scholarly journals Fracturing Fluids and Their Application in the Republic of Croatia

2021 ◽  
Vol 11 (6) ◽  
pp. 2807
Author(s):  
Nediljka Gaurina-Međimurec ◽  
Vladislav Brkić ◽  
Matko Topolovec ◽  
Petar Mijić
Keyword(s):  
Hydraulic Fracturing ◽  
Gas Production ◽  
Well Performance ◽  
Fracturing Fluid ◽  
Wellhead Pressure ◽  
Well Production ◽  
Main Requirement ◽  
Fracturing Fluids ◽  
Fluid Properties ◽  
The Republic

Hydraulic fracturing operations are performed to enhance well performance and to achieve economic success from improved production rates and the ultimate reserve recovery. To achieve these goals, fracturing fluid is pumped into the well at rates and pressures that result in the creation of a hydraulic fracture. Fracturing fluid selection presents the main requirement for the successful performance of hydraulic fracturing. The selected fracturing fluid should create a fracture with sufficient width and length for proppant placement and should carry the proppant from the surface to the created fracture. To accomplish all those demands, additives are added in fluids to adjust their properties. This paper describes the classification of fracturing fluids, additives for the adjustment of fluid properties and the requirements for fluid selection. Furthermore, laboratory tests of fracturing fluid, fracture stimulation design steps are presented in the paper, as well as a few examples of fracturing fluids used in Croatia with case studies and finally, hydraulic fracturing performance and post-frac well production results. The total gas production was increased by 43% and condensate production by 106% in selected wells including wellhead pressure, which allowed for a longer production well life.

scholarly journals Laboratory Testing of Fracture Conductivity Damage by Foam-Based Fracturing Fluids in Low Permeability Tight Gas Formations

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1783
Author(s):  
Klaudia Wilk-Zajdel ◽  
Piotr Kasza ◽  
Mateusz Masłowski
Keyword(s):  
Hydraulic Fracturing ◽  
Guar Gum ◽  
Polymer Concentration ◽  
Laboratory Research ◽  
Damage Effect ◽  
Tight Gas ◽  
Fracturing Fluid ◽  
Fracture Conductivity ◽  
Fracturing Fluids ◽  
Sandstone Rock

In the case of fracturing of the reservoirs using fracturing fluids, the size of damage to the proppant conductivity caused by treatment fluids is significant, which greatly influence the effective execution of hydraulic fracturing operations. The fracturing fluid should be characterized by the minimum damage to the conductivity of a fracture filled with proppant. A laboratory research procedure has been developed to study the damage effect caused by foamed and non-foamed fracturing fluids in the fractures filled with proppant material. The paper discusses the results for high quality foamed guar-based linear gels, which is an innovative aspect of the work compared to the non-foamed frac described in most of the studies and simulations. The tests were performed for the fracturing fluid based on a linear polymer (HPG—hydroxypropyl guar, in liquid and powder form). The rheology of nitrogen foamed-based fracturing fluids (FF) with a quality of 70% was investigated. The quartz sand and ceramic light proppant LCP proppant was placed between two Ohio sandstone rock slabs and subjected to a given compressive stress of 4000–6000 psi, at a temperature of 60 °C for 5 h. A significant reduction in damage to the quartz proppant was observed for the foamed fluid compared to that damaged by the 7.5 L/m3 natural polymer-based non-foamed linear fluid. The damage was 72.3% for the non-foamed fluid and 31.5% for the 70% foamed fluid, which are superior to the guar gum non-foamed fracturing fluid system. For tests based on a polymer concentration of 4.88 g/L, the damage to the fracture conductivity by the non-foamed fluid was 64.8%, and 26.3% for the foamed fluid. These results lead to the conclusion that foamed fluids could damage the fracture filled with proppant much less during hydraulic fracturing treatment. At the same time, when using foamed fluids, the viscosity coefficient increases a few times compared to the use of non-foamed fluids, which is necessary for proppant carrying capacities and properly conducted stimulation treatment. The research results can be beneficial for optimizing the type and performance of fracturing fluid for hydraulic fracturing in tight gas formations.

