scholarly journals Proposed Models to Improve Predicting the Operating Temperature of Different Photovoltaic Module Technologies under Various Climatic Conditions

2021 ◽  
Vol 11 (15) ◽  
pp. 7064
Author(s):  
Dang Phuc Nguyen Nguyen ◽  
Kristiaan Neyts ◽  
Johan Lauwaert
Keyword(s):  
Wind Speed ◽  
Crystalline Silicon ◽  
Operating Temperature ◽  
Thermal Inertia ◽  
Climatic Conditions ◽  
Solar Irradiation ◽  
Photovoltaic Module ◽  
Silicon Thin Film ◽  
Pv Module ◽  
Pv Modules

The operating temperature is an essential parameter determining the performance of a photovoltaic (PV) module. Moreover, the estimation of the temperature in the absence of measurements is very complex, especially for outdoor conditions. Fortunately, several models with and without wind speed have been proposed to predict the outdoor operating temperature of a PV module. However, a problem for these models is that their accuracy decreases when the sampling interval is smaller due to the thermal inertia of the PV modules. In this paper, two models, one with wind speed and the other without wind speed, are proposed to improve the precision of estimating the operating temperature of outdoor PV modules. The innovative aspect of this study is two novel thermal models that consider the variation of solar irradiation over time and the thermal inertia of the PV module. The calculation is applied to different types of PV modules, including crystalline silicon, thin film as well as tandem technology at different locations. The models are compared to models that are described in the literature. The results obtained in different time steps show that our proposed models achieve better performance and can be applied to different PV technologies.

Thermal Patterns in PV Arrays Operating in Tropical Conditions: A Preliminary Approach

2013 ◽  
Author(s):  
Rolando Soler-Bientz ◽  
Lifter Ricalde-Cab ◽  
Inés Riech Méndez
Keyword(s):  
Wind Speed ◽  
Crystalline Silicon ◽  
Geographical Location ◽  
Temperature Sensors ◽  
Research System ◽  
Pv Array ◽  
Pv Module ◽  
Tropical Conditions ◽  
Pv Modules ◽  
Thermal Patterns

This paper presents preliminary results of a field study focused in the study of the heat patterns of a PV array in tropical conditions. The research system is comprised by four sub arrays of four mono-crystalline Silicon PV Modules. The system was installed facing to the South direction in a static configuration according to the geographical location of the study site. A set of temperature sensors were installed on the back of the PV module in order to monitor their thermal patterns on daily basics. Ambient temperature, solar radiation on the PV surface and on the horizontal surface as well as the wind speed and wind direction have been also monitored concurrently with the thermal patterns of the whole PV array under study.

scholarly journals Photovoltaic Module Electrical Efficiency Enhancement Using Nano Fluids and Nano-Paraffin

2022 ◽  
Vol 961 (1) ◽  
pp. 012065
Author(s):  
“Miqdam T Chaichan ◽  
Muhaned A H Zaidi ◽  
Hussein A. Kazem ◽  
K. Sopian
Keyword(s):  
High Temperature ◽  
Fossil Fuels ◽  
High Efficiency ◽  
Climatic Conditions ◽  
Hot Water ◽  
Photovoltaic Module ◽  
Photovoltaic Panel ◽  
Electrical Efficiency ◽  
Pv Module ◽  
Pv Modules

Abstract Today, photovoltaic modules have become accepted by the public and scientists in the production of clean electricity and as a possible alternative to electricity produced from fossil fuels. These modules suffer from a deterioration in their electrical efficiency as a result of their high temperature. Several researchers have proposed the use of high-efficiency hybrid photovoltaic (PV/T) systems that can cool PV modules and also produce hot water. Improving the PV modules’ electrical efficiency increases the investment attraction and commercialization of this technology. The possibility of restoring the electrical efficiency of the photovoltaic panel that was lost due to its high temperature was investigated in this study. A PV/T system designed to operate with a paraffin-filled thermal tank attached to the PV module was used. Inside the paraffin is a heat exchanger that circulates inside a nanofluid. This design is adopted to cool down the PV module temperature. The study was carried out in the climatic conditions of the month of May in the city of Baghdad - Iraq. The proposed PV/T system’s electrical efficiency was compared with similar systems from the literature. The proposed system has achieved an obvious enhancement as its electrical efficiency was 13.7%.

