scholarly journals Physico-Mechanical Properties of Particleboards Produced from Macadamia Nutshell and Gum Arabic

2021 ◽  
Vol 11 (23) ◽  
pp. 11138
Author(s):  
Derrick Mirindi ◽  
Richard O. Onchiri ◽  
Joseph Thuo
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Gum Arabic ◽  
Physical And Mechanical Properties ◽  
General Purpose ◽  
Modulus Of Rupture ◽  
Thickness Swelling ◽  
X Ray ◽  
Electron Microscopy Analysis ◽  
Microscopy Analysis

Due to the rising prices and high demand for panels and the fact that formaldehyde—a known carcinogen—is used to manufacture conventional particleboard, this study investigated the suitability of particleboard formed from ground macadamia nutshells mixed with 50%, 40%, 30%, and 20% of gum Arabic and determined its physical and mechanical properties. The specific gravity, the bulk density, the x-ray fluorescence, and the scanning electron microscopy analysis of the two materials were analyzed. After production, the particleboards were cured for 56 days in an acclimatized room; then, the physical and mechanical properties were evaluated. Particleboards mixed with 50% gum Arabic and 50% macadamia nutshell showed good results in terms of the lowest average values of water absorption (9.42%) and thickness swelling (6.22%) after 24 h of immersion in distilled water as well as the highest density (1219.20 kg/m3), modulus of rupture (12.21 MPa), modulus of elasticity (1.81 GPa), internal bond strength (1.25 MPa), and compressive strength (22.54 MPa). According to ANSI/A208.1-1999, the particleboards produced met the standard for general-purpose boards except for water absorption (WA) and thickness swelling (TS) characteristics, which were above the maximum of 8% and 3%, respectively.

scholarly journals INFLUENCE OF THERMAL MODIFICATION ON THE PHYSICAL AND MECHANICAL PROPERTIES OF Eucalyptus badjensis MIXED PARTICLEBOARD / OSB PANELS

FLORESTA ◽  
2021 ◽  
Vol 51 (2) ◽  
pp. 419
Author(s):  
Giuliano Ferreira Pereira ◽  
Setsuo Iwakiri ◽  
Rosilani Trianoski ◽  
Polliana D'angelo Rios ◽  
Renan Zunta Raia
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Phenol Formaldehyde ◽  
Physical And Mechanical Properties ◽  
Dry Mass ◽  
Thermal Modification ◽  
Modulus Of Rupture ◽  
Thickness Swelling ◽  
Swelling Properties ◽  
Different Temperatures

The objective of this research was to evaluate the effects of thermal modifications, at different temperatures and exposure times, on the technological properties of mixed particleboard / OSB panels made out of Eucalyptus badjensis. Using the wood of Eucalyptus badjensis, Particleboard, OSB and mixed Particleboard/OSB panels (control and thermally modified) were manufactured. The mixed panels’ thermal modification was carried out under three temperatures (180ºC, 200ºC and 220ºC) and two exposure times (10 minutes and 12 minutes). For the panels’ manufacturing, 6% of phenol-formaldehyde adhesive and 1% of paraffin were employed, which was calculated based on the particles’ dry mass. The water absorption and thickness swelling properties were evaluated after 2 and 24 hours of immersion, in addition to the panels’ modulus of elasticity, modulus of rupture and internal bond. Based on the results, we were able to conclude that the thermal modification affected most of the physical properties positively. From the different exposure times studied, the most effective one was the period of 12 minutes, especially for water absorption after 2 hours, which caused a reduction of 11.27%. In turn, the most effective temperature was of 220ºC, highlighting the thickness swelling after 24 hours, which caused a swelling decrease of 23.76% in comparison with the control panels. Regarding the mechanical properties, the thermal modification, in terms of the studied exposure times and temperatures, did not affect the results of the mixed particleboard /OSB panels. 

scholarly journals Sifat Fisis dan Mekanis Papan Semen dari Serat Tandan Kosong Kelapa Sawit (The Physical and Mechanical Properties of Cement Board Made from Oil Palm Empty Fruit Bunches Fibers)

