scholarly journals Optimization of Friction Stir Process Parameters for Enhancement in Surface Properties of Al 7075-SiC/Gr Hybrid Surface Composites

Coatings ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 830 ◽  
Author(s):  
Namdev Ashok Patil ◽  
Srinivasa Rao Pedapati ◽  
Othman Bin Mamat ◽  
Abdul Munir Hidayat Syah Lubis
Keyword(s):  
Wear Rate ◽  
Surface Properties ◽  
Base Alloy ◽  
Nano Particles ◽  
Micro Hardness ◽  
Wear Properties ◽  
Friction Stir ◽  
Surface Composites ◽  
Al 7075 ◽  
Independent Parameters

Friction stir processing (FSP) has evolved as an important technique in fabrication of metal matrix composites. The surface properties enhancement is obtainable by insertion of desired discontinuous particular reinforcements into base alloy using FSP. Despite having high specific strength, more applications of Al alloys are restricted due to their poor surface properties under various loading conditions. In this study, the main focus is on enhancing the microhardness and wear properties of Al 7075 base alloy by means of uniform dispersion of silicon carbide and graphite (SiC/Gr) nano particles into the base alloy using the FSP technique. The tool rotational speed (w: 500, 1000, 1500 rpm), tool traverse speed (v: 20, 30, 40 mm/min), reinforcement particles hybrid ratio (HR: 60:40, 75:25, 90:10) and volume percentage (vol%: 4%, 8%, 12%) are used as independent parameters. The effect of these parameters on microstructure, micro hardness and wear properties of surface composites are studied in detail. For desired wear rate and microhardness as responses, the aforementioned independent parameters are optimized using response surface methodology (RSM). The significance of factors and their interactions for maximizing hardness and minimizing wear rate and coefficient of friction (COF) were determined. Analysis of variance (ANOVA) for responses has been carried out, and the models were found to be significant in all three responses. The minimum wear rate of 0.01194 mg/m was obtained for parameters w 1500 rpm, v 40 mm/min, HR 60:40, vol% 4 (Run 10). The maximum micro hardness of 300 HV obtained for parameters w 1000 rpm, v 30 mm/min, HR 75:25, vol% 12 (Run 14). The presence and uniform distribution of SiC and Gr into the base alloy was confirmed through field-emission scanning electron microscopy (FESEM) imaging, energy-dispersive X-ray spectroscopy (EDX) and mapping tests. The wear rate and COF decreased significantly due to graphitized mechanically mixed layer developed at the sliding contacts. The microhardness of resultant composites observed to be dependent on effect of the independent parameters on extent of inherent precipitates dissolution and grain size strengthening in the resultant materials.

scholarly journals Improving the Wear Properties of Aluminum 6082 Alloy by Surface Compositing with Zro2 Ceramic Particles Via Friction Stir Processing

2018 ◽  
Vol 15 (1) ◽  
pp. 68-74
Author(s):  
N. Yuvaraj
Keyword(s):  
Friction Stir Processing ◽  
Volume Content ◽  
Surface Engineering ◽  
Base Alloy ◽  
Base Material ◽  
Matrix Composites ◽  
Wear Properties ◽  
Friction Stir ◽  
Surface Composites ◽  
Lower Volume

Aluminum based metal matrix composites are given more attention in fabrication of surface engineering applications due to their excellent mechanical and wear properties. In this study, Friction stir processing (FSP) method was used to fabricate the surface composite with inserting different volume % of ZrO2 reinforcement particles in the Aluminum 6082 alloy. The hardness and triblogical characteristics of fabricated surface composites and base alloy were investigated. The higher volume content of reinforcement surface revealed higher hardness and higher wear resistance compared to the lower volume content reinforcement surface and base material. The wear worn-out of composite surfaces and base alloy were examined through SEM for understanding the wear mechanisms.

