scholarly journals The Effect of Specimen Size and Test Procedure on the Creep Behavior of ME21 Magnesium Alloy

Crystals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 918
Author(s):  
Bettina Camin ◽  
Maximilian Gille
Keyword(s):  
Magnesium Alloy ◽  
Creep Behavior ◽  
Test Procedure ◽  
Primary Creep ◽  
Creep Process ◽  
Transport Sector ◽  
Creep Tests ◽  
Miniature Specimen ◽  
Heat Treated ◽  
A Minor

Lightweight constructions and materials offer the opportunity to reduce CO2 emissions in the transport sector. As components in vehicles are often exposed to higher temperatures above 40% of the melting temperature, there is a risk of creep. The creep behavior usually is investigated based on standard procedures. However, lightweight constructions frequently have dimensions not adequately represented by standardized specimen geometries. Therefore, comparative creep experiments on non-standardized miniature and standardized specimens are performed. Due to a modified test procedure specified by a miniature creep device, only the very first primary creep stage shows a minor influence, but subsequently, no effect on the creep process is detected. The creep behavior of hot extruded and heat treated ME21 magnesium alloy is investigated. It is observed that the creep parameters determined by the miniature and standard creep tests are different. As the deviations are systematic, qualitatively, evidence of the creep behavior is achieved. The creep parameters obtained, and particularly the creep strain and the strain rate, show a higher creep resistance of the miniature specimen. An initial higher number of twinned grains and possible multiaxiality in the gauge volume of the miniature specimen can be responsible.

An Experimental Study on the Effect of Prior Plastic Straining on Creep Behavior of 304 Stainless Steel

1993 ◽  
Vol 115 (2) ◽  
pp. 200-203 ◽  
Author(s):  
Z. Xia ◽  
F. Ellyin
Keyword(s):  
Stainless Steel ◽  
Plastic Strain ◽  
Strain Rate ◽  
Creep Behavior ◽  
Test Procedure ◽  
Constant Strain Rate ◽  
304 Stainless Steel ◽  
Creep Model ◽  
Plastic Strain Rate ◽  
Creep Tests

Constant strain-rate plastic straining followed by creep tests were conducted to investigate the effect of prior plastic straining on the subsequent creep behavior of 304 stainless steel at room temperature. The effects of plastic strain and plastic strain-rate were delineated by a specially designed test procedure, and it is found that both factors have a strong influence on the subsequent creep deformation. A creep model combining the two factors is then developed. The predictions of the model are in good agreement with the test results.

Creep Behavior and Microstructural Stability of Lamellar γ-T1AI (Cr, Mo, Si, B) with Extremely Fine Lamellar Spacing

2000 ◽  
Vol 646 ◽  
Author(s):  
Wolfram Schillinger ◽  
Dezhi Zhang ◽  
Gerhard Dehm ◽  
Arno Bartels ◽  
Helmut Clemens
Keyword(s):  
Creep Rate ◽  
Creep Behavior ◽  
Lamellar Microstructure ◽  
Lamellar Spacing ◽  
Primary Creep ◽  
Vacuum Arc ◽  
Internal Stresses ◽  
Microstructural Stability ◽  
Thermodynamical Equilibrium ◽  
Creep Tests

ABSTRACTγ-T1AI (Cr, Mo, Si, B) specimens with two different fine lamellar microstructures were produced by vacuum arc melting followed by a two-stage heat treatment. The average lamellar spacing was determined to be 200 nm and 25–50 nm, respectively. Creep tests at 700°C showed a very strong primary creep for both samples. After annealing for 24 hours at 1000 °C the primary creep for both materials is significantly decreased. The steady-state creep for the specimens with the wider lamellar spacing appears to be similar to the creep behavior prior to annealing while the creep rate of the material with the previously smaller lamellar spacing is significantly higher. Optical microscopy and TEM-studies show that the microstructure of the specimens with the wider lamellar specing is nearly unchanged, whereas the previously finer material was completely recrystallized to a globular microstructure with a low creep resistance. The dissolution of the fine lamellar microstructure was also observed during creep tests at 800 °C as manifested in an acceleration of the creep rate. It is concluded that extremely fine lamellar microstructures come along with a very high dislocation density and internal stresses which causes the observed high primary creep. The microstructure has a composition far away from the thermodynamical equilibrium which leads to a dissolution of the structure even at relatively low temperatures close to the intended operating temperature of γ-T1AI structural parts. As a consequence this limits the benefit of fine lamellar microstructures on the creep behavior.

scholarly journals Nonlinear Viscoelastic–Plastic Creep Model Based on Coal Multistage Creep Tests and Experimental Validation

