scholarly journals Overview of Spark Plasma Texturing of Functional Ceramics

Ceramics ◽  
2021 ◽  
Vol 4 (1) ◽  
pp. 97-107
Author(s):  
Jacques G. NOUDEM ◽  
Yiteng XING
Keyword(s):  
Electrical Resistivity ◽  
Structural Transition ◽  
Bulk Material ◽  
Superconducting Properties ◽  
Plasma Sintering ◽  
New Process ◽  
Spark Plasma ◽  
P Type ◽  
Remarkable Reduction ◽  
Functional Ceramics

This work reports the progress in the preparation of superconducting and thermoelectric lamellar compounds processed by the unconventional Spark Plasma Sintering (SPS). The SPS equipment was modified with the aim of obtaining the textured and dense superconductor Bi2Sr2Ca2Cu3O10,p-type oxide thermoelectric bulk as Ca3Co4O9 and Ca3-xAgxCo4O9/Ag composites respectively. The new process is referred to as Spark Plasma Texturing (SPT). During SPT, the bulk material can freely deform. As a result, inter-grain preferential crystallographic orientation is created. The series of sintered and textured samples using the same Ag content were processed respectively. From the results, we can evidence: (i) the magnetic and/or structural transition around 350 °C, for both series of samples. (ii) The electrical resistivity (ρ) decreases with increasing Ag-substituted or Ag-added. (iii) The Seebeck coefficient (S) of the textured series is higher than that of the sintered series. In the case of the Ag-substituted, S, decreases with Ag content. The optimized composite is found to be Ca2.6Ag0.4Co4O9/8wt% Ag. We can note the remarkable reduction of ρ, and the improvement of power factor values up to 360 μW.m−1.K−2.The superconducting properties of single phased Bi2Sr2Ca2Cu3O10 (Bi2223) consolidated using SPS and SPT will also be discussed.

scholarly journals Thermal and Electronic Transport Properties of the Half-Heusler Phase ScNiSb

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1723 ◽  
Author(s):  
Karol Synoradzki ◽  
Kamil Ciesielski ◽  
Igor Veremchuk ◽  
Horst Borrmann ◽  
Przemysław Skokowski ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Electrical Resistivity ◽  
Small Magnitude ◽  
Single Phase Sample ◽  
Heusler Phase ◽  
Temperature Range ◽  
Arc Melting ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
P Type

Thermoelectric properties of the half-Heusler phase ScNiSb (space group F 4 ¯ 3m) were studied on a polycrystalline single-phase sample obtained by arc-melting and spark-plasma-sintering techniques. Measurements of the thermopower, electrical resistivity, and thermal conductivity were performed in the wide temperature range 2–950 K. The material appeared as a p-type conductor, with a fairly large, positive Seebeck coefficient of about 240 μV K−1 near 450 K. Nevertheless, the measured electrical resistivity values were relatively high (83 μΩm at 350 K), resulting in a rather small magnitude of the power factor (less than 1 × 10−3 W m−1 K−2) in the temperature range examined. Furthermore, the thermal conductivity was high, with a local minimum of about 6 W m−1 K−1 occurring near 600 K. As a result, the dimensionless thermoelectric figure of merit showed a maximum of 0.1 at 810 K. This work suggests that ScNiSb could be a promising base compound for obtaining thermoelectric materials for energy conversion at high temperatures.

Orientation Distribution in Bi2Te3-Based Compound Prepared by Spark Plasma Sintering

2005 ◽  
Vol 486-487 ◽  
pp. 646-649 ◽  
Author(s):  
Ki Tae Kim ◽  
Cheol Ho Lim ◽  
Yong Hwan Kim ◽  
Dong Choul Cho ◽  
Young Sup Lee ◽  
...  
Keyword(s):  
Electrical Resistivity ◽  
Spark Plasma Sintering ◽  
Figure Of Merit ◽  
Orientation Distribution ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
P Type

P-type Bi0.5Sb1.5Te3 compounds doped with 3wt.% Te were fabricated by spark plasma sintering after mixing large powders(PL) and small powders(PS). We could obtained the highest figure of merit(Zc) of 2.89×10-3/K in sintered compound mixed to PL:PS=80:20. This resulted from the increase of orientation by large powders(PS) and the reduce of pores by small powders. The figure of merit(Zc) of the sintered compound using only small powders(PS) showed lower value of 2.67×10-3/K compared with that of sintered compound mixed to PL:PS=80:20 due to the increase of electrical resistivity.