Simultaneous Hydraulic Fracturing Improves Completion Efficiency and Lowers Costs Per Foot

2021 ◽  
Author(s):  
David Russell ◽  
Price Stark ◽  
Sean Owens ◽  
Awais Navaiz ◽  
Russell Lockman
Keyword(s):  
Hydraulic Fracturing ◽  
Oil And Gas ◽  
Horizontal Wells ◽  
Asset Returns ◽  
Gas Production ◽  
Well Performance ◽  
Additional Time ◽  
Oil And Gas Production ◽  
Single Well ◽  
Lateral Length

Abstract Reducing well costs in unconventional development while maintaining or improving production continues to be important to the success of operators. Generally, the primary drivers for oil and gas production are treatment fluid volume, proppant mass, and the number of stages or intervals along the well. Increasing these variables typically results in increased costs, causing additional time and complexity to complete these larger designs. Simultaneously completing two wells using the same volumes, rates, and number of stages as for any previous single well, allows for more lateral length or volume completed per day. This paper presents the necessary developments and outcomes of a completion technique utilizing a single hydraulic fracturing spread to simultaneously stimulate two or more horizontal wells. The goal of this technique is to increase operational efficiency, lower completion cost, and reduce the time from permitting a well to production of that well—without negatively impacting the primary drivers of well performance. To date this technique has been successfully performed in both the Bakken and Permian basins in more than 200 wells, proving its success can translate to other unconventional fields and operations. Ultimately, over 200 wells were successfully completed simultaneously, resulting in a 45% increase in completion speed and significant decrease in completion costs, while still maintaining equivalent well performance. This type of simultaneous completion scenario continues to be implemented and improved upon to improve asset returns.

Leak-Off Coefficient Analysis in Stimulation Treatment Design

2014 ◽  
Vol 933 ◽  
pp. 202-205
Author(s):  
Bo Cai ◽  
Yun Hong Ding ◽  
Yong Jun Lu ◽  
Chun Ming He ◽  
Gui Fu Duan
Keyword(s):  
Hydraulic Fracturing ◽  
Field Method ◽  
Oil Field ◽  
Low Permeability ◽  
Analysis Model ◽  
Fracturing Fluid ◽  
Real Time Analysis ◽  
Fracturing Fluids ◽  
Common Technique ◽  
Treatment Design

Hydraulic fracturing was first used in the late 1940s and has become a common technique to enhance the production of low-permeability formations.Hydraulic fracturing treatments were pumped into permeable formations with permeable fluids. This means that as the fracturing fluid was being pumped into the formation, a certain proportion of this fluid will being lost into formation as fluid leak-off. Therefore, leak-off coefficient is the most leading parameters of fracturing fluids. The accurate understanding of leak-off coefficient of fracturing fluid is an important guidance to hydraulic fracturing industry design. In this paper, a new field method of leak-off coefficient real time analysis model was presented based on instantaneous shut-in pressure (ISIP). More than 100 wells were fractured using this method in oil field. The results show that average liquid rates of post-fracturing was 22m3/d which double improvement compared with the past treatment wells. It had an important role for hydraulic fracturing stimulation treatment design in low permeability reservoirs and was proven that the new model for hydraulic fracturing treatment is greatly improved.

scholarly journals Modeling Hydraulic Fracturing Using Natural Gas Foam as Fracturing Fluids

Energies ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7645
Author(s):  
Shuang Zheng ◽  
Mukul M. Sharma
Keyword(s):  
Equation Of State ◽  
Natural Gas ◽  
Hydraulic Fracturing ◽  
Gas Emission ◽  
Fracturing Fluid ◽  
Fracturing Fluids ◽  
Water Based ◽  
Simulation Results ◽  
The Cost ◽  
Stranded Gas

