scholarly journals About the Possible Limitations in the Usage of the Non-Destructive Ultrasonic Pulse Velocity Method for Assessment of Cracks in Reinforced Concrete Structures, Subjected to Direct Environmental Exposure

Buildings ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 202 ◽  
Author(s):  
Ivan Ivanchev ◽  
Veselin Slavchev
Keyword(s):  
Reinforced Concrete ◽  
Experimental Studies ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Reinforced Concrete Beams ◽  
Safety And Reliability ◽  
External Conditions ◽  
Maximum Crack ◽  
Non Destructive

Failures occur in the structures of reinforced concrete buildings and facilities during their continuous exploitation, without being overloaded or exposed to extreme impacts, the most common being cracks. Their detection and change in time are related to the assessment of the state of the structures, their safety, and reliability during their construction and especially for their safety exploitation. This paper describes the results of the experimental studies conducted by authors aiming to verify the possibility of using the non-destructive ultrasonic pulse velocity method (NDUPVM) for detection and evaluation of cracks. Results of an experimental study of 12 reinforced concrete beams are presented. In previous experiments, some of them were subjected to bending until the maximum crack width of 0.3 mm was reached and others until yielding of the longitudinal reinforcement. The results obtained from the measurements of the depths of the normal cracks with different widths with NDUPVM were compared with the visually measured ones. In the present research cracks with the same width and with a similar depth were chosen. The influence of extreme external conditions to the accuracy of the measured crack depths by the NDUPVM was investigated. Non-destructive ultrasonic research was done by a portable device Proceq TICO.

scholarly journals Pengaruh Variasi Mutu Beton Bertulang Terhadap Cepat Rambat Gelombang Dengan Menggunakan Metode Non Destructive Test

2020 ◽  
Vol 14 (1) ◽  
pp. 60-69
Author(s):  
A.A. Lingga Ariya D. ◽  
◽  
Indradi Wijatmiko ◽  
Christin Remayanti Nainggolan ◽  
◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Indirect Method ◽  
Direct Method ◽  
Ultrasonic Pulse Velocity ◽  
Pulse Velocity ◽  
Reinforced Concrete Beams ◽  
Building Structures ◽  
Non Destructive ◽  
Test Objects

Preferably in testing, building structures need not be destroyed. Tests that can be used on the concrete can use non-destructive methods that do not damage the test objects. Examples of testing can use UPV tests that are aimed at knowing the quality of concrete from the pulse velocity. The test objects used in this study are reinforced concrete beams with dimensions 20 x 20 x 100 cm. Test objects are differentiated into 3 quality variations of reinforced concrete with quality of concrete12.5 MPa, 18.75 MPa, and 25 MPa. To conduct analysis of the concrete density used PUNDIT PL-200. Ultrasonic pulse velocity into parameters on this test. From the results of the tests, there are differences in the value of different coefficient of the R2 determination. Acquired coefficient value of determination R2 = 0.9076 in direct method. The coefficient value of determination R2 = 0.8718 in the semi-direct method. Coefficient value of determination R2 = 0.3042 at Indirect Method 2 point, and in indirect method 3 point the coefficient value of determination R2 = 0.7524. From this research also obtained comparisons between the three methods, namely between the direct method and the semi-direct method, direct method and indirect method, also semi-direct method and indirect method.

scholarly journals The Hydration, Mechanical, Autogenous Shrinkage, Durability, and Sustainability Properties of Cement–Limestone–Slag Ternary Composites

2021 ◽  
Vol 13 (4) ◽  
pp. 1881
Author(s):  
Mei-Yu Xuan ◽  
Yi Han ◽  
Xiao-Yong Wang
Keyword(s):  
Compressive Strength ◽  
Electrical Resistivity ◽  
Experimental Studies ◽  
Autogenous Shrinkage ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Hydration Heat ◽  
Granulated Blast Furnace Slag ◽  
Binder Ratio

