scholarly journals Shaking Table Tests of Lead Inserted Small-Sized Laminated Rubber Bearing for Nuclear Component Seismic Isolation

2021 ◽  
Vol 11 (10) ◽  
pp. 4431
Author(s):  
Gyeong-Hoi Koo ◽  
Tae-Myung Shin ◽  
Sang-Jin Ma
Keyword(s):  
Dynamic Characteristics ◽  
Seismic Isolation ◽  
Shaking Table ◽  
Design Parameters ◽  
Shaking Table Tests ◽  
High Frequency Region ◽  
Mass System ◽  
Design Basis ◽  
Rubber Bearings ◽  
Isolation Performance

To assure seismic isolation performance against design and beyond design basis earthquakes in the nuclear facility components, the lead inserted small-sized laminated rubber bearings (LRB), which has a 10 kN vertical design load, have been designed and quasi-statically tested to validate their design mechanical properties in previous studies. Following this study, the seismic shaking tests of these full-scale LRBs are performed and discussed in this paper with the dummy mass system to investigate actual seismic isolation performance, dynamic characteristics of LRBs, consistency of the LRB’s quality, and so on. To study the seismic isolation performance, three beam structures (S1–S3) with different natural frequencies were installed both on the shaking table and the dummy mass supported by four LRBs: (1) S1: structure close to seismic isolation frequency; (2) S2: structure close to peak input spectral frequency; (3) S3: structure in the high-frequency region. The test results are described in various seismic levels of OBE (Operating Basis Earthquake), SSE (Safe Shutdown Earthquake), and BDBE (Beyond Design Basis Earthquake), and are compared with the analysis results to assure the seismic isolation performance and the LRB’s design parameters. From the results of the shaking table tests, it is confirmed that the lead inserted small-sized LRBs reveal an adequate seismic isolation performance and their dynamic characteristics as intended in the LRB design.

Shaking Table Tests With Large Test Specimens of Seismically Isolated FBR Plants: Part 2—Damage Test of Reinforced Concrete Wall Structure

2009 ◽  
Author(s):  
Satoru Inaba ◽  
Takuya Anabuki ◽  
Kazutaka Shirai ◽  
Shuichi Yabana ◽  
Seiji Kitamura
Keyword(s):  
Reinforced Concrete ◽  
Seismic Isolation ◽  
Shaking Table Test ◽  
Shaking Table ◽  
Wall Structure ◽  
Shaking Table Tests ◽  
Concrete Wall ◽  
Restoring Force ◽  
Seismically Isolated ◽  
Rubber Bearings

This paper describes the dynamic damage test of a reinforced concrete (RC) wall structure with seismic isolation sysytem. It has been expected that seismically isolated structures are damaged in sudden when the accelerations of the structures exceed a certain level by hardening of the rubber bearings. However, the response behavior and the damage mode have not been observed by experimental test yet. So, shaking table tests were carried out at “E-Defense”, equipping the world’s largest shaking table, located at Miki City, Hyogo prefecture, Japan. The specimen was composed of an upper structure of 600 ton by weight and six lead-rubber bearings (LRBs) of 505 mm in diameter which provide both stiffness and hysteretic damping. The upper structure consisted of a RC mass and four RC walls with counter weight. The RC wall structure was designed so that the damage of the RC wall occurred between the shear force at the hardening of the rubber bearings and that at their breaking. The dimensions of the RC wall were 1600 × 800 × 100 mm (B × H × t). The reinforcement ratios were 2.46% in vertical by D13 (deformed reinforcing bar, 13 mm in diameter) and 1.0% in horizontal by D10. The shaking table test was conducted consecutively by increasing the levels up to 225% of tentative design earthquake motion. Consequently, because of the increase of the structural response by the hardening of the rubber bearings, the damage of the wall structure with seismic isolation system suddenly happened. In addition, the preliminary finite element analysis simulated the test results fairly well, which were the restoring force characteristics, the crack patterns of the RC wall structure and such.

scholarly journals Experimental Approach for the Failure Mode of Small Laminated Rubber Bearings for Seismic Isolation of Nuclear Components

2021 ◽  
Vol 12 (1) ◽  
pp. 125
Author(s):  
Sang-Jin Ma ◽  
Tae-Myung Shin ◽  
Ju-Seung Ryu ◽  
Jin-Hyeong Lee ◽  
Gyeong-Hoi Koo
Keyword(s):  
Seismic Isolation ◽  
Response Spectrum ◽  
Shaking Table ◽  
Intensity Level ◽  
Shaking Table Tests ◽  
Response Characteristics ◽  
Water Jet Cutting ◽  
Total Failure ◽  
Rubber Bearings ◽  
Partial Damage