2016 ◽  
Vol 8 (2) ◽  
pp. 43-52 ◽  
Author(s):  
Djoko Purwanto
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Oil Palm ◽  
Modulus Of Elasticity ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Thickness Swelling ◽  
Empty Fruit Bunches ◽  
Screw Withdrawal ◽  
Cement Board

Oil palm empty fruit bunches (OPEFB) fiber were industrial waste that has not been widely used by the community, only stacked and cause odors that interfere with the surrounding environment. This research studied the utilization of OPEFB fiber for cement board products using cement as resin and CaCl2 as accelerator. Laboratory scale cement board made from OPEFB fiber were mixed with cement, and CaCl2. The composition of fiber and cement were 1:1, 1:1.5, 1:2, and CaCl2 variations were 0%, 1% and 3%. A mixture of fibers, cement and CaCl2 was compressed at the pressure of 4 ton for 24 hours. The cement boards were tested for physical and mechanical properties according to JIS A 5417-1992, and the results were compared to the requirements of the cement board JIS A 5417-1992. Cement board made from fiber and cement composition 1:1.5 and CaCl2 content 3% produced moisture content, thickness swelling, water absorption, density, modulus of rupture/MOR, modulus of elasticity/MOE and screw withdrawal strength that met the requirement of JIS A 5417-1992. The composition of fiber and cement and the variations of CaCl2 content produced significant effect on water content, water absorption, thickness swelling, modulus of rupture/MOR, modulus of elasticity/MOE and screw withdrawal strength on cement boards.Keywords : oil palm empty fruit bunches fiber, cement boards, physical and mechanical properties

scholarly journals The classical mechanics engineered of Bambusa vulgaris and Schizostachyum brachycladum

2021 ◽  
Vol 6 (2) ◽  
pp. 57-61
Author(s):  
Mohamad Saiful Sulaiman ◽  
Sitti Fatimah Mhd. Ramle ◽  
Rokiah Hashim ◽  
Othman Sulaiman ◽  
Mohd Hazim Mohamad Amini ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Moisture Content ◽  
Water Absorption ◽  
Classical Mechanics ◽  
Basic Density ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Flexural Test ◽  
Thickness Swelling ◽  
Bambusa Vulgaris

Physical and mechanical properties of Bambusa vulgaris and Schizostachyum brachycladum wereinvestigated. The sample were classified into two different ages which are young and mature foreach culm of bamboo. The aim of this study to investigate the physical properties such as density,basic density, moisture content, water absorption and thickness swelling. Other than that, themechanical properties also help to determine their flexural test for modulus of rupture (MOR) andmodulus of elasticity (MOE). The method used to analyse physical and mechanical properties werefollowing the ISO standard. From this study, young Bambusa vulgaris has indicated the highercontent of moisture content, water absorption and thickness swelling with 67.66%, 2.69% and34.03%, respectively while mature Schizostachyum brachycladum has shown the higher value inbasic density, density, and flexural test for MOR and MOE with 876.33 kg/m3, 1084.49 kg/m3, 317.01 N/mm2 and 122986.18 N/mm2, respectively.

Effect of Density on Physical and Mechanical Properties of Reconstituted Small-Sized Bamboo Fibrous Sheet Composite

2010 ◽  
Vol 150-151 ◽  
pp. 634-639 ◽  
Author(s):  
Rong Xian Zhu ◽  
Wen Ji Yu
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Thickness Swelling ◽  
Cold Pressing ◽  
Shearing Strength

The effect of density on physical and mechanical properties of phenolic-impregnated cold-pressing reconstituted small-sized bamboo fibrous sheet composite was evaluated. The results indicated that with the density increased from 0.85g/cm3 to 1.20 g/cm3: water absorption decreased, thickness swelling increased first and then decreased; the value of modulus of rupture(MOR) increased from 120MPa to 230MPa, R2 was 0.885; the value of modulus elasticity(MOE) increased from 1.8×104MPa to 2.8×104MPa, R2 was 0.978; the shearing strength (perpendicular loading) increased from 6.5MPa to 18MPa, R2 was 0.978;the shearing strength( parallel loading) increased from 6.3MPa to 26MPa, R2 was 0.973;the compression parallel to grain values increased from 80MPa to 120MPa.