Energies ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 3468 ◽  
Author(s):  
Junxiang Zhang ◽  
Bo Li ◽  
Conghui Zhang ◽  
Peng Li
Keyword(s):  
Creep Behavior ◽  
Physical Property ◽  
Creep Model ◽  
Creep Process ◽  
Creep Tests ◽  
Model Based ◽  
Nonlinear Viscoelastic ◽  
Improved Model ◽  
And Control ◽  
Plastic Creep

The development of fractures, which determine the complexity of coal creep characteristics, is the main physical property of coal relative to other rocks. This study conducted a series of multistage creep tests to investigate the creep behavior of coal under different stress levels. A negative elastic modulus and a non-Newtonian component were introduced into the classical Nishihara model based on the theoretical analysis of the experimental results to propose a nonlinear viscoelastic–plastic creep model for describing the non-decay creep behavior of coal. The validity of the model was verified by experimental data. The results show that this improved model can preferably exhibit decelerating, steady state, and accelerating creep behavior during the non-decay creep process. The fitting accuracy of the improved model was significantly higher than that of the classical Nishihara model. Given that acceleration creep is a critical stage in predicting the instability and failure of coal, its successful description using this improved model is crucial for the prevention and control of coal dynamic disasters.

Tensile and Compressive Creep Behavior of IN718 Alloy Manufactured by Selective Laser Melting

2020 ◽  
Vol 986 ◽  
pp. 102-108 ◽  
Author(s):  
Zhen Xu ◽  
Chuan Guo ◽  
Zhen Rong Yu ◽  
Xin Li ◽  
Xiao Gang Hu ◽  
...  
Keyword(s):  
Creep Behavior ◽  
Chemical Potential ◽  
Creep Process ◽  
Tension Stress ◽  
Creep Tests ◽  
Compressive Creep ◽  
Large Size ◽  
Stress Orientation ◽  
Evolution Of Microstructure ◽  
Tension Compression Asymmetry

Tensile and compressive creep behavior of SLMed IN718 alloy under 973K (700°C) were investigated. Crept samples were analyzed by SEM and TEM to expose evolution of microstructure, precipitates and dislocation structure during the creep process. Results show that initial creep rate under compression is higher than under tension for the same creep conditions. Minimum creep rates are approximately the same both in tensile and compressive creep tests. The different creep behaviors may be related to the fact that tension stress promotes precipitations of fine needle-like γ′′ phases, while compression stress promotes precipitations of large size δ phases. The tension-compression asymmetry owns to the increment of chemical potential varying with the stress orientation.

scholarly journals An Improved Nishihara Model for Frozen Loess considering the Influence of Temperature

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Xin Li ◽  
Enlong Liu ◽  
Bingtang Song ◽  
Xingyan Liu
Keyword(s):  
Creep Behavior ◽  
Microscopic Analysis ◽  
Confining Pressure ◽  
Deviatoric Stress ◽  
Frozen Soil ◽  
Experimental Results ◽  
Creep Process ◽  
Model Parameters ◽  
Creep Tests ◽  
Deviator Stress

A series of triaxial creep tests under the constant confining pressure are performed on frozen loess specimens, and the creep behavior of the frozen loess with respect to variations in both temperature and deviator stress is examined. Experimental results illustrate that the frozen loess specimens present the attenuation creep at the lower deviatoric stress, whereas the nonattenuation creep under the higher deviatoric stress level, and with a drop in the temperature, the deviator stress value which the exhibition of nonattenuation creep needs will increase under the constant confining pressure condition. According to the microscopic analysis on deformation characteristics in the creep process of frozen soil, both temperature and external stress will cause the hardening and weakening effects, affecting the creep properties of frozen loess. By introducing the hardening variable and damage variable to consider the hardening and weakening effects of the frozen loess, an improved Nishihara model is proposed. The correlations between model parameters and the temperature as well as deviator stress are determined. The comparisons between model predictions and experimental results show that the improved creep constitutive model proposed here can not only describe the whole creep process well, but also reveal the influences of the temperature and deviator stress on the creep behavior of frozen loess, which demonstrate its accuracy and usefulness.

Creep Behavior for Alloy 617 in Air at 950°C

2010 ◽  
Vol 654-656 ◽  
pp. 508-511 ◽  
Author(s):  
Woo Gon Kim ◽  
Song Nan Yin ◽  
Gyeong Geon Lee ◽  
Yong Wan Kim
Keyword(s):  
Creep Behavior ◽  
Primary Creep ◽  
Secondary Creep ◽  
Creep Tests ◽  
Alloy 617 ◽  
Very High Temperature Reactor ◽  
Creep Curves ◽  
High Temperature Reactor ◽  
Very High ◽  
Cr2o3 Layer

Creep behavior for Alloy 617, which is considered as one of the major structural materials of a very high temperature reactor, was investigated in air at 950oC. Creep experimental data was obtained by a series of creep tests with different stress levels at 950oC. Alloy 617 revealed little primary creep strains and unclear secondary creep stages. A tertiary creep stage was initiated from a low strain level and was dominant in full creep curves. The creep constants of A, n, m, and C in Norton’s power law and Monkman-Grant relationships were determined. In microstructure observations of crept specimens, it was found that a Cr2O3 oxidation layer was formed on the surface, and just beneath the Cr2O3 layer, an internal Al-oxide sub layer was formed with rod shapes. Also, below the internal sub layer, a thick carbide-depleted zone was developed due to reaction of the chromia and carbide precipitates. The thickness of the outer Cr-oxide layer increased with increasing creep rupture times. The increasing tendency showed a smooth slope like a parabolic curve.