Response characteristics of small-sized laminated rubber bearings (LRBs) with partial damage and total failure were investigated. For nuclear component seismic isolation, ultimate response characteristics are mainly reviewed using a beyond design basis earthquake (BDBE). Static tests, 3D shaking table tests, and verification analyses were performed using optional LRB design prototypes. During the static test, the hysteresis curve behavior from buckling to potential damage was observed by applying excessive shear deformation. The damaged rubber surface of the laminated section inside the LRB was checked through water jet cutting. A stress review by response spectrum analysis was performed to simulate the dynamic tests and predict seismic inputs’ intensity level that triggers LRB damage. Shaking table tests were executed to determine seismic response characteristics with partial damage and to confirm the stability of the superstructure when the supporting LRBs completely fail. Shear buckling in LRBs by high levels of BDBE may be quickly initiated via partial damage or total failure by the addition of torsional or rotational behavior caused by a change in the dynamic characteristics. Furthermore, the maximum seismic displacement can be limited within the range of the design interface due to the successive slip behavior, even during total LRB failure.

Shaking Table Tests With Large Test Specimens of Seismically Isolated FBR Plants: Part 3—Ultimate Behavior of Upper Structure and Rubber Bearings

2009 ◽  
Author(s):  
Shuichi Yabana ◽  
Kenji Kanazawa ◽  
Seiji Nagata ◽  
Seiji Kitamura ◽  
Takeshi Sano
Keyword(s):  
Seismic Isolation ◽  
Response Spectra ◽  
Shaking Table ◽  
Shaking Table Tests ◽  
Nuclear Facilities ◽  
Restoring Force ◽  
Isolation System ◽  
Seismically Isolated ◽  
Design Earthquake ◽  
Rubber Bearings

This paper describes results of shaking table tests to grasp ultimate behavior of seismic isolation system under extremely strong earthquake motions, including failure of rubber bearings. The results of the shaking table tests are expected to be useful for the design of seismically isolated nuclear facilities, especially fast breeder reactor (FBR) plants. In the test, lead rubber bearings, of which the diameter is 505 mm and about 1/3 scale of a prototype in planning FBR plants, are used; the test specimens are loaded by the largest three-dimensional shaking table in E-defense of National Research Institute for Earth Science and Disaster Prevention (NIED) of Japan. Failure of rubber bearings occurs with amplified tentative design earthquake motions. From the tests, the ultimate responses of the upper structure and rubber bearings are presented. In particular, the change of floor response spectra and restoring force characteristics of rubber bearings according to increase of input motions is discussed. Furthermore, mechanism of the failure of rubber bearings is investigated from the observation of failure surfaces and cut sections, static loading tests, and material tests of rubber bearings. Finally, the function of seismic isolation system after the failure of a part of rubber bearings is confirmed under the tentative design earthquake.

Geotechnical Seismic Isolation System - Further Experimental Study

2014 ◽  
Vol 580-583 ◽  
pp. 1490-1493 ◽  
Author(s):  
Wei Xiong ◽  
Ming Ren Yan ◽  
Yao Zhuang Li
Keyword(s):  
Experimental Study ◽  
Dynamic Response ◽  
Parametric Study ◽  
Seismic Isolation ◽  
Shaking Table ◽  
Shaking Table Tests ◽  
Seismic Acceleration ◽  
Isolation System ◽  
Isolation Performance

The isolation effectiveness of the Geotechnical Seismic Isolation (GSI) system was further investigated via a series of prescribed shaking-table tests. The dynamic response of GSI system was also evaluated in detail of this work. A parametric study for assessment of the isolation performance of GSI was conducted by varying experimental key parameters, such as rubber percentage of rubber-sand mixtures (RSM), configuration of the foundation, storey number of the superstructure, and different kinds of seismic acceleration inputs. From the parametric survey, it can be concluded that the GSI system can to some extent attenuate the dynamic response of the superstructure under big earthquake shakings.

Shaking Table Tests on a Spherical Tank Mock-Up Provided With Seismic Isolation and Flexible Piping Connections

2006 ◽  
Author(s):  
Massimo Forni ◽  
Alessandro Poggianti ◽  
Giulia Bergamo ◽  
Fabrizio Gatti
Keyword(s):  
Seismic Isolation ◽  
Shaking Table ◽  
Seismic Protection ◽  
Piping System ◽  
Fiber Reinforced ◽  
Shaking Table Tests ◽  
Fixed Base ◽  
High Damping Rubber ◽  
Isolation Systems ◽  
Rubber Bearings

