scholarly journals Mechanical and Thermal Stress Behavior of a Conservative Proposed Veneer Preparation Design for Restoring Misaligned Anterior Teeth: A 3D Finite Element Analysis

2020 ◽  
Vol 10 (17) ◽  
pp. 5814
Author(s):  
Shilan Nawzad Dawood ◽  
Abdulsalam Rasheed Al-Zahawi ◽  
Laith Abed Sabri
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Thermal Stress ◽  
Thermal Loading ◽  
Effect Of Temperature ◽  
Maxillary Incisor ◽  
Stress Distributions ◽  
Element Analysis ◽  
Anterior Teeth ◽  
Preparation Design

The objective of this study was to evaluate the biomechanical and thermal behavior of a proposed preparation design as a conservative treatment option that aims to preserve both gingival and tooth health structures through a comparative finite element analysis with non-preparation and conventional designs. 3D solid models of laminate veneers with different preparation designs were obtained using cone-beam computed tomography (CBCT) scanning of the maxillary incisor. A 100-Newton load was applied with angulations of 60° and 125° to the longitudinal axis of the tooth to determine the stresses during mastication. In addition, transient thermal analysis was performed to compare the temperature and thermal distribution of the restored tooth models when subjected to thermal loads of 5 °C and 55 °C. Teeth prepared with the proposed design showed lower stress distributions and a repairable failure mode, followed by the non-preparation design, while teeth prepared with the conventional design showed the highest stress concentrations. Furthermore, cold thermal loading yielded larger thermal stress distributions than hot thermal loading, independent of the preparation type, and the effect of temperature changes were within the critical limit near the pulp and dentin regions. Thus, the preparation design geometry affects the long-term success of laminate restoration, and the proposed design yields more uniform and appropriate stress distributions than the other techniques.

Evaluation of Adhesive T-Joint Using Finite Element Analysis

2015 ◽  
Vol 786 ◽  
pp. 37-42 ◽  
Author(s):  
B. Izzawati ◽  
Mohd Afendi ◽  
S. Nurhashima ◽  
A. Nor ◽  
Abdul Rahman Abdullah ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Adhesive Layer ◽  
Effect Of Temperature ◽  
Fe Model ◽  
Stress Distributions ◽  
Adhesive Properties ◽  
Element Analysis ◽  
Parametric Studies ◽  
And Behavior

This study evaluates the effect of temperature upon adhesive properties and behavior of adhesively bonded T-joint. Finite element analyses established the effect of this parameter on the durability joint and stress distribution within the adhesive layer. A series of temperatures and stress analyses using finite element analysis (FEA) has been conducted in the T-joint configuration for this purpose. The parametric studies on the FE model revealed that stress distributions are sensitive to the changes in adhesive properties due to changes in temperature. In general, stresses were reduced with changes in the temperature which resulted in the ability of the adhesive layer to undergo plastic deformation.

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

scholarly journals Finite Element Analysis of Mandibular Anterior Teeth with Healthy, but Reduced Periodontium

2021 ◽  
Vol 11 (9) ◽  
pp. 3824
Author(s):  
Ioana-Andreea Sioustis ◽  
Mihai Axinte ◽  
Marius Prelipceanu ◽  
Alexandra Martu ◽  
Diana-Cristala Kappenberg-Nitescu ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Periodontal Ligament ◽  
Tooth Movement ◽  
Orthodontic Tooth Movement ◽  
Real Data ◽  
Element Analysis ◽  
Anterior Teeth ◽  
Applied Forces ◽  
Orthodontic Forces

Finite element analysis studies have been of interest in the field of orthodontics and this is due to the ability to study the stress in the bone, periodontal ligament (PDL), teeth and the displacement in the bone by using this method. Our study aimed to present a method that determines the effect of applying orthodontic forces in bodily direction on a healthy and reduced periodontium and to demonstrate the utility of finite element analysis. Using the cone-beam computed tomography (CBCT) of a patient with a healthy and reduced periodontium, we modeled the geometric construction of the contour of the elements necessary for the study. Afterwards, we applied a force of 1 N and a force of 0.8 N in order to achieve bodily movement and to analyze the stress in the bone, in the periodontal ligament and the absolute displacement. The analysis of the applied forces showed that a minimal ligament thickness is correlated with the highest value of the maximum stress in the PDL and a decreased displacement. This confirms the results obtained in previous clinical practice, confirming the validity of the simulation. During orthodontic tooth movement, the morphology of the teeth and of the periodontium should be taken into account. The effect of orthodontic forces on a particular anatomy could be studied using FEA, a method that provides real data. This is necessary for proper treatment planning and its particularization depends on the patient’s particular situation.

