reduction in more electric aircraft applications. The T autotransformer uses only two main windings which result in volume, space, size, weight and cost savings. Also, the proposed unconventional inter-phase transformer (UIPT) with a lower kVA rating (about 2.6% of the load power) compared to the conventional inter-phase transformer results in a more harmonic reduction. Design/methodology/approach To increase rating and reduce the cost and complexity of a multi-pulse rectifier, it is well known that the pulse number must be increased. In some practical cases, a 12-pulse rectifier (12PR) is suggested as a good solution considering its simple structure and low weight. But the 12PR cannot technically meet the standards of harmonic distortion requirements for some industrial applications, and therefore, they must be used with output filters. In this paper, a 12PR is suggested, which consists of a T autotransformer 12PR and a passive harmonic reduction (PHR) based on the UIPT at direct current (DC) link. Findings To show the advantage of this new combination over other solutions, simulation results are used, and then, a prototype is implemented to evaluate and verify the simulation results. The simulation and experimental test results show that the input current total harmonic distortion (THD) of the suggested 12PR with a PHR based on UIPT is less than 5%, which meets the IEEE 519 requirements. Also, it is shown that in comparison with other solutions, it is cost effective, and at the same time, its power factor is near unity, and its rating is 29.92% of the load rating. Therefore, it is obvious that the proposed rectifier is a practical solution for more electric aircrafts. Originality/value The contributions of this paper are summarized as follows. The suggested design uses a retrofit T autotransformer, which meets all technical constraints, and in comparison, with other options, has less rating, weight, volume and cost. In the suggested rectifier, a PHR based on UIPT at its dc link of 12PR is used, which has good technical capabilities and lower ratings. In the PHR based on UIPT, an IPT is used, which has an additional secondary winding and four diodes. This solution leads to a reduction in input current THD and conduction losses of diodes. In full load conditions, the input line current THD and power factor are 4% and 0.99, respectively. The THD is less than 5%, which satisfies IEEE-519 and DO-160G requirements.

scholarly journals Experimental Investigation of the Use of Waste Mineral Oils as a Fuel with Organic-based Mn Additive

2018 ◽  
Author(s):  
Bulent Özdalyan ◽  
Recep Ç. Orman
Keyword(s):  
Experimental Study ◽  
Diesel Fuel ◽  
Mineral Oil ◽  
Fuel Oil ◽  
Emission Characteristics ◽  
Waste Oil ◽  
Engine Oils ◽  
Mineral Oils ◽  
Heat Value ◽  
Different Doses

The heat values of waste mineral oils are equal to the heat value of the fuel oil. However, heat value alone is not sufficient for the use of waste mineral oils. as fuel. However, the critical physical properties of fuels such as density and viscosity need to be adapted to the system in order to be used. In this study, the engine oils used in the first 10,000 km of the vehicles were used as waste mineral oil. An organic-based Mn additive was synthesized to improve the properties of the waste mineral oil. It was observed that mixing the Mn additive with the waste mineral oil at different doses (4, 8, 12 and 16 ppm) improves the viscosity of the waste oil and the flash point. The resulting fuel was evaluated for emission using different loads in a 5 kW capacity generator to compare the fuel with standard diesel fuel and to determine the effect of Mn addition. In the experimental study, it was observed that the emission characteristics of the fuel obtained from waste mineral oil were worse than diesel fuel, but some improvement with Mn addition. As a result, we found that the use of waste mineral oils in engines in fuel standards was not appropriate, but may be improved with additives.

scholarly journals MASSIVE USE OF BERM RELOCATION AND SURFWASHING DURING THE 2006 JYEH OIL SPILL (LEBANON): THE ACCURATE RESPONSE FOR BEACHES CLEANUP

2008 ◽  
Vol 2008 (1) ◽  
pp. 331-338 ◽  
Author(s):  
Bernard Fichaut ◽  
Bahr Loubnan
Keyword(s):  
Surf Zone ◽  
Weather Conditions ◽  
Fuel Oil ◽  
Shallow Waters ◽  
Power Station ◽  
Heavy Fuel Oil ◽  
Sediment Removal ◽  
Calm Weather ◽  
Oily Waste

ABSTRACT Following the bombardment of the Jyeh power station in Lebanon on July 16 2006, about 10 to 15000 tons of heavy fuel oil drifted 150 km northward all the way to the Syrian border. Because of the continuing war, the cleanup operations could not start until early September. The response consisted of conceptually dividing the coast line into several sectors managed by various operators; from Jyeh to Beyrouth, a 34.5 km stretch of shoreline, the treatment of beaches was assigned to the lebanese N.G.O “Bahr Loubnan’. In this area, 5.3 km of sandy and gravel beaches appeared to be heavily oiled on a width that seldomly exceeded 10 m. Oil was found buried down to a depth of 1.8 m at several locations. Additionnally oil was also found sunken in shallow waters in the breaker zones of numerous beaches. In order to minimize sediment removal and production of oily waste to be treated, it was decided to operate massive treatmenN in situ. After manual recovery of stranded oil, about 12,000 m of sediment including 1,000 m of cobbles have been relocated in the surf zone. Despite the lack of tides and of the generally calm weather conditions, surfwashing was very efficient due mainly to the fact that, in non tidal conditions, sediments are continuously reworked by wave açtion which operates at the same level on the beaches. Only 540 m of heavily oiled sand, was removed from beaches and submitted for further treatment. The lack of appropriate sorbents material in Lebanon to capture the floating oil released by surfwahing was also a challenge. This was addressed by using locally Nmanufactured sorbents, which proved to be very efficient and 60 m of sorbent soaked with oil were produced during the cleanup.

scholarly journals An Improved Mobility Aware Relaying Scheme for Body Area Networks

2020 ◽  
Author(s):  
Costas Michaelides ◽  
Maria Iloridou ◽  
Foteini-Niovi Pavlidou
Keyword(s):  
Random Access ◽  
High Mobility ◽  
Body Area Networks ◽  
Ieee 802.15.6 ◽  
Body Area ◽  
Star Topology ◽  
Packet Delivery ◽  
Safety Regulations ◽  
Simulation Results ◽  
To Receive

Communication in Body Area Networks (BANs) involves weak signals, due to safety regulations, huge pathloss from the absorption and usually high mobility. In this work, we introduce an improved mobility aware relaying scheme for BANs, as an alternative to the two-hop star topology extension of IEEE 802.15.6-2012, in order to enhance packet delivery. Specifically, an emergency phase (EP) is added after the regular random access phase (RAP1) of the superframe and the connected nodes transmit rescue beacons to reach disconnected nodes. When a disconnected node receives a rescue beacon, it participates in the current EP. The packets are buffered and relayed to the hub by the connected nodes. Simulation results show that it is feasible to receive more packets compared to the standard with a justified increase of energy consumption due to random access which is compensated with increased packet delivery.

Using natural crystalline zeolite structure in order to reduce the acidity in marine fuel oil

2016 ◽  
Vol 34 (23) ◽  
pp. 1899-1904
Author(s):  
Constantinos Tsanaktsidis ◽  
Adams Z. Stimoniaris ◽  
Konstantinos Spinthiropoulos ◽  
George Tzilantonis ◽  
Ilias N. Smaragdis
Keyword(s):  
Fuel Oil ◽  
Marine Fuel ◽  
Zeolite Structure
Sign in / Sign up

Export Citation Format

Share Document