Combined constitutive model for creep and steady flow rate of frozen soil in an unconfined condition

2017 ◽  
Vol 54 (7) ◽  
pp. 907-914 ◽  
Author(s):  
Guofang Xu ◽  
Chong Peng ◽  
Wei Wu ◽  
Jilin Qi
Keyword(s):  
Constitutive Model ◽  
Strain Rate ◽  
Steady Flow ◽  
Flow Rate ◽  
Creep Behavior ◽  
Frozen Soil ◽  
Creep Process ◽  
Model Parameters ◽  
Creep Failure ◽  
Creep Tests

A combined constitutive model is developed for the creep behavior of frozen soil in an unconfined condition. The model is obtained by coupling two stress- and time-dependent models, which are responsible for the primary and tertiary creep stages. The model parameters are dependent on temperature and can be readily determined from the strain rate–time curves at two creep stresses. The model performance is demonstrated by simulating the complete strain–time and strain rate–time curves (including primary, secondary, and tertiary stages) of frozen sand and frozen clay in uniaxial creep tests under different creep stresses. Moreover, two equations are obtained from the combined model. One shows a good capability in describing the relationship between creep strength and the time to creep failure. The other makes an excellent prediction of the steady flow rate in a typical creep process. Both equations can reflect the effects of stress and temperature on the creep behavior of frozen soil.

Statistical analysis of creep behavior in thermoset and thermoplastic composites reinforced with carbon and glass fibers

2020 ◽  
pp. 030932472097663
Author(s):  
Francisco Maciel Monticeli ◽  
Ana Karoline dos Reis ◽  
Roberta Motta Neves ◽  
Luis Felipe de Paula Santos ◽  
Edson Cocchieri Botelho ◽  
...  
Keyword(s):  
Creep Behavior ◽  
Glass Fibers ◽  
Laminated Composite ◽  
Analytical Models ◽  
Thermoplastic Composites ◽  
Temperature Dependent ◽  
Creep Tests ◽  
Thermoset Composites ◽  
Strain Behavior ◽  
Sensitivity Range

The thermoplastic and thermoset laminates reinforced with different fibers generate variations in the laminated composite mechanical behavior. This work aims to analyze thermoplastic and thermoset composites creep behavior with a reduced number of experiments, applying curve-fitting analytical models (Weibull and Findley) and statistical approach (ANOVA, F-test, and SRM) in order to describe creep behavior. Creep tests were carried out using a design of experiments to define parameter levels, aiming to reduce the number of the experiments, keeping reliability relevance. The temperature shows a stronger influence of creep deformation compared with the use of distinct materials. Thermoplastic matrices seem to be more sensitive to deformation, decreasing the reinforcement contribution. On the other hand, the creep resistance of the thermoset matrix conducts a significant contribution of strain behavior for the reinforcement used. The Findley model showed a temperature-dependent response. While, the Weibull-based model exhibits temperature and material-dependence, ensuring a greater sensitivity range of the parameters applied, an essential factor for a more realistic method description.

scholarly journals Temperature-Dependent Creep Behavior and Quasi-Static Mechanical Properties of Heat-Treated Wood

Forests ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 968
Author(s):  
Dong Xing ◽  
Xinzhou Wang ◽  
Siqun Wang
Keyword(s):  
Mechanical Properties ◽  
Creep Behavior ◽  
Cell Walls ◽  
Treated Wood ◽  
Crosslinking Reaction ◽  
Depth Sensing ◽  
Temperature Dependent ◽  
Heat Treated ◽  
Static Mechanical ◽  
Static Mechanical Properties

In this paper, Berkovich depth-sensing indentation has been used to study the effects of the temperature-dependent quasi-static mechanical properties and creep deformation of heat-treated wood at temperatures from 20 °C to 180 °C. The characteristics of the load–depth curve, creep strain rate, creep compliance, and creep stress exponent of heat-treated wood are evaluated. The results showed that high temperature heat treatment improved the hardness of wood cell walls and reduced the creep rate of wood cell walls. This is mainly due to the improvement of the crystallinity of the cellulose, and the recondensation and crosslinking reaction of the lignocellulose structure. The Burgers model is well fitted to study the creep behavior of heat-treated wood cell walls under different temperatures.

Sign in / Sign up

Export Citation Format

Share Document