Performansi aktual modul photovoltaik dengan pengarah matahari

2018 ◽  
Vol 12 (2) ◽  
pp. 98 ◽  
Author(s):  
Jalaluddin . ◽  
Baharuddin Mire
Keyword(s):  
Solar Radiation ◽  
Local Time ◽  
Performance Characteristic ◽  
Electrical Energy ◽  
Photovoltaic Module ◽  
Experiment Data ◽  
Actual Performance ◽  
Pv Module ◽  
Solar Tracking ◽  
Pv Modules

Actual performance of photovoltaic module with solar tracking is presented. Solar radiation can be converted into electrical energy using photovoltaic (PV) modules. Performance of polycristalline silicon PV modules with and without solar tracking are investigated experimentally. The PV module with dimension 698 x 518 x 25 mm has maximum power and voltage is 45 Watt and 18 Volt respectively. Based on the experiment data, it is concluded that the performance of PV module with solar tracking increases in the morning and afternoon compared with that of fixed PV module. It increases about 18 % in the morning from 10:00 to 12:00 and in the afternoon from 13:30 to 14:00 (local time). This study also shows the daily performance characteristic of the two PV modules. Using PV module with solar tracking provides a better performance than fixed PV module. 

Lifetime Estimation of a Photovoltaic Module Subjected to Corrosion Due to Damp Heat Testing

2012 ◽  
Vol 135 (2) ◽  
Author(s):  
R. Laronde ◽  
A. Charki ◽  
D. Bigaud
Keyword(s):  
Crystalline Silicon ◽  
Meteorological Data ◽  
Photovoltaic Module ◽  
Model Parameters ◽  
Solar Panels ◽  
Power Requirement ◽  
Pv Module ◽  
Accelerated Life ◽  
Mean Lifetime ◽  
Initial Power

In this paper, a methodology is presented for estimating the lifetime of a photovoltaic (PV) module. Designers guarantee an acceptable level of power (80% of the initial power) up to 25 yr for solar panels without having sufficient feedback to validate this lifetime. Accelerated life testing (ALT) can be carried out in order to determine the lifetime of the equipment. Severe conditions are used to accelerate the ageing of components and the reliability is then deduced in normal conditions, which are considered to be stochastic rather than constant. Environmental conditions at normal operations are simulated using IEC 61725 standard and meteorological data. The mean lifetime of a crystalline-silicon photovoltaic module that meets the minimum power requirement is estimated. The main results show the influence of lifetime distribution and Peck model parameters on the estimation of the lifetime of a photovoltaic module.

Effect of Unglazed Transpired Collector on the Performance of a Polycrystalline Silicon Photovoltaic Module

2006 ◽  
Vol 128 (3) ◽  
pp. 349-353 ◽  
Author(s):  
A. T. Naveed ◽  
E. C. Kang ◽  
E. J. Lee
Keyword(s):  
Polycrystalline Silicon ◽  
Electrical Power ◽  
Heating System ◽  
Photovoltaic Module ◽  
Forced Ventilation ◽  
Pv System ◽  
Pv Module ◽  
Pv Modules ◽  
Typical Day ◽  
Electrical Output

The electrical power generated by a polycrystalline silicon photovoltaic (PV) module mounted on an unglazed transpired solar collector (UTC) has been studied and compared to that of a PV module without UTC for a quantitative analysis of electrical output and its role in reducing the simple payback periods of photovoltaic electrical systems. A 75W polycrystalline silicon PV module was fixed on an UTC in front of the ventilation fan, and effectiveness of cooling by means of the forced ventilation at the rate of 160CFM was monitored. The temperature reduction under forced ventilation was in the range of 3-9°C with a 5% recovery in the electrical output power on a typical day of the month of February 2005. The simulated and measured electrical power outputs are in reasonable agreement with root-mean-square error of 2.40. The life cycle assessment of a hypothetical PV system located at Daejeon, South Korea and consisting of 3kW PV modules fixed on a 50m2 UTC shows that with a possible reduction of 3-9°C in the operating temperatures, the system requires three 75W fewer PV modules. The simple payback period of PV system is reduced from 23yearsto15years when integrated into an UTC air heating system.

scholarly journals An analysis of temperature distribution in solar photovoltaic module under various environmental conditions

2018 ◽  
Vol 240 ◽  
pp. 04004 ◽  
Author(s):  
Marek Jaszczur ◽  
Qusay Hassan ◽  
Janusz Teneta ◽  
Ewelina Majewska ◽  
Marcin Zych
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Wind Speed ◽  
Solar Radiation ◽  
Environmental Conditions ◽  
Operating Temperature ◽  
Photovoltaic Module ◽  
Solar Photovoltaic ◽  
System Efficiency ◽  
Pv System