This study examines the hydration–mechanical–autogenous shrinkage–durability–sustainability properties of ternary composites with limestone filler (LF) and ground-granulated blast furnace slag (BFS). Four mixtures were prepared with a water/binder ratio of 0.3 and different replacement ratios varying from 0 to 45%. Multiple experimental studies were performed at various ages. The experimental results are summarized as follows: (1) As the replacement levels increased, compressive strength and autogenous shrinkage (AS) decreased, and this relationship was linear. (2) As the replacement levels increased, cumulative hydration heat decreased. At the age of 3 and 7 days, there was a linear relationship between compressive strength and cumulative hydration heat. (3) Out of all mixtures, the ultrasonic pulse velocity (UPV) and electrical resistivity exhibited a rapid increase in the early stages and tended to slow down in the latter stages. There was a crossover of UPV among various specimens. In the later stages, the electrical resistivity of ternary composite specimens was higher than plain specimens. (4) X-ray diffraction (XRD) results showed that LF and BFS have a synergistic effect. (5) With increasing replacement ratios, the CO2 emissions per unit strength reduced, indicating the sustainability of ternary composites.

scholarly journals Evaluating the Durability of Green Cement Mortar Using Ultrasonic Pulse Velocity

2021 ◽  
Vol 877 (1) ◽  
pp. 012049
Author(s):  
Ali Abdulridha ◽  
Saif S. AlQuzweeni ◽  
Rasha S. AlKizwini ◽  
Zahra A. Saleh ◽  
K. S. Hashem
Keyword(s):  
Silica Fume ◽  
Cement Mortar ◽  
Experimental Studies ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Cement Kiln Dust ◽  
Cement Kiln ◽  
Negative Consequences ◽  
Kiln Dust

Abstract Various experimental studies have highlighted the negative consequences of Portland cement on health and the environment, such as toxic emissions and alkaline sewage. The development of environmentally acceptable substitutes for cement is thus one of the objectives of current investigations. The proposed environmental alternatives to cement, nevertheless, might have detrimental impacts on the concrete’s characteristics. This investigation intends to study the suitability as alternatives to cement in cement mortar, using industrial wastes like silica fume and cement kiln dust. As a replacement for cement, the cement mortars developed in this research continue from 0% to 60% silica fume and cement kiln dust. Ultrasonic pulse velocity tests at 1 to 4 weeks of age were conducted on hardened specimens. The findings showed that a low reduction in the pulse velocity resulted from high proportions of silica fume and cement kiln dust replacements, whereas an improvement in the characteristics of the mortars with low replacement ratios. Using low kiln dust and silica fume of 20 to 40%, the durability of mortars may increase.

scholarly journals Assessment of Concrete Compressive Strength by Ultrasonic Non-Destructive Test

2021 ◽  
Vol 318 ◽  
pp. 03004
Author(s):  
AbdulMuttalib I. Said ◽  
Baqer Abdul Hussein Ali
Keyword(s):  
Compressive Strength ◽  
Salt Content ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Experimental Program ◽  
Concrete Compressive Strength ◽  
Statistical Program ◽  
Non Destructive ◽  
Accurate Relation

This paper has carried out an experimental program to establish a relatively accurate relation between the ultrasonic pulse velocity (UPV) and the concrete compressive strength. The program involved testing concrete cubes of (100) mm and prisms of (100×100×300) cast with specified test variables. The samples are tested by using ultrasonic test equipment with two methods, direct ultrasonic pulse (DUPV) and surface (indirect) ultrasonic pulse (SUPV) for each sample. The obtained results were used as input data in the statistical program (SPSS) to predict the best equation representing the relation between the compressive strength and the ultrasonic pulse velocity. In this research 383 specimens were tested, and an exponential equation is proposed for this purpose. The statistical program has been used to prove which type of UPV is more suitable, the (SUPV) test or the (DUPV) test, to represent the relation between the ultrasonic pulse velocity and the concrete compressive strength. In this paper, the effect of salt content on the connection between the ultrasonic pulse velocity and the concrete compressive strength has also been studied.

