scholarly journals Interferometry of Gas-Phase Flows during Selective Laser Melting

2019 ◽  
Vol 10 (1) ◽  
pp. 231 ◽  
Author(s):  
Pavel A. Podrabinnik ◽  
Alexander E. Shtanko ◽  
Roman S. Khmyrov ◽  
Andrey D. Korotkov ◽  
Andrey V. Gusarov
Keyword(s):  
Gas Phase ◽  
Selective Laser Melting ◽  
Laser Power ◽  
Metal Vapor ◽  
Gas Jet ◽  
Laser Melting ◽  
Pressure Fields ◽  
Ambient Gas ◽  
Processing Zone

Gas-phase flows occurring in a plume in a processing zone during selective laser melting (SLM) can significantly affect the quality of the process. To further enhance SLM performance, the characteristics of the flows should be considered. In this article, the vapor-gas jet emerging from the laser processing zone was studied. It was visualized by interferometry to evaluate flow velocity, geometry and changes in refractory index depending on laser power. The velocity and pressure fields of the vapor jet and the entrained ambient gas were estimated by mathematical modeling. It was shown that the increase of laser power led to higher jet velocity and greater change in its refractory index. The latter also was used to evaluate the content of metal vapor in the plume and its influence on the absorption of laser radiation.

Effects of the Processing Parameters on the Forming Quality of Stainless Steel Parts by Selective Laser Melting

2011 ◽  
Vol 189-193 ◽  
pp. 3668-3671 ◽  
Author(s):  
Qing Song Wei ◽  
Xiao Zhao ◽  
Li Wang ◽  
Rui Di Li ◽  
Jie Liu ◽  
...  
Keyword(s):  
Layer Thickness ◽  
Selective Laser Melting ◽  
Molten Pool ◽  
Laser Power ◽  
Single Layer ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Powder Layer ◽  
Laser Melting

Selective Laser Melting (SLM) can produce high-performance metal parts with complex structures. However, it’s difficult to control the processing parameters, because many factors involves. From the perspective of the molten pool, the study focuses on the effects of processing parameters, including scanning speed, laser power, scanning space, layer thickness, and scanning strategies, on the surface quality, the balling effect, the density of SLM parts, by conducting experiments of single track, single layer and block forming. The results show that the quality of the molten pool is affected by laser power and scanning speed. Scanning drove in the strategy of “jumping and turning”，a smooth surface and a less balling effect will be obtained. The thicker the powder layer is, the lower density will be obtained. The optimal parameters from series of experiments are: laser power of 98W; scanning speed of 90mm/s; scanning space of 0.07mm; layer thickness of 0.1mm; and scanning strategy of “jumping and turning”.

scholarly journals Investigation of Laser Polishing of Four Selective Laser Melting Alloy Samples

2020 ◽  
Vol 10 (3) ◽  
pp. 760
Author(s):  
Dongqi Zhang ◽  
Jie Yu ◽  
Hui Li ◽  
Xin Zhou ◽  
Changhui Song ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Selective Laser Melting ◽  
Laser Power ◽  
Layer By Layer ◽  
Metal Powders ◽  
Laser Melting ◽  
Laser Polishing

Selective laser melting (SLM) is a layer by layer process of melting and solidifying of metal powders. The surface quality of the previous layer directly affects the uniformity of the next layer. If the surface roughness value of the previous layer is large, there is the possibility of not being able to complete the layering process such that the entire process has to be abandoned. At least, it may result in long term durability problem and the inhomogeneity, may even make the processed structure not be able to be predicted. In the present study, the ability of a fiber laser to in-situ polish the rough surfaces of four typical additive-manufactured alloys, namely, Ti6Al4V, AlSi10Mg, 316L and IN718 was demonstrated. The results revealed that the surface roughness of the as-received alloys could be reduced to about 3 μm through the application of the laser-polishing process, and the initial surfaces had roughness values of 8.80–16.64 μm. Meanwhile, for a given energy density, a higher laser power produced a laser-polishing effect that was often more obvious, with the surface roughness decreasing with an increase in the laser power. Further, the polishing strategy will be optimized by simulation in our following study.

scholarly journals Determinants of the surface quality, density and dimensional correctness in selective laser melting of the Ti-13Zr-13Nb alloy

2018 ◽  
Vol 106 (4) ◽  
pp. 405
Author(s):  
Tomasz Seramak ◽  
Katarzyna Zasinska ◽  
Michel Mesnard ◽  
Karolina Bednarz ◽  
Paulina Fic ◽  
...  
Keyword(s):  
Energy Density ◽  
Relative Density ◽  
Surface Quality ◽  
Selective Laser Melting ◽  
Laser Power ◽  
Thermal Stresses ◽  
Laser Melting ◽  
Dimensional Precision ◽  
Scan Time