scholarly journals KUALITAS PAPAN KOMPOSIT LIMBAH KULIT BATANG SAGU (Metroxylon sp) DAN PLASTIK POLIPROPILENA BERDASARKAN JUMLAH LAPISAN PENYUSUN

2018 ◽  
Vol 7 (1) ◽  
Author(s):  
Mayang Archila ◽  
Farah Diba ◽  
Dina Setyawati ◽  
. Nurhaida
Keyword(s):  
Mechanical Properties ◽  
Moisture Content ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Internal Bonding ◽  
Thickness Swelling ◽  
Composite Board ◽  
Average Value ◽  
Composite Layers ◽  
Sago Bark

The objective of this research is to evaluate the effect of the number of composite layers on the quality of the composite board from sago bark waste and plastic waste, and the number of composite layers that produce the best quality on composite board. The composite board is made with size 30 cm x 30 cm x 1 cm. The composition and division of the material was carried out manually with the polypropylene distribution divided into three parts: the front and rear respectively of 15%, and the center 70% of the plastic weight. Target density of composite boards was 0.7 g / cm3. The treatment used is based on the number of layers composing, which is 5 layers, 7 layers, 9 layers, 11 layers and 13 layers. After mixed the sago bark particle and waste of polypropylene, the materials then compressed with hot press at 180oC with pressure about ± 25 kg / cm2 for 10 minutes. The composite boards then tested the quality included physical and mechanical properties. Testing of physical and mechanical properties refers to JIS A 5908-2003 standard. Physical properties consist of density, moisture content, thickness swelling, and water absorption. Mechanical properties consist of modulus of rupture, modulus of elasticity, internal bonding, and modulus of screw holding strength. The study used a completely randomized design experiment consisting of 5 treatments and 3 replications. The results showed the average value of composite density was range between 0.6962 – 0.7896 g/cm3, the moisture content was range between 4.3388 % - 6.8066%, the thickness swelling was range between 8.2605% - 11.9615%, and water absorption was range between 17.2380% - 22.3867%. The average value of modulus of rupture was range between 60,0632 kg/cm2 – 64,4068 kg/cm2, the modulus of elasticity was range between 17935,1813g/cm2 – 32841,8278 kg/cm2, the internal bonding was range between 1,9268 kg/cm2  - 5,4119 kg/cm2, and the modulus of screw holding strength was range between 78,2530 kg/cm2 – 92,9677 kg/cm2. The composite board made from sago stem bark waste and polypropylene waste plastic with 13 layers treatment is the best composite board and fulfilled the JIS A 5908-2003 standard. Keywords: bark of sago, composite boards, layer of composite, polypropylenes plastic, waste

An attempt to use „Tetra Pak” waste material in particleboard technology

2021 ◽  
Vol 114 ◽  
pp. 70-75
Author(s):  
Radosław Auriga ◽  
Piotr Borysiuk ◽  
Alicja Auriga
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Core Layer ◽  
Waste Material ◽  
Thickness Swelling ◽  
The Core ◽  
Tetra Pak ◽  
The Impact

An attempt to use „Tetra Pak” waste material in particleboard technology. The study investigates the effect of addition Tetra Pak waste material in the core layer on physical and mechanical properties of chipboard. Three-layer chipboards with a thickness of 16 mm and a density of 650 kg / m3 were manufactured. The share of Tetra Pak waste material in the boards was varied: 0%, 5%, 10% and 25%. The density profile was measured to determine the impact of Tetra Pak share on the density distribution. In addition, the manufactured boards were tested for strength (MOR, MOE, IB), thickness swelling and water absorption after immersion in water for 2 and 24 hours. The tests revealed that Tetra Pak share does not affect significantly the value of static bending strength and modulus of elasticity of the chipboard, but it significantly decreases IB. Also, it has been found that Tetra Pak insignificantly decreases the value of swelling and water absorption of the chipboards.