The Project INDEPTH (Development of INnovative DEvices for Seismic Protection of PeTrocHemical Facilities), supported by the European Commission, has the objective of developing and applying innovative seismic isolation and/or dissipation systems for critical structures at petrochemical facilities. In the framework of INDEPTH, integrated seismic protection systems have been conceived, developed and tested. They are aimed at protecting liquid-filled structures (product storage, spherical and LNG tanks), with new devices (fiber-reinforced isolators, buckling reinforced braces) specific for each application and new flexible piping couplings, to compensate the displacements resulting from the use of isolation systems. The research program has been focused on the selection of critical structures, the design and manufacturing of the devices, the numerical assessment and the experimental validation through shaking table tests [1–4]. A quantification of technical/economical/safety benefits with respect to the conventional state-of-the-art measures presently adopted and potential application to retrofitting has been performed. This paper describes the validation through shaking table tests of the effectiveness of the isolation systems on a spherical mock-up and the related piping system equipped with flexible joints. Different configurations of the mock-up have been tested, such as: fixed base, isolated base with High Damping Rubber Bearings, Fiber Reinforced Rubber Bearings and Lead Rubber Bearings. Furthermore, each configuration has been tested for three different level of filling to verify the sloshing behavior in the sphere and the effectiveness of the isolation systems at filling levels different from the design one (full sphere).

Shaking Table Tests on a Spherical Tank Mock-Up Provided With Seismic Isolation and Flexible Piping Connections

2005 ◽  
Author(s):  
Massimo Forni
Keyword(s):  
Seismic Isolation ◽  
Shaking Table ◽  
Seismic Protection ◽  
Piping System ◽  
Fiber Reinforced ◽  
Shaking Table Tests ◽  
Time Histories ◽  
High Damping Rubber ◽  
Isolation Systems ◽  
Rubber Bearings

The Project INDEPTH (Development of INnovative DEvices for Seismic Protection of PeTrocHemical Facilities), supported by the European Commission, has the objective of developing and applying innovative seismic isolation and/or dissipation devices for critical structures at petrochemical facilities. In the framework of INDEPTH, integrated seismic protection systems have been conceived, developed and tested. They are aimed at protecting liquid-filled structures (product storage, spherical and LNG tanks), with new devices (fiber-reinforced isolators, buckling reinforced braces) specific for each application and new flexible piping couplings, to compensate the displacements resulting from the use of isolation systems. The research program has been focused on the selection of critical structures, the design and manufacturing of the devices, the numerical assessment and the experimental validation through shaking table tests. A quantification of technical/economical/safety benefits with respect to the conventional state-of-the-art measures presently adopted and potential application to retrofitting has been performed. Validation through shaking table tests of the effectiveness of the isolation systems on the spherical mock-up (Figure 1), and the related piping system equipped with flexible joints (Figure 2), had been performed. Two types of seismic input have been applied, both synthesized from the 5% damping spectra of EC8 (medium and soft soils); the target peak acceleration value of the time histories was 0.4 g. Different configurations of the mock-up have been tested, such as: fixed base, isolated base with High Damping Rubber Bearings, Fiber Reinforced Rubber Bearings and Lead Rubber Bearings. Furthermore, each configuration has been tested for both time histories and at three different level of filling to verify the sloshing behavior in the sphere and the effectiveness of the isolation systems at levels of filling different from the design one (full sphere). Comparison among all the above mentioned conditions could be done. The presentation will show the main results of the shaking table campaign.

Shaking Table Tests of Full Scale Base-Isolated Structures

2002 ◽  
Author(s):  
C. S. Tsai ◽  
B. J. Chen ◽  
T. C. Chiang
Keyword(s):  
Structural Control ◽  
Control Strategies ◽  
Steel Structure ◽  
Seismic Energy ◽  
Full Scale ◽  
Shaking Table ◽  
Shaking Table Tests ◽  
Natural Period ◽  
Rubber Bearing ◽  
Rubber Bearings

Conventional earthquake resistant designs depend on strengthen and ductility of the structural components to resist induced forces and to dissipate seismic energy. However, this can produce permanent damage to the joints as well as the larger interstory displacements. In recently years, many studies on structural control strategies and devices have been developed and applied in U. S. A., Europe, Japan, and New Zealand. The rubber bearing belongs to one kind of the earthquake-proof ideas of structural control technologies. The installation of rubber bearings can lengthen the natural period of a building and simultaneously reduce the earthquake-induced energy trying to impart to the building. They can reduce the magnitude of the earthquake-induced forces and consequently reduce damage to the structures and its contents, and reduce danger to its occupants. This paper is aimed at studying the mechanical behavior of the stirrup rubber bearings (SRB) and evaluating the feasibility of the buildings equipped with the stirrup rubber bearings. Furthermore, uniaxial, biaxial, and triaxial shaking table tests are conducted to study the seismic response of a full-scale three-story isolated steel structure. Experimental results indicate that the stirrup rubber bearings possess higher damping ratios at higher strains, and that the stirrup rubber bearings provide good protection for structures. It has been proved through the full-scale tests on shaking table that the stirrup rubber bearing is a very promising tool to enhance the seismic resistibility of structures.