Effect of High Temperature on Wear Behavior of Stir Cast Aluminium/Boron Carbide Composites

2020 ◽  
Vol 22 (4) ◽  
pp. 1031-1046
Author(s):  
X. Canute ◽  
M. C. Majumder
Keyword(s):  
High Temperature ◽  
Wear Rate ◽  
Boron Carbide ◽  
Wear Behavior ◽  
Base Alloy ◽  
Weight Fraction ◽  
Sliding Velocity ◽  
Wear Properties ◽  
High Temperature Wear ◽  
The Matrix

AbstractThe need for development of high temperature wear resistant composite materials with superior mechanical properties and tribological properties is increasing significantly. The high temperature wear properties of aluminium boron carbide composites was evaluated in this investigation. The effect of load, sliding velocity, temperature and reinforcement percentage on wear rate was determined by the pin heating method using pin heating arrangement. The size and structure of base alloy particles change considerably with an increase of boron carbide particles. The wettability and interface bonding between the matrix and reinforcement enhanced by the addition of potassium flurotitanate. ANOVA technique was used to study the effect of input parameters on wear rate. The investigation reveals that the load had higher significance than sliding velocity, temperature and weight fraction. The pin surface was studied with a high-resolution scanning electron microscope. Regression analysis revealed an extensive association between control parameters and response. The developed composites can be used in the production of automobile parts requiring high wear, frictional and thermal resistance.

scholarly journals Mechanical and Microstructural Characterization of Friction Stir Welded SiC and B4C Reinforced Aluminium Alloy AA6061 Metal Matrix Composites

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3110
Author(s):  
Kaveripakkam Suban Ashraff Ali ◽  
Vinayagam Mohanavel ◽  
Subbiah Arungalai Vendan ◽  
Manickam Ravichandran ◽  
Anshul Yadav ◽  
...  
Keyword(s):  
Wear Rate ◽  
Aluminium Alloy ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Weld Zone ◽  
Base Material ◽  
Matrix Composites ◽  
Wear Properties ◽  
Friction Stir ◽  
Behavioural Aspects

This study focuses on the properties and process parameters dictating behavioural aspects of friction stir welded Aluminium Alloy AA6061 metal matrix composites reinforced with varying percentages of SiC and B4C. The joint properties in terms of mechanical strength, microstructural integrity and quality were examined. The weld reveals grain refinement and uniform distribution of reinforced particles in the joint region leading to improved strength compared to other joints of varying base material compositions. The tensile properties of the friction stir welded Al-MMCs improved after reinforcement with SiC and B4C. The maximum ultimate tensile stress was around 172.8 ± 1.9 MPa for composite with 10% SiC and 3% B4C reinforcement. The percentage elongation decreased as the percentage of SiC decreases and B4C increases. The hardness of the Al-MMCs improved considerably by adding reinforcement and subsequent thermal action during the FSW process, indicating an optimal increase as it eliminates brittleness. It was seen that higher SiC content contributes to higher strength, improved wear properties and hardness. The wear rate was as high as 12 ± 0.9 g/s for 10% SiC reinforcement and 30 N load. The wear rate reduced for lower values of load and increased with B4C reinforcement. The microstructural examination at the joints reveals the flow of plasticized metal from advancing to the retreating side. The formation of onion rings in the weld zone was due to the cylindrical FSW rotating tool material impression during the stirring action. Alterations in chemical properties are negligible, thereby retaining the original characteristics of the materials post welding. No major cracks or pores were observed during the non-destructive testing process that established good quality of the weld. The results are indicated improvement in mechanical and microstructural properties of the weld.

scholarly journals Development of High Performance (Mechanical and Wear Properties) of AA 6061-Hybrid Nano Composites Via Liquid Metallurgy Route

2019 ◽  
Vol 22 (2) ◽  
pp. 143-150
Author(s):  
Hussain J. M. Al-Alkawi ◽  
Abduljabbar Owaid Hanfesh ◽  
Saja Mohammed Noori Mohammed Rauof
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Wear Rate ◽  
Yield Strength ◽  
Base Metal ◽  
Young Modulus ◽  
Nano Particles ◽  
Wear Properties ◽  
Constant Weight ◽  
Weight Percentage