Stranded gas emission from the field production because of the limitations in the pipeline infrastructure has become one of the major contributors to the greenhouse effects. How to handle the stranded gas is a troublesome problem under the background of global “net-zero” emission efforts. On the other hand, the cost of water for hydraulic fracturing is high and water is not accessible in some areas. The idea of using stranded gas in replace of the water-based fracturing fluid can reduce the gas emission and the cost. This paper presents some novel numerical studies on the feasibility of using stranded natural gas as fracturing fluids. Differences in the fracture creating, proppant placement, and oil/gas/water flowback are compared between natural gas fracturing fluids and water-based fracturing fluids. A fully integrated equation of state compositional hydraulic fracturing and reservoir simulator is used in this paper. Public datasets for the Permian Basin rock and fluid properties and natural gas foam properties are collected to set up simulation cases. The reservoir hydrocarbon fluid and natural gas fracturing fluids phase behavior is modeled using the Peng-Robinson equation of state. The evolving of created fracture geometry, conductivity and flowback performance during the lifecycle of the well (injection, shut-in, and production) are analyzed for the gas and water fracturing fluids. Simulation results show that natural gas and foam fracturing fluids are better than water-based fracturing fluids in terms of lower breakdown pressure, lower water leakoff into the reservoir, and higher cluster efficiency. NG foams tend to create better propped fractures with shorter length and larger width, because of their high viscosity. NG foam is also found to create better stimulated rock volume (SRV) permeability, better fracturing fluid flowback with a large water usage reduction, and high natural gas consumption. The simulation results presented in this paper are helpful to the operators in reducing natural gas emission while reducing the cost of hydraulic fracturing operation.

scholarly journals A Novel Hydraulic Fracturing Method Based on the Coupled CFD-DEM Numerical Simulation Study

2020 ◽  
Vol 10 (9) ◽  
pp. 3027
Author(s):  
Cong Lu ◽  
Li Ma ◽  
Zhili Li ◽  
Fenglan Huang ◽  
Chuhao Huang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Hydraulic Fracturing ◽  
Variable Viscosity ◽  
Oil Reservoirs ◽  
Fluid Viscosity ◽  
Low Density ◽  
Fracturing Fluid ◽  
Proppant Transport ◽  
Fracturing Fluids ◽  
Transport Experiment

For the development of tight oil reservoirs, hydraulic fracturing employing variable fluid viscosity and proppant density is essential for addressing the problems of uneven placement of proppants in fractures and low propping efficiency. However, the influence mechanisms of fracturing fluid viscosity and proppant density on proppant transport in fractures remain unclear. Based on computational fluid dynamics (CFD) and the discrete element method (DEM), a proppant transport model with fluid–particle two-phase coupling is established in this study. In addition, a novel large-scale visual fracture simulation device was developed to realize the online visual monitoring of proppant transport, and a proppant transport experiment under the condition of variable viscosity fracturing fluid and proppant density was conducted. By comparing the experimental results and the numerical simulation results, the accuracy of the proppant transport numerical model was verified. Subsequently, through a proppant transport numerical simulation, the effects of fracturing fluid viscosity and proppant density on proppant transport were analyzed. The results show that as the viscosity of the fracturing fluid increases, the length of the “no proppant zone” at the front end of the fracture increases, and proppant particles can be transported further. When alternately injecting fracturing fluids of different viscosities, the viscosity ratio of the fracturing fluids should be adjusted between 2 and 5 to form optimal proppant placement. During the process of variable proppant density fracturing, when high-density proppant was pumped after low-density proppant, proppants of different densities laid fractures evenly and vertically. Conversely, when low-density proppant was pumped after high-density proppant, the low-density proppant could be transported farther into the fracture to form a longer sandbank. Based on the abovementioned observations, a novel hydraulic fracturing method is proposed to optimize the placement of proppants in fractures by adjusting the fracturing fluid viscosity and proppant density. This method has been successfully applied to more than 10 oil wells of the Bohai Bay Basin in Eastern China, and the average daily oil production per well increased by 7.4 t, significantly improving the functioning of fracturing. The proppant settlement and transport laws of proppant in fractures during variable viscosity and density fracturing can be efficiently revealed through a visualized proppant transport experiment and numerical simulation study. The novel fracturing method proposed in this study can significantly improve the hydraulic fracturing effect in tight oil reservoirs.

scholarly journals Generalized Extreme Value Statistics, Physical Scaling and Forecasts of Oil Production in the Bakken Shale

Energies ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3641 ◽  
Author(s):  
Wardana Saputra ◽  
Wissem Kirati ◽  
Tadeusz Patzek
Keyword(s):  
Oil Production ◽  
Extreme Value ◽  
Gas Production ◽  
Extreme Value Statistics ◽  
Well Performance ◽  
Generalized Extreme Value ◽  
Potential Wells ◽  
Well Production ◽  
Industry Standard ◽  
Decline Curve