Improved Model Tests to Investigate the Failure Modes of Pipes Under Beyond Design Basis Earthquakes

2018 ◽  
Author(s):  
Izumi Nakamura ◽  
Naoto Kasahara
Keyword(s):  
Failure Mode ◽  
Failure Modes ◽  
Shaking Table Test ◽  
Shaking Table ◽  
Piping System ◽  
Input Frequency ◽  
Shaking Table Tests ◽  
Pure Lead ◽  
Design Basis ◽  
Improved Model

In order to investigate the failure modes of piping systems under the beyond design basis seismic loads, the authors proposed an experimental approach to use pipes made of the simulation material instead of steel pipes in the previous study. Though the ratchet-collapse (ratchet and subsequent collapse) was successfully obtained as the failure mode through the shaking table test using the pure lead (Pb) pipes as the simulation material pipe specimens, there was concern that characteristics of pure lead was somewhat extreme considering the analogy with the stress-strain relationship of steel. In order to resolve such concern, a modified experimental procedure has been developed. In the modified procedure, lead-antimony (Pb-Sb) alloy is used as the simulation material. Through the shaking table tests on single elbow pipe specimens made of Pb-Sb alloy, it is found that the typical failure mode is the ratchet and subsequent collapse, as same as the results by the shaking table tests of the Pb pipe specimens. The results indicate that the lower input frequency than the specimen’s natural frequency is prone to cause failure to the specimen, while the higher input frequency hardly causes the failure. The tendency of the global behavior of specimens is similar each other between the Pb pipe specimens and the Pb-Sb alloy specimens, but the strength of self-weight collapse of the Pb-Sb alloy pipe specimen is much higher than that of the Pb pipe specimen. Due to such higher strength of Pb-Sb alloy pipes, a prospect to conduct an excitation test on a more complicated piping system model is obtained.

Study on First-Floor Isolated Structure with Metallic Damper

2012 ◽  
Vol 446-449 ◽  
pp. 3042-3045
Author(s):  
Jin Bao Ji ◽  
Zhi Wei Ni ◽  
Yang Yang Du ◽  
Yang Qiang Fu
Keyword(s):  
Finite Element Analysis ◽  
Structural Model ◽  
Southern China ◽  
Shaking Table ◽  
Shaking Table Tests ◽  
Element Analysis ◽  
Damping Rate ◽  
Metallic Dampers ◽  
Rubber Bearings ◽  
Metallic Damper

As an advancing isolation technology, the first-floor isolated structure can take full use of the first-floor space, and has been promoted in southern China gradually. To study the isolation effect of the first-floor isolated structure and to improve the damping rate of it, a seven-story structural model with laminated rubber bearings and metallic dampers installed on the top of first-floor columns was studied by shaking table tests and finite element analysis using SAP2000 API. The results of the tests and analysis show that the isolation technology with metallic dampers can reduce the seismic response of the upper structure significantly.

Experimental Study of a Multiple Bay Structure Isolated With Hybrid Bearings

2003 ◽  
Author(s):  
C. S. Tsai ◽  
Bo-Jen Chen ◽  
Tsu-Cheng Chiang ◽  
Guan-Hsing Lee
Keyword(s):  
Earthquake Engineering ◽  
Base Isolation ◽  
Steel Structure ◽  
Seismic Energy ◽  
Shaking Table ◽  
Element Formulation ◽  
Shaking Table Tests ◽  
Seismic Responses ◽  
Promising Tool ◽  
Rubber Bearings

In conventional earthquake resistance design approach (the ductility-design philosophy), the energy dissipation mechanism is based on plastic deformations at scattered locations in the structure. However, this can produce permanent damage to the joints as well as the larger interstory displacements. In recently years, the base isolation technology has been adopted as a feasible and attractive way in improving seismic resistance of structures. It can shift the natural periods of structures away from the rich periods contents of earthquake motions, but also provide considerable supplemental damping to dissipate seismic energy transmitted into structures during earthquakes. In this paper, uniaxial, biaxial, and triaxial shaking table tests are performed to study the seismic behavior of a 0.4-scale three-story isolated steel structure in the National Center for Research on Earthquake Engineering in Taiwan. Experimental results demonstrate that structures with hybrid rubber bearings can actually decrease the seismic responses of the superstructure. It has been proved through the shaking table tests that the rubber bearing is a very promising tool to enhance the seismic resistibility of structures. Moreover, it is illustrated that the proposed analytical model and finite element formulation in this paper can well predict the mechanical behavior of rubber bearings and seismic responses of the base-isolated structures.

Sign in / Sign up

Export Citation Format

Share Document