Microstructure and Thermoelectric Properties of P-Type Bi0.5Sb1.5Te3 Compounds Prepared by Spark Plasma Sintering

2006 ◽  
Vol 510-511 ◽  
pp. 1122-1125
Author(s):  
Won Seung Cho ◽  
Dong Choul Cho ◽  
Cheol Ho Lim ◽  
C.H. Lee ◽  
Woon Suk Hwang ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Electrical Resistivity ◽  
Seebeck Coefficient ◽  
Spark Plasma Sintering ◽  
Hydrogen Reduction ◽  
Sintering Temperature ◽  
Reduction Process ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
P Type

The microstructure and thermoelectrical properties of the 4wt% Te doped p-type Bi0.5Sb1.5Te3 compounds, fabricated by using spark plasma sintering in the temperature ranging from 250°C to 350°C, were characterized. The density of the sintered compounds was increased to 99.2% of theoretical density by carrying out the consolidation at 350oC for 2 min. The Seebeck coefficient, thermal conductivity and electrical resistivity were dependent on hydrogen reduction process and sintering temperature. The Seebeck coefficient increased with reduction process while the electrical resisitivity significantly decreased. Also, the electrical resistivity decreased and thermal conductivity increased with sintering temperature. The results suggest that the carrier density and mobility vary with reduction process and sintering temperature. The highest figure of merit of 3.5×10-3/K was obtained for the compounds spark plasma sintered at 350°C for 2 min by using the hydrogen-reduced powders.

Ultra-Fine Grained Ti-15Mo Alloy Prepared by Powder Metallurgy

2018 ◽  
Vol 941 ◽  
pp. 1276-1281
Author(s):  
Anna Terynková ◽  
Jiří Kozlík ◽  
Kristína Bartha ◽  
Tomáš Chráska ◽  
Josef Stráský
Keyword(s):  
Powder Metallurgy ◽  
Bulk Material ◽  
Alpha Phase ◽  
Full Density ◽  
Fine Grained ◽  
Cryogenic Milling ◽  
Aircraft Manufacturing ◽  
Plasma Sintering ◽  
Beta Matrix ◽  
Spark Plasma

Ti-15Mo alloy belongs to metastable β-Ti alloys that are currently used in aircraft manufacturing and Ti15Mo alloy is a perspective candidate for the use in medicine thanks to its biotolerant composition. In this study, Ti15Mo alloy was prepared by advanced techniques of powder metallurgy. The powder of gas atomized Ti-15Mo alloy was subjected to cryogenic milling to achieve ultra-fine grained microstructure within the powder particles. Powder was subsequently compacted using spark plasma sintering (SPS). The effect of cryogenic milling on the microstructure and phase composition of final bulk material after SPS was studied by scanning electron microscopy. Sintering at 750°C was not sufficient for achieving full density in gas atomized powder, while milled material could be successfully sintered at this temperature. Alpha phase particles precipitated during sintering and their size, as well as the size of beta matrix grains, was strongly affected by the sintering temperature.

scholarly journals Shape Memory NiTi and NiTiCu Alloys Obtained by Spark Plasma Sintering Process

2015 ◽  
Vol 13 ◽  
pp. 83-90 ◽  
Author(s):  
Cristiana Diana Cristea ◽  
Magdalena Lungu ◽  
Alexander M. Balagurov ◽  
Virgil Marinescu ◽  
Otilia Culicov ◽  
...  
Keyword(s):  
Shape Memory ◽  
Intermetallic Compounds ◽  
Spark Plasma Sintering ◽  
Sintering Process ◽  
Transformation Behavior ◽  
Plasma Sintering ◽  
New Process ◽  
Shape Memory Properties ◽  
Spark Plasma ◽  
Niti Shape Memory Alloys