scholarly journals Fractographical Analysis and Biomechanical Considerations of a Tooth Restored With Intracanal Fiber Post: Report of the Fracture and Importance of the Fiber Arrangements

2016 ◽  
Vol 41 (5) ◽  
pp. E149-E158 ◽  
Author(s):  
VF Wandscher ◽  
CD Bergoli ◽  
IF Limberger ◽  
TP Cenci ◽  
P Baldissara ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Glass Fiber ◽  
Shear Stresses ◽  
Fiber Post ◽  
Element Analysis ◽  
Parallel Fibers ◽  
Tooth Structure ◽  
Anterior Teeth ◽  
Compressive Stresses

SUMMARY Objective: This article aims to present a fractographic analysis of an anterior tooth restored with a glass fiber post with parallel fiber arrangement, taking into account force vectors, finite element analysis, and scanning electron microscopy (SEM). Methods: A patient presented at the Faculty of Dentistry (Federal University of Santa Maria, Brazil) with an endodontically treated tooth (ETT), a lateral incisor that had a restorable fracture. The treatment was performed, and the fractured piece was analyzed using stereomicroscopy, SEM, and finite element analysis. Results: The absence of remaining coronal tooth structure might have been the main factor for the clinical failure. We observed different stresses actuating in an ETT restored with a fiber post as well as their relationship with the ultimate fracture. Tensile, compression, and shear stresses presented at different levels inside the restored tooth. Tensile and compressive stresses acted together and were at a maximum in the outer portions and a minimum in the inner portions. In contrast, shear stresses acted concomitantly with tensile and compressive stresses. Shear was higher in the inner portions (center of the post), and lower in the outer portions. This was confirmed by finite element analysis. The SEM analysis showed tensile and compression areas in the fiber post (exposed fibers=tensile areas=lingual surface; nonexposed fibers=compression areas=buccal surface) and shear areas inside the post (scallops and hackle lines). Stereomicroscopic analysis showed brown stains in the crown/root interface, indicating the presence of microleakage (tensile area=lingual surface). Conclusion: We concluded that glass fiber posts with parallel fibers (0°), when restoring anterior teeth, present a greater fracture potential by shear stress because parallel fibers are not mechanically resistant to support oblique occlusal loads. Factors such as the presence of remaining coronal tooth structure and occlusal stability assist in the biomechanical equilibrium of stresses that act upon anterior teeth.

Three Turnaround Heat Treating Studies

2003 ◽  
Author(s):  
Jaan Taagepera ◽  
Marty Clift ◽  
D. Mike DeHart ◽  
Keneth Marden
Keyword(s):  
Heat Treatment ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Thermal Stress ◽  
Thermal Stresses ◽  
Heat Treating ◽  
Element Analysis ◽  
Stress Profiles ◽  
Insight Into

Three vessel modifications requiring heat treatment were analyzed prior to and during a planned turnaround at a refinery. One was a thick nozzle that required weld build up. This nozzle had been in hydrogen service and required bake-out to reduce the potential for cracking during the weld build up. Finite element analysis was used to study the thermal stresses involved in the bake-out. Another heat treatment studied was a PWHT of a nozzle replacement. The heat treatment band and temperature were varied with location in order to minimize cost and reduction in remaining strength of the vessel. Again, FEA was used to provide insight into the thermal stress profiles during heat treatment. The fmal heat treatment study was for inserting a new nozzle in a 1-1/4Cr-1/2Mo reactor. While this material would ordinarily require PWHT, the alteration was proposed to be installed without PWHT. Though accepted by the Jurisdiction, this nozzle installation was ultimately cancelled.

Finite Element Analysis of Thermal Stress Distribution in Planar SOFC

2019 ◽  
Vol 7 (1) ◽  
pp. 1977-1986 ◽  
Author(s):  
Chih-Kuang Lin ◽  
Tsung-Ting Chen ◽  
An-Shin Chen ◽  
Yau-Pin Chyou ◽  
Lieh-Kwang Chiang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Thermal Stress ◽  
Stress Distribution ◽  
Element Analysis ◽  
Thermal Stress Distribution

scholarly journals Characteristics and Dynamics of Full Arch Distalization Using Transpalatal Arches with Midpalatal and Interradicular Miniscrews as Temporary Anchorage Devices: A Preliminary Finite Element Analysis