Physical and Mechanical Properties of Glass Composite Material Made from Incinerated Scheduled Waste Slag and SLS Waste Glass

2012 ◽  
Vol 626 ◽  
pp. 280-288 ◽  
Author(s):  
Jariah Mohd Juoi ◽  
Dilip Arudra ◽  
Zulkifli Mohd Rosli ◽  
A.R. Toibah ◽  
Siti Rahmah Shamsuri ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Composite Material ◽  
Water Absorption ◽  
Physical And Mechanical Properties ◽  
Waste Glass ◽  
X Ray Diffraction ◽  
Glass Composite ◽  
X Ray ◽  
Land Site ◽  
Waste Loading

Incineration of scheduled waste and landfilling of the incineration residue (Bottom Slag) is extensively practised in Malaysia as a treatment method for scheduled waste. Land site disposal of Bottom Slag (BS) may lead to environmental health issues and reduces the availability of land to sustain the nations development. This research aims in producing Glass Composite Material (GCM) incorporating BS and Soda Lime Silicate (SLS) waste glass as an alternative method for land site disposal method and as an effort for recycling SLS waste glass .SLS waste glass originates from the urban waste and has been a waste stream in most of the nation whereby the necessity for recycling is in high priority.The effect of BS waste loading on the GCM is studied.Batches of powder mixture is formulated with 30 wt% to 70 wt % of BS powder and SLS waste glass powder for GCM sintering.The powder mixtures of BS and SLS waste glass is compacted by uniaxial pressing method and sintered at 800C with heating rate of 2C/min and 1 hour soaking time. Physical analysis of bulk density, apparent porosity, and water absorption is perfomed according to ASTM C-373 standard. Mechanical testing of microhardness vickers according to ASTM C1327 and Modulus of Rupture (MOR) according to ISO 10545-4 is conducted. Microstructural analysis is carried out using Scanning Electron Microscope and phase analysis by X-ray diffraction method.Phases identified are Anorthite sodian,Quartz,Hematite and Diopside from X-ray diffraction analysis. Higher BS waste loading shows weak physical and mechanical properties .GCM from batch formulation of 30 wt % BS and 70 wt% SLS waste glass has projected optimized physical and mechanical properties. It is observed this batch has projected lowest water absorption percentage of 1.17 % , lowest porosity percentage of 2.2 %, highest bulk density of 1.88 g/cm3and highest MOR of 70.57 Mpa and 5.6 GPa for Vickers Microhardness.

scholarly journals Effects of thermo-hydro-mechanical treatments on various physical and mechanical properties of poplar (Populus) wood

BioResources ◽  
2020 ◽  
Vol 15 (4) ◽  
pp. 9596-9610
Author(s):  
Yali Shao ◽  
Lili Li ◽  
Zhangjing Chen ◽  
Sunguo Wang ◽  
Ximing Wang
Keyword(s):  
Mechanical Properties ◽  
Thermal Treatment ◽  
Modulus Of Elasticity ◽  
Mechanical Treatment ◽  
Elasticity Modulus ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Compression Rate ◽  
Thickness Swelling ◽  
Maximum Thickness

Poplar (Populus) wood was subjected in this work to thermo-hydro-mechanical treatment. The influence of the treatment parameters on the physical and mechanical properties were investigated. The wood samples were densified under three compression ratios (0%, 30%, and 50%), and thermally treated at three temperatures (180 °C, 200 °C, and 220 °C), at three thermal treatment durations (3 h, 4 h, and 5 h). The density, modulus of elasticity, modulus of rupture, radial hardness, and thickness swelling were measured. The results showed that the densities of the samples increased by 36.6% to 49.7%. As the compression rate increased, the temperature, duration, modulus of elasticity, modulus of rupture, and hardness increased. However, the dimensions of the densified samples were less stable. Compared to the densified samples, the maximum thickness swelling could be reduced by 74% (from 29.7% to 7.8%) when subjected to a thermal treatment at 220 °C for 3 h.