Selective laser melting is widely used for custom-designed elements. Successful manufacturing depends on laser treatment parameters and material features. This research aimed to determine the effects of laser power, scan time and hatch distance on surface quality, relative density and dimensional precision for cuboids made of the Ti-13Zr-13Nb alloy. The influence of energy density, energy flux and pre-heating was seen to be decisive to different degrees for the quality of the final specimen. The results obtained were used to produce prosthetic crowns and bridges. The thermal stresses that appeared resulted in a deflection of the bridges and consequently in a change in design approach.

scholarly journals Experiment of Process Strategy of Selective Laser Melting Forming Metal Nonhorizontal Overhanging Structure

Metals ◽  
2019 ◽  
Vol 9 (4) ◽  
pp. 385 ◽  
Author(s):  
Wentian Shi ◽  
Peng Wang ◽  
Yude Liu ◽  
Guoliang Han
Keyword(s):  
Surface Roughness ◽  
Selective Laser Melting ◽  
Laser Power ◽  
316L Stainless Steel ◽  
Laser Melting ◽  
Scanning Strategy ◽  
Forming Quality ◽  
Forming Angle ◽  
Suspension Structure

To improve the precision of the nonhorizontal suspension structure and the forming quality of the overhanging surface by selective laser melting, the influence of laser power on the upper surface and the overhanging surface forming quality of 316L stainless steel at different forming angles was studied in the experiment. The influence of different scanning strategies, upper surface remelting optimization, and overhang boundary scanning optimization on the formation of overhanging structures was compared and analyzed. The forming effect of chromium–nickel alloy is better than 316L stainless steel below the limit forming angle in the overhanging structure. The better forming effect of chromium–nickel alloy can be obtained by narrowing the hatch space with the boundary optimization process. The experiment results show that the forming of the overhanging structure below the limit forming angle should adopt the chessboard scanning strategy. The smaller laser power remelting is beneficial to both the forming of the overhanging surface and the quality of upper surface forming. The minimum value of surface roughness using the 110 W power laser twice during surface remelting and boundary scanning 75° overhanging surface can reach 11.9 μm and 31.1μm, respectively. The forming accuracy error range above the limit forming angle is controlled within 0.4 mm, and the forming quality is better. A boundary count scanning strategy was applied to this study to obtain lower overhanging surface roughness values. This research proposes a process optimization and improvement method for the nonhorizontal suspension structure formed by selective laser melting, which provides the process support for practical application.

scholarly journals Effect of Process Parameters and Layer Thickness on the Quality and Performance of Ti-6Al-4V Fabricated by Selective Laser Melting

Coatings ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1323
Author(s):  
Yanlong Jing ◽  
Peng Wang ◽  
Xiaoling Yan
Keyword(s):  
Surface Quality ◽  
Selective Laser Melting ◽  
Exposure Time ◽  
Process Parameters ◽  
Laser Power ◽  
Single Track ◽  
Laser Melting ◽  
Powder Bed ◽  
Point Distance

To improve the quality of thick powder bed and realize the matching of thick powder bed and thin powder bed in the later stage, the influence of process parameters for the single-track, multi-layer fabrication, relative density, surface quality, defect, remelting, and boundary optimization performance of different layer thicknesses of Ti-6Al-4V fabricated by selective laser melting were investigated. It is more conducive to the stable forming of single-track when the point distance is half the diameter of the laser beam, and the exposure time is appropriately extended. The thin powder bed needs the corresponding point distance and exposure time under the laser power of 280–380 W to obtain high-density specimens. The thick powder bed needs to be able to ensure the formation of high-quality specimens under the smaller point distance and longer exposure time under higher laser power of 380 W. Both thick powder bed and thin powder bed will cause un-melted defects between molten pools, spheroidization defects caused by splashing, and microporous defects. The remelting process can significantly improve the surface quality of the formed specimen, but the surface quality of the thick powder bed is worse than that of the thin powder bed. The boundary quality of thick powder bed is worse than that of thin powder bed, and the boundary shape has a greater influence on the quality of the SLM forming boundary. Different strategies should be adopted to form the boundary of different shapes. Increasing the boundary count and increasing the laser power are more conducive to the improvement of boundary quality.