2020 ◽  
Vol 2020 ◽  
pp. 1-19
Author(s):  
Mashallah Khanehmasjedi ◽  
Sepideh Bagheri ◽  
Vahid Rakhshan ◽  
Mojtaba Hasani
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Orthodontic Appliances ◽  
Element Analysis ◽  
Midpalatal Suture ◽  
Second Molar ◽  
Bodily Movement ◽  
Anterior Teeth ◽  
The Right

Introduction. Miniscrews have proved quite effective in fixed orthodontic treatment. They can be placed in areas like palatal interradicular zones or midpalatal suture. Despite the value of these methods and their ever-increasing use, their characteristics are not assessed before when implanted in palatal interradicular areas or in the midpalatal suture. We aimed to assess, for the first time, the dynamics of full arch distalization using such miniscrews. Methods. A 3D model of maxilla with all permanent dentition was created from a CT scan volume. Tissues were segmented and differentiated. Afterward, miniscrews and appliances were designed, and the whole model was registered within a finite element analysis software by assigning proper mechanical properties to tissues and orthodontic appliances. The full arches were distalized using transpalatal arches with miniscrews as anchorage devices (in two different models). The extents of stresses and patterns of movements of various elements (teeth, miniscrews, appliances, tissues) were estimated. Results and Conclusions. Comparing the two models, it is obvious that in both models, the stress distribution is the highest in the TPA arms and the head of the miniscrew where the spring is connected. In comparison with the displacement in the X-axis, the “mesial in” rotation is seen in the first molar of both models. But there is one exception and that is the “mesial out” rotation of the right second molar. In all measurements, the amount of movement in Model 2 (with palatal interradicular miniscrews) is more than that in Model 1 (with midpalatal miniscrew). In the Y-axis, more tipping is seen in Model 2, especially the anterior teeth (detorque) and the first molar, but in Model 1, bodily movement of the first molar is more evident. Along the Z-axis, the mesial intrusion of the first molar and the distal extrusion of this tooth can be seen in both models. Again, the displacement values are higher in the second model (with interradicular miniscrews). In comparison with micromotion and stress distribution of miniscrews, in Model 1, maximum stress and micromotion is observed at the head of the miniscrew where it is attached to the spring. Of course, this amount of micromotion increases over time. The same is true for Model 2, but with a lower micromotion. As for the amount of stress, the stress distribution in both miniscrews of both models is almost uniform and rather severe.

scholarly journals Fatigue resistance and 3D finite element analysis of machine-milled ceramic occlusal veneers with new preparation designs versus conventional design: an in vitro study

F1000Research ◽  
2019 ◽  
Vol 8 ◽  
pp. 1038 ◽  
Author(s):  
Samaa Kotb ◽  
Atef Shaker ◽  
Carl Halim
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Fatigue Resistance ◽  
Element Analysis ◽  
3D Finite Element ◽  
Group Iii ◽  
Conventional Design ◽  
Group I ◽  
Group Ii ◽  
Preparation Design

Background: Treatment of patients with severe tooth wear is complex. Treatments involving more tooth structure removal may be inappropriate for patients who have already lost a significant amount of dental tissue due to erosion. The aim of this study was to evaluate the effect of two modified occlusal veneer preparations on the fatigue resistance and stress distribution of bonded occlusal veneers, in comparison to the conventional preparation design. Methods: A total of 54 human mandibular molars were distributed into three equal groups of n=18 teeth each, according to the occlusal veneer preparation design, where group I (conventional design) received Planar occlusal veneer preparation, group II (occlusal veneer with circumferential finish line) and group III (occlusal veneer with intracoronal cavity extension). For the manufacture of all the veneers using machinable zirconium lithium silicate glass ceramic blocks, a computer aided design/manufacturing system was used. A dual cure, adhesive resin cement was used to bond all occlusal veneers to corresponding prepared teeth. After storage in water for one week, step-stress (accelerated life testing was performed for all samples. Finite element analysis was carried out as well to evaluate the distribution of stresses. Results: The highest values (mean±SD) were recorded for group II (890.57±211.53 N) followed by Group I values (883.54±135.91 N), while the lowest values were recorded for Group III (875.57±143.52 N). The difference between groups was statistically non-significant as indicated by ANOVA (P=0.9814>0.05). The stress values were generally found to be low and their distribution differed among groups. Conclusion: Group I and II showed comparable fatigue resistance and more favourable failure behaviour when compared to Group III based on the fractographic and 3D finite element analyses.

Sign in / Sign up

Export Citation Format

Share Document