scholarly journals Effects of Resin Content on the Characteristics of Bamboo Oriented Strand Board Prepared from Strands of Betung, Ampel, and Their Mixtures

2021 ◽  
Vol 9 (3) ◽  
pp. 454-465
Author(s):  
Tengku Muhammad Renzy Hariz ◽  
Indra Agus Santosa ◽  
Muhammad Iqbal Maulana ◽  
Marwanto ◽  
Denni Prasetia ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Dimensional Stability ◽  
Oriented Strand Board ◽  
Physical And Mechanical Properties ◽  
Resin Content ◽  
Thickness Swelling ◽  
Higher Dimensional ◽  
Bambusa Vulgaris ◽  
Dendrocalamus Asper

The objectives of this research were to evaluate bamboo-oriented strand board (BOSB) characteristics made from betung (Dendrocalamus asper), ampel (Bambusa vulgaris), and their mixtures at two different contents (3% and 5%) of methylene diphenyl di-isocyanate (MDI) adhesives. The strands were steam-treated at 126°C for 1 h under the pressure of 0.14 MPa. Three-layered BOSBs with a target density of 0.7 g/cm3 were made with the size of 30 cm x 30 cm x 0.9 cm and a shelling ratio of 1:2:1 (face:core:back layers). The physical and mechanical properties of BOSB were evaluated following JIS A 5908 (2003) standard, and the results were compared with the CSA 0437.0 Grade O-1 standard. The results show that BOSB from the mixtures of betung and ampel bamboo strands has higher dimensional stability as shown by the decrease in water absorption and thickness swelling and higher mechanical properties than single BOSB. All BOSBs with 5% resin content have higher dimensional stability, MOE, and MOR than BOSB with 3% resin content. The physical and mechanical properties of all BOSB manufactured met the CSA 0437.0 Grade O-1 standard. This study proved that BOSBs from the mixture of betung and ampel strands have the potential to be developed due to having better physical and mechanical qualities than a single BOSB. Keywords: ampel (Bambusa vulgaris), bamboo oriented strand board, betung (Dendrocalamus asper), resin content, strand mixtures

scholarly journals Preparation and performance of modified montmorillonite-reinforced wood-based foamed composites

BioResources ◽  
2020 ◽  
Vol 15 (2) ◽  
pp. 3566-3584
Author(s):  
Qingde Li ◽  
Yingyi Liang ◽  
Feng Chen ◽  
Tonghui Sang
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Flexural Modulus ◽  
Wood Fiber ◽  
Physical And Mechanical Properties ◽  
Thickness Swelling ◽  
Compression Process ◽  
Hygroscopic Properties ◽  
Bonding Effect ◽  
And Performance

Wood fiber was modified by impulse-cyclone drying treatment with poplar and montmorillonite as reinforcing materials; mMMT/polypropylene/wood fiber foaming composite was prepared by the hot compression process. The effects of modification, temperature, and content of montmorillonite on physical and mechanical properties of the composite were analyzed. Mechanical properties, porosity, shrinkage, water absorption, and thickness swelling tests showed that when mMMT reinforcement was 5 wt%, the best performance was achieved. The scanning electron microscopy observations showed that bubble holes were distributed widely and evenly, and mMMT appeared in the cell gap and was encapsulated by polypropylene, which maximized the bonding effect. Flexural strength was 27.5 MPa, flexural modulus was 2110 MPa, tensile strength was 20.0 MPa, and impact strength was 6.30 KJ/m2. When absolute volume of dense solid reached 70.8 cm3, porosity was 21.4% and shrinkage was 1.17%, which indicated that the water absorption increased most remarkably under that test condition. When equilibrium water absorption reached 9.28%, the thickness swelling decreased by 25%. The results showed that mMMT effectively optimized mechanical properties of wood-based foamed composites and improved hygroscopic properties.

Sign in / Sign up

Export Citation Format

Share Document