We aim to replace the current industry-standard empirical forecasts of oil production from hydrofractured horizontal wells in shales with a statistically and physically robust, accurate and precise method of matching historic well performance and predicting well production for up to two more decades. Our Bakken oil forecasting method extends the previous work on predicting fieldwide gas production in the Barnett shale and merges it with our new scaling of oil production in the Bakken. We first divide the existing 14,678 horizontal oil wells in the Bakken into 12 static samples in which reservoir quality and completion technologies are similar. For each sample, we use a purely data-driven non-parametric approach to arrive at an appropriate generalized extreme value (GEV) distribution of oil production from that sample’s dynamic well cohorts with at least 1 , 2 , 3 , ⋯ years on production. From these well cohorts, we stitch together the P 50 , P 10 , and P 90 statistical well prototypes for each sample. These statistical well prototypes are conditioned by well attrition, hydrofracture deterioration, pressure interference, well interference, progress in technology, and so forth. So far, there has been no physical scaling. Now we fit the parameters of our physical scaling model to the statistical well prototypes, and obtain a smooth extrapolation of oil production that is mechanistic, and not just a decline curve. At late times, we add radial inflow from the outside. By calculating the number of potential wells per square mile of each Bakken region (core and noncore), and scheduling future drilling programs, we stack up the extended well prototypes to obtain the plausible forecasts of oil production in the Bakken. We predict that Bakken will ultimately produce 5 billion barrels of oil from the existing wells, with the possible addition of 2 and 6 billion barrels from core and noncore areas, respectively.

Optimization of Fracturing Fluid Flowback Based on Fluid Mechanics for Multilayer Fractured Tight Reservoir

2014 ◽  
Vol 886 ◽  
pp. 448-451 ◽  
Author(s):  
Hai Yong Zhang ◽  
Dai Hong Gu ◽  
Ming Zhu ◽  
Shun Li He ◽  
Cheng Quan Men ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Fluid Mechanics ◽  
Field Data ◽  
Theoretical Models ◽  
Sand Production ◽  
Fracturing Fluid ◽  
Wellhead Pressure ◽  
Production Ratio ◽  
Tight Reservoir

The purpose of frac fluid flowback is to outflow the fracturing fluid and prevent the proppant backflow, which determines the effect of fracturing fluid flowback. The fracturing treatment in field lacks relevant theoretical models for prediction. Therefore, this work focuses on establishing the flowback model of hydraulic fracturing for multilayer fractured wells. Then the wellhead pressure and fluid flowback volume are predicted based on the actual parameters of fracturing treatment in the process of flowback and are compared with the field data of frac fluid flowback. Results show that the wellhead pressure and fluid flowback volume calculated by the model are consistent with the field data. The sand production ratio of the three wells during the flowback process is lower than 1% indicating that the optimized parameters achieve the purpose of flowback operations and reduce the flowback volume of the proppant.

In vitro cytotoxicity assessment of a hydraulic fracturing fluid

2015 ◽  
Vol 12 (3) ◽  
pp. 286 ◽  
Author(s):  
Madeleine E. Payne ◽  
Heather F. Chapman ◽  
Janet Cumming ◽  
Frederic D. L. Leusch
Keyword(s):  
Coal Seam ◽  
Hydraulic Fracturing ◽  
Human Health ◽  
Produced Water ◽  
Coal Seam Gas ◽  
Fracturing Fluid ◽  
Human Health Risks ◽  
Fracturing Fluids ◽  
Hydraulic Fracturing Fluid