The addition of Cu to near equiatomic NiTi shape memory alloys (SMAs) can provide some modifications of their shape memory properties by affecting their transformation behavior. The same effect was obtained in the case of Ni3Ti2 and Ni4Ti3 precipitates presence in the microstructure of NiTi. Also the substitution of Cu to NiTi alloys increases the hardness of the materials. This paper presents the microstructural and mechanical investigations of NiTi and NiTiCu alloys obtained by spark plasma sintering (SPS) process that represents a great potential for researchers as a new process for the fabrication of intermetallic compounds.

Fabrication of Bi-Te Based Thermoelectric Semiconductors by Using Hybrid Powders

2005 ◽  
Vol 297-300 ◽  
pp. 875-880
Author(s):  
Cheol Ho Lim ◽  
Ki Tae Kim ◽  
Yong Hwan Kim ◽  
Dong Choul Cho ◽  
Young Sup Lee ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Single Crystals ◽  
Thermoelectric Properties ◽  
Thermoelectric Materials ◽  
Figure Of Merit ◽  
Bending Strength ◽  
Mixing Ratio ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
P Type

P-type Bi0.5Sb1.5Te3 compounds doped with 3wt% Te were fabricated by spark plasma sintering and their mechanical and thermoelectric properties were investigated. The sintered compounds with the bending strength of more than 50MPa and the figure-of-merit 2.9×10-3/K were obtained by controlling the mixing ratio of large powders (PL) and small powders (PS). Compared with the conventionally prepared single crystal thermoelectric materials, the bending strength was increased up to more than three times and the figure-of-merit Z was similar those of single crystals. It is expected that the mechanical properties could be improved by using hybrid powders without degradation of thermoelectric properties.

Thermoelectric properties of undoped p-type CoSb3 prepared by vertical Bridgman crystal growth and spark plasma sintering

2006 ◽  
Vol 415 (1-2) ◽  
pp. 251-256 ◽  
Author(s):  
Satoru Furuyama ◽  
Tsutomu Iida ◽  
Shinsuke Matsui ◽  
Masayasu Akasaka ◽  
Keishi Nishio ◽  
...  
Keyword(s):  
Crystal Growth ◽  
Spark Plasma Sintering ◽  
Thermoelectric Properties ◽  
Plasma Sintering ◽  
Vertical Bridgman ◽  
Spark Plasma ◽  
Bridgman Crystal Growth ◽  
P Type

The Influence of RuO2 Addition on the Thermoelectric Properties of BiSbTe Alloys

2012 ◽  
Vol 512-515 ◽  
pp. 1651-1654 ◽  
Author(s):  
Yu Kun Xiao ◽  
Zhi Xiang Li ◽  
Jun Jiang ◽  
Sheng Hui Yang ◽  
Ting Zhang ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Thermoelectric Properties ◽  
Lattice Thermal Conductivity ◽  
Combined Process ◽  
Plasma Sintering ◽  
The Matrix ◽  
Spark Plasma ◽  
Xrd Patterns ◽  
Factor Α ◽  
P Type

P-type BiSbTe/RuO2 composite was fabricated using a combined process of melting and spark plasma sintering. The XRD patterns showed that RuO2 reacted with the matrix for the RuO2 content of 1.0 wt% and 4.0 wt% samples. The measured thermoelectric properties showed that the highest electrical conductivity was obtained for the sample with 2.0 wt% RuO2. The power factor (α2σ/κ) decreased with the increase of RuO2 below 450 K. The lattice thermal conductivity was lower than that of BiSbTe over the whole temperature range for BiSbTe/2.0 wt% RuO2.

Sign in / Sign up

Export Citation Format

Share Document