Effect of laser rescanning on Ti6Al4V microstructure during selective laser melting

2020 ◽  
pp. 095440542097609
Author(s):  
Weipeng Duan ◽  
Meiping Wu ◽  
Jitai Han
Keyword(s):  
Wear Resistance ◽  
Titanium Alloy ◽  
Selective Laser Melting ◽  
Human Body ◽  
High Impact ◽  
Laser Melting ◽  
Heat Treated ◽  
Volume Porosity ◽  
Biomedical Field

TC4, which is one of the most widely used titanium alloy, is frequently used in biomedical field due to its biocompatible. In this work, selective laser melting (SLM) was used to manufacture TC4 parts and the printed parts were heat-treated using laser rescanning technology. The experimental results showed that laser rescanning had a high impact on the quality of SLMed part, and a different performance on wear resistance can be found on the basis. It can be seen that the volume porosity of the sample was 7.6 ± 0.5% without using any further processing technology. The volume porosity of the sample processed using laser rescanning strategy was decreased and the square-framed rescanning strategy had a relative optimal volume porosity (1.5 ± 0.3%) in all these five samples. With the further decreasing of volume porosity, the wear resistance decreased at the same time. As its excellent bio-tribological properties, the square-framed rescanning may be a potential suitable strategy to forming TC4 which used in human body.

Liquation and Crystallization Cracks in Aluminum Alloy AA2024 during Selective Laser Melting

2021 ◽  
Vol 410 ◽  
pp. 203-208
Author(s):  
I.S. Loginova ◽  
N.A. Popov ◽  
A.N. Solonin
Keyword(s):  
Aluminum Alloy ◽  
Selective Laser Melting ◽  
Laser Scanning ◽  
Scanning Speed ◽  
Melting Zone ◽  
Alloying Elements ◽  
Laser Melting ◽  
Laser Scanning Speed ◽  
Positive Effect

In this work we studied the microstructure and microhardness of standard AA2024 alloy and AA2024 alloy with the addition of 1.5% Y after pulsed laser melting (PLM) and selective laser melting (SLM). The SLM process was carried out with a 300 W power and 0.1 m/s laser scanning speed. A dispersed microstructure without the formation of crystallization cracks and low liquation of alloying elements was obtained in Y-modified AA2024 aluminum alloy. Eutectic Al3Y and Al8Cu4Y phases were detected in Y-modified AA2024 aluminum alloy. It is led to a decrease in the formation of crystallization cracks The uniform distribution of alloying elements in the yttrium-modified alloy had a positive effect on the quality of the laser melting zone (LMZ) and microhardness.

scholarly journals Thermo-Fluid-Dynamic Modeling of the Melt Pool during Selective Laser Melting for AZ91D Magnesium Alloy

Materials ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4157
Author(s):  
Hongyao Shen ◽  
Jinwen Yan ◽  
Xiaomiao Niu
Keyword(s):  
Temperature Distribution ◽  
Magnesium Alloy ◽  
Selective Laser Melting ◽  
Laser Power ◽  
Large Temperature ◽  
Fe Model ◽  
Laser Melting ◽  
Az91d Magnesium Alloy ◽  
Melt Pool ◽  
Flow Activity

A three dimensional finite element model (FEM) was established to simulate the temperature distribution, flow activity, and deformation of the melt pool of selective laser melting (SLM) AZ91D magnesium alloy powder. The latent heat in phase transition, Marangoni effect, and the movement of laser beam power with a Gaussian energy distribution were taken into account. The influence of the applied linear laser power on temperature distribution, flow field, and the melt-pool dimensions and shape, as well as resultant densification activity, was investigated and is discussed in this paper. Large temperature gradients and high cooling rates were observed during the process. A violent flow occurred in the melt pool, and the divergent flow makes the melt pool wider and longer but shallower. With the increase of laser power, the melt pool’s size increases, but the shape becomes longer and narrower. The width of the melt pool in single-scan experiment is acquired, which is in good agreement with the results predicted by the simulation (with error of 1.49%). This FE model provides an intuitive understanding of the complex physical phenomena that occur during SLM process of AZ91D magnesium alloy. It can help to select the optimal parameters to improve the quality of final parts and reduce the cost of experimental research.

Influence of the Powder Particle Size on the Denudated Zone Width at Selective Laser Melting

2020 ◽  
Vol 989 ◽  
pp. 816-820
Author(s):  
Roman Sergeevich Khmyrov ◽  
R.R. Ableyeva ◽  
Tatiana Vasilievna Tarasova ◽  
A.V. Gusarov
Keyword(s):  
Particle Size ◽  
Selective Laser Melting ◽  
Powder Particle ◽  
Powder Particle Size ◽  
Adhesion Forces ◽  
Laser Melting ◽  
Friction Forces ◽  
Single Bead ◽  
Powder Particles

Mass transfer in the laser-interaction zone at selective laser melting influences the quality of the obtained material. Powder particles displacement during the formation of the single bead is experimentally studied. The so-called denudated zone was visualized by metallography. It was determined that increasing the powder particle size leads to widening the denudated zone. This can signify that the adhesion forces between powder particles prevail over the friction forces.

Sign in / Sign up

Export Citation Format

Share Document