The operating temperature of the photovoltaic module is an important issue because it is directly linked with system efficiency. The objective of this work is to evaluate temperature distribution in the photovoltaic module under different environmental conditions. The results shown that photovoltaic module operating temperature depends not only on the ambient temperature or solar radiation dependent but also depends on wind speed and wind direction. It is presented that the mounting conditions which are not taken into consideration by most of the literature models also play a significant role in heat transfer. Depends on mounting type an increase in module operating temperature in the range 10-15oC was observed which cause further PV system efficiency decrease of about 3.8-6.5 %.

scholarly journals Feasibility Study of the Technical and Economic Performance of Grid-Connected PV System for Selected Rooftops in UTHM

2021 ◽  
Vol 2 (2) ◽  
Author(s):  
Mohamad Fakrie Mohamad Ali ◽  
◽  
Mohd Noor Abdullah ◽  
Keyword(s):  
Feasibility Study ◽  
Crystalline Silicon ◽  
Electricity Consumption ◽  
Payback Period ◽  
Net Energy ◽  
Pv System ◽  
Pv Module ◽  
Electricity Bill ◽  
Pv Modules ◽  
Energy Metering

This paper presents the feasibility study of the technical and economic performances of grid-connected photovoltaic (PV) system for selected rooftops in Universiti Tun Hussein Onn Malaysia (UTHM). The analysis of the electricity consumption and electricity bill data of UTHM campus show that the monthly electricity usage in UTHM campus is very high and expensive. The main purpose of this project is to reduce the annual electricity consumption and electricity bill of UTHM with Net Energy Metering (NEM) scheme. Therefore, the grid-connected PV system has been proposed at Dewan Sultan Ibrahim (DSI), Tunku Tun Aminah Library (TTAL), Fakulti Kejuruteraan Awam dan Alam Bina (FKAAS) and F2 buildings UTHM by using three types of PV modules which are mono-crystalline silicon (Mono-Si), poly-crystalline silicon (Poly-Si) and Thin-film. These three PV modules were modeled, simulated and calculated using Helioscope software with the capacity of 2,166.40kWp, 2,046.20kWp and 1,845kWp respectively for the total rooftop area of 190,302.9 ft². The economic analysis was conducted on the chosen three installed PV modules using RETScreen software. As a result, the Mono-Si showed the best PV module that can produce 2,332,327.40 kWh of PV energy, 4.4% of CO₂ reduction, 9.3 years of payback period considering 21 years of the contractual period and profit of RM4,932,274.58 for 11.7 years after payback period. Moreover, the proposed installation of 2,166.40kWp (Mono-SI PV module) can reduce the annual electricity bill and CO2 emission of 3.6% (RM421,561.93) and 4.4% (1,851.40 tCO₂) compared to the system without PV system.

scholarly journals Modeling of Photovoltaic Module Using the MATLAB

2019 ◽  
Vol 9 ◽  
pp. 59-69
Author(s):  
Alok Dhaundiyal ◽  
Divine Atsu
Keyword(s):  
Standard Test ◽  
Electrical Performance ◽  
Photovoltaic Module ◽  
Solar Pv ◽  
Pv Module ◽  
Proposed Model ◽  
Current Voltage ◽  
Pv Modules ◽  
The Impact ◽  
The Mathematical Model

This paper presents the modeling and simulation of the characteristics and electrical performance of photovoltaic (PV) solar modules. Genetic coding is applied to obtain the optimized values of parameters within the constraint limit using the software MATLAB. A single diode model is proposed, considering the series and shunt resistances, to study the impact of solar irradiance and temperature on the power-voltage (P-V) and current-voltage (I-V) characteristics and predict the output of solar PV modules. The validation of the model under the standard test conditions (STC) and different values of temperature and insolation is performed, as well as an evaluation using experimentally obtained data from outdoor operating PV modules. The obtained results are also subjected to comply with the manufacturer’s data to ensure that the proposed model does not violate the prescribed tolerance range. The range of variation in current and voltage lies in the domain of 8.21 – 8.5 A and 22 – 23 V, respectively; while the predicted solutions for current and voltage vary from 8.28 – 8.68 A and 23.79 – 24.44 V, respectively. The measured experimental power of the PV module estimated to be 148 – 152 W is predicted from the mathematical model and the obtained values of simulated solution are in the domain of 149 – 157 W. The proposed scheme was found to be very effective at determining the influence of input factors on the modules, which is difficult to determine through experimental means.

Sign in / Sign up

Export Citation Format

Share Document