Non-Destructive Testing for Concrete: Dynamic Modulus and Ultrasonic Velocity Measurements

2011 ◽  
Vol 243-249 ◽  
pp. 165-169 ◽  
Author(s):  
Iqbal Khan Mohammad
Keyword(s):  
Compressive Strength ◽  
Modulus Of Elasticity ◽  
Dynamic Modulus ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Non Destructive Testing ◽  
Destructive Testing ◽  
Dynamic Modulus Of Elasticity ◽  
Non Destructive

Nondestructive testing (NDT) is a technique to determine the integrity of a material, component or structure. The commonly NDT methods used for the concrete are dynamic modulus of elasticity and ultrasonic pulse velocity. The dynamic modulus of elasticity of concrete is related to the structural stiffness and deformation process of concrete structures, and is highly sensitive to the cracking. The velocity of ultrasonic pulses travelling in a solid material depends on the density and elastic properties of that material. Non-destructive testing namely, dynamic modulus of elasticity and ultrasonic pulse velocity was measured for high strength concrete incorporating cementitious composites. Results of dynamic modulus of elasticity and ultrasonic pulse velocity are reported and their relationships with compressive strength are presented. It has been found that NDT is reasonably good and reliable tool to measure the property of concrete which also gives the fair indication of the compressive strength development.

Non-Destructive Tests as Durability Indicators in Cement Mortars with Pozzolanic Substitutions

2017 ◽  
Vol 902 ◽  
pp. 9-13
Author(s):  
Rosalía Ruiz Ruiz ◽  
Elia Mercedes Alonso Guzmán ◽  
Wilfrido Martínez Molina ◽  
Hugo Luis Chávez García ◽  
Judith Alejandra Velázquez Perez
Keyword(s):  
Mechanical Characteristics ◽  
Ultrasonic Pulse Velocity ◽  
Good Alternative ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Cement Industry ◽  
Capillary Absorption ◽  
Pozzolanic Material ◽  
Cement Mortars ◽  
Non Destructive

Cement industry is responsible of 5-7% of CO2 emissions to the atmosphere. This is preoccupant because this is one of the greenhouse effect gases which cause global warming. Pozzolanic material incorporation in cement mortars elaboration represents a good alternative to partially substitute cement, since its chemical composition could contribute to improvement of its durability and mechanical characteristics. In this research, mortars with pozzolanic substitutions are evaluated through non-destructive tests as: capillary absorption, electrical resistivity, and ultrasonic pulse velocity to the age of 1000 days. The results suggested that the incorporation of pozzolanic material as partial substitutes of Portland cement increases the mortars properties mainly in substitutions of CBC 20%, PN 10, and 30%.

scholarly journals Using Support Vector Machine to Improve Ultrasonic Pulse Velocity Test for Concrete

2018 ◽  
Vol 207 ◽  
pp. 01001
Author(s):  
Tu Quynh Loan Ngo ◽  
Yu-Ren Wang
Keyword(s):  
Compressive Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Support Vector ◽  
Non Destructive Testing ◽  
Testing Methods ◽  
Destructive Testing ◽  
Compressive Strength Of Concrete ◽  
Non Destructive

In the construction industry, to evaluate the compressive strength of concrete, destructive and non-destructive testing methods are used. Non-destructive testing methods are preferable due to the fact that those methods do not destroy concrete samples. However, they usually give larger percentage of error than using destructive tests. Among the non-destructive testing methods, the ultrasonic pulse velocity test is the popular one because it is economic and very simple in operation. Using the ultrasonic pulse velocity test gives 20% MAPE more than using destructive tests. This paper aims to improve the ultrasonic pulse velocity test results in estimating the compressive strength of concrete using the help of artificial intelligent. To establish a better prediction model for the ultrasonic pulse velocity test, data collected from 312 cylinder of concrete samples are used to develop and validate the model. The research results provide valuable information when using the ultrasonic pulse velocity tests to the inputs data in addition with support vector machine by learning algorithms, and the actual compressive strengths are set as the target output data to train the model. The results show that both MAPEs for the linear and nonlinear regression models are 11.17% and 17.66% respectively. The MAPE for the support vector machine models is 11.02%. These research results can provide valuable information when using the ultrasonic pulse velocity test to estimate the compressive strength of concrete.

Sign in / Sign up

Export Citation Format

Share Document