This research is devoted to study the influence of different weight percent concerning to the additions of Ti and Cu on mechanical and tribological properties of AA6061. The composite materials consist of different weight percentage of Ti (0.2, 0.4, and 0.6) wt% and constant weight percentage of Cu (0.2) wt% which were fabricated by liquid metallurgy route technique. Microstructural characterization and phases have been examined by using SEM (scanning electron microscopic).SEM examination showed uniform distribution of nano Ti and Cu in AA6061. The consequences of mechanical tests demonstrated clear enhancement in mechanical properties, such as ultimate tensile strength, yield strength, young modulus, ductility% and hardness at additive percentage of 0.4% Ti+0.2%Cu nano particles incorporated into molten AA6061. Percentage of enhancement ultimate tensile strength is about 73.3%, yield strength about 82.7%, young modulus is about 21.2%, the  Vickers hardness about 42.6% and the decreasing in ductility was about 25.2% compared with the metal matrix (AA6061). The wear rate test was performed by using pin on disc rig for both hybrid nano composite and base metal (AA6061) under various loads (10,15and 20) N with sliding speed (1.282) m/sec at a (10) min’s time. The results showed a decrease in wear rate at 0.4%Ti+0.2%Cu compared with the base metal (AA6061). Improvement percentage of wear rate is about 105% at 20 N load.

Wear Assessment of Ti/SiC Surface Nano-Composite Layer and its Associated CP-Ti Substrate

2012 ◽  
Vol 445 ◽  
pp. 595-600 ◽  
Author(s):  
Ali Shamsipur ◽  
Seyed Farshid Kashani-Bozorg ◽  
Abbas Zarei Hanzaki
Keyword(s):  
Surface Layer ◽  
Wear Behavior ◽  
Composite Layer ◽  
Pure Titanium ◽  
Commercially Pure Titanium ◽  
Micro Hardness ◽  
Wear Properties ◽  
Friction Stir ◽  
Pin On Disc ◽  
Cp Ti

In the present investigation, the surface of a commercially pure titanium (CP-Ti) substrate was modified to Ti/SiC nanocomposite layer employing friction stir processing technique; nanosized SiC powder was introduced into the stir zone provided by a rotating and advancing tool. The fabricated nanocomposite surface layer exhibited a micro hardness value of ~535HV which is much greater than 160HV of the substrate material using Vickers micro hardness testing. In addition, the un-treated CP-Ti substrate showed sever wear regime in the pin-on-disc test against the hardened AISI 52100 steel. It suffers extensive typical adhesive wear dominated by plastic deformation as evidenced by scanning electron microscopy. Also, deep grooves were formed, i.e. evidence of abrasive wear. Contrary to this, enhanced wear properties were detected for the Ti/SiC nanocomposite surface layer, i.e. lower coefficient of friction and weight loss. The nanocomposite surface layer was found to be adherent to the underlying substrate during the pin-on-disc test. The superior wear behavior of the nanocomposite surface layer is attributed to its improved micro hardness value due to the presence of hard nanosize SiC particles in a refined titanium matrix.

scholarly journals The Effect of Incorporating Ceramic Particles with Different Morphologies on the Microstructure, Mechanical and Tribological Behavior of Hybrid TaC_ BN/AA2024 Nanocomposites

Coatings ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1560
Author(s):  
Emad Ismat Ghandourah ◽  
Essam B. Moustafa ◽  
Hossameldin Hussein ◽  
Ahmed O. Mosleh
Keyword(s):  
Mechanical Properties ◽  
Wear Resistance ◽  
Base Alloy ◽  
Tantalum Carbide ◽  
Heavy Particles ◽  
Friction Stir ◽  
Surface Composites ◽  
Mechanical Durability ◽  
Research Challenge ◽  
Aluminum Alloy Surface

Improving the mechanical durability and wear resistance of aluminum alloys is a research challenge that can be solved by their reinforcement with ceramics. This article is concerned with the improvement of the mechanical properties and wear resistance of the AA2024 aluminum alloy surface. Surface composites were prepared by incorporating a hybrid of heavy particles (tantalum carbide (TaC), light nanoparticles, and boron nitride (BN)) into the AA2024 alloy using the friction stir process (FSP) approach. Three pattern holes were milled in the base metal to produce the composites with different volume fractions of the reinforcements. The effects of the FSP and the reinforcements on the microstructure, mechanical properties, and wear resistance are investigated. In addition to the FSP, the reinforced particles contributed to greater grain refinement. The rolled elongated grains became equiaxed ultrafine grains reaching 6 ± 1 µm. The refinement and acceptable distribution in the reinforcements significantly improved the hardness and wear resistance of the produced composites. Overall, the hardness was increased by 60% and the wear resistance increased by 40 times compared to the base alloy.

Sign in / Sign up

Export Citation Format

Share Document