Environmental context Hydraulic fracturing fluids, used in large volumes by the coal seam gas mining industry, are potentially present in the environment either in underground formations or in mine wastewater (produced water). Previous studies of the human health and environmental effects of this practice have been limited because they use only desktop methods and have not considered combined mixture toxicity. We use a novel in vitro method for toxicity assessment, and describe the toxicity of a hydraulic fracturing fluid on a human gastrointestinal cell line. Abstract Hydraulic fracturing fluids are chemical mixtures used to enhance oil and gas extraction. There are concerns that fracturing fluids are hazardous and that their release into the environment – by direct injection to coal and shale formations or as residue in produced water – may have effects on ecosystems, water quality and public health. This study aimed to characterise the acute cytotoxicity of a hydraulic fracturing fluid using a human gastrointestinal cell line and, using this data, contribute to the understanding of potential human health risks posed by coal seam gas (CSG) extraction in Queensland, Australia. Previous published research on the health effects of hydraulic fracturing fluids has been limited to desktop studies of individual chemicals. As such, this study is one of the first attempts to characterise the toxicity of a hydraulic fracturing mixture using laboratory methods. The fracturing fluid was determined to be cytotoxic, with half maximal inhibitory concentrations (IC50) values across mixture variations ranging between 25 and 51mM. When used by industry, these fracturing fluids would be at concentrations of over 200mM before injection into the coal seam. A 5-fold dilution would be sufficient to reduce the toxicity of the fluids to below the detection limit of the assay. It is unlikely that human exposure would occur at these high (‘before use’) concentrations and likely that the fluids would be diluted during use. Thus, it can be inferred that the level of acute risk to human health associated with the use of these fracturing fluids is low. However, a thorough exposure assessment and additional chronic and targeted toxicity assessments are required to conclusively determine human health risks.

scholarly journals Supramolecular dynamic binary complexes with pH and salt-responsive properties for use in unconventional reservoirs

PLoS ONE ◽  
2021 ◽  
Vol 16 (12) ◽  
pp. e0260786
Author(s):  
Bhargavi Bhat ◽  
Shuhao Liu ◽  
Yu-Ting Lin ◽  
Martin L. Sentmanat ◽  
Joseph Kwon ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Self Assembly ◽  
Energy Demand ◽  
Unconventional Reservoirs ◽  
Binary Complex ◽  
Fracturing Fluid ◽  
Zero Shear Viscosity ◽  
Fracturing Fluids ◽  
Binary Complexes ◽  
Alkaline Conditions

Hydraulic fracturing of unconventional reservoirs has seen a boom in the last century, as a means to fulfill the growing energy demand in the world. The fracturing fluid used in the process plays a substantial role in determining the results. Hence, several research and development efforts have been geared towards developing more sustainable, efficient, and improved fracturing fluids. Herein, we present a dynamic binary complex (DBC) solution, with potential to be useful in the hydraulic fracturing domain. It has a supramolecular structure formed by the self-assembly of low molecular weight viscosifiers (LMWVs) oleic acid and diethylenetriamine into an elongated entangled network under alkaline conditions. With less than 2 wt% constituents dispersed in aqueous solution, a viscous gel that exhibits high viscosities even under shear was formed. Key features include responsiveness to pH and salinity, and a zero-shear viscosity that could be tuned by a factor of ~280 by changing the pH. Furthermore, its viscous properties were more pronounced in the presence of salt. Sand settling tests revealed its potential to hold up sand particles for extended periods of time. In conclusion, this DBC solution system has potential to be utilized as a smart salt-responsive, pH-switchable hydraulic fracturing fluid.

scholarly journals FORMATION HYDRAULIC FRACTURING FLUID BASED ON CARBOXYMETHYL CELLULOSE: ITS ADVANTAGES AND LIMITATIONS, APPLICATION PROSPECTS

2016 ◽  
pp. 49-57
Author(s):  
V. R. Kalinin
Keyword(s):  
Hydraulic Fracturing ◽  
Carboxymethyl Cellulose ◽  
Low Cost ◽  
Low Permeability ◽  
Laboratory Studies ◽  
Fracturing Fluid ◽  
Fracturing Fluids ◽  
Low Permeability Reservoirs ◽  
Manufacturing Features ◽  
Hydraulic Fracturing Fluid

The article considers the advantages and limitations of hydraulic fracturing fluid based on carboxymethyl cellulose determined as a result of laboratory studies. As a result of testing the studied fluid manufacturing features compared with similar fracturing fluids it was determined that the fluid of interest can be effectively used as a fluid for formation hydraulic fracturing especially in low permeability reservoirs. This fluid is widely available and has a low cost. It can easily replace the foreign analogues.

Sign in / Sign up

Export